Resources

In a university electrical engineering laboratory, a student performs a four-terminal sensing (Kelvin bridge) characterization of a precision alloy resistor to eliminate lead-wire contact resistance. A regulated current source injects a precisely calibrated current of I=2.500 AI = 2.500\text{ A} through the current leads of the device under test. A digital multimeter configured as a high-impedance voltmeter measures a potential drop of ΔV=18.75 mV\Delta V = 18.75\text{ mV} across the dedicated inner voltage sensing leads. (a) Calculate the precise resistance RR of the test specimen in milliohms (mΩ\text{m}\Omega). (b) If each outer current lead possesses a parasitic contact resistance of Rlead=0.120 ΩR_{\text{lead}} = 0.120\ \Omega, calculate the total voltage drop VsourceV_{\text{source}} output by the current source. (c) Explain why connecting the voltmeter across the inner potential terminals measures only the specimen's resistance, clearly contrasting the current circulating through the loop with the voltage measured across the specific branch.

Answer and steps

Final answer

(a) R=7.500 mΩ=7.500×10−3 ΩR = 7.500\text{ m}\Omega = 7.500 \times 10^{-3}\ \Omega; (b) Vsource=I(2Rlead+R)=2.500 A×(0.240 Ω+0.00750 Ω)=0.6188 V≈0.619 VV_{\text{source}} = I(2 R_{\text{lead}} + R) = 2.500\text{ A} \times (0.240\ \Omega + 0.00750\ \Omega) = 0.6188\text{ V} \approx 0.619\text{ V}; (c) The inner voltmeter has an extremely high input impedance (>10 GΩ> 10\text{ G}\Omega), drawing virtually zero current through the sensing leads (Isense≈0I_{\text{sense}} \approx 0), which ensures zero voltage drop across the voltage lead wires; thus, the voltmeter isolates and measures solely the electrostatic potential difference across the sample itself, while the full 2.500 A2.500\text{ A} current continues to flow through the separate power loop containing the lead resistance.

Steps

Part (a): Determining the Resistance of the Specimen

By Ohm's law, the resistance RR of a component is defined by the ratio of the potential difference ΔV\Delta V across its terminals to the electric current II passing through it:

R=ΔVIR = \frac{\Delta V}{I}

Given:

  • Measured voltage drop: ΔV=18.75 mV=18.75×10−3 V\Delta V = 18.75\text{ mV} = 18.75 \times 10^{-3}\text{ V}
  • Regulated current: I=2.500 AI = 2.500\text{ A}

Substitute these values into Ohm's law:

R=18.75×10−3 V2.500 A=7.500×10−3 Ω=7.500 mΩR = \frac{18.75 \times 10^{-3}\text{ V}}{2.500\text{ A}} = 7.500 \times 10^{-3}\ \Omega = 7.500\text{ m}\Omega


Part (b): Calculating the Total Source Voltage

The current source must drive the full current II through the entire closed current loop. This loop consists of:

  1. The lead resistance of the outgoing wire, RleadR_{\text{lead}}
  2. The specimen resistance, RR
  3. The lead resistance of the return wire, RleadR_{\text{lead}}

Because these three resistive elements are in series, the total equivalent resistance of the loop is:

Rtotal=2Rlead+RR_{\text{total}} = 2 R_{\text{lead}} + R

Substitute the known values:

Rtotal=2(0.120 Ω)+0.00750 Ω=0.240 Ω+0.00750 Ω=0.2475 ΩR_{\text{total}} = 2(0.120\ \Omega) + 0.00750\ \Omega = 0.240\ \Omega + 0.00750\ \Omega = 0.2475\ \Omega

The total voltage delivered by the constant current source is:

Vsource=I⋅Rtotal=2.500 A×0.2475 Ω=0.61875 V≈0.619 VV_{\text{source}} = I \cdot R_{\text{total}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.61875\text{ V} \approx 0.619\text{ V}

(or 0.6188 V0.6188\text{ V} to four significant figures).


Part (c): Why Four-Terminal Sensing Eliminates Lead Resistance

To understand how four-terminal (Kelvin) sensing avoids error, compare the two separate circuits:

  1. Current Path (Excitation Loop): The power source forces the calibrated current I=2.500 AI = 2.500\text{ A} through the outer wires. Because these wires carry substantial current, a noticeable voltage drop occurs across each lead (Vlead=I⋅Rlead=2.500 A×0.120 Ω=0.300 VV_{\text{lead}} = I \cdot R_{\text{lead}} = 2.500\text{ A} \times 0.120\ \Omega = 0.300\text{ V}). In a standard two-wire measurement, these voltage drops would add directly to the measured signal, leading to an enormous measurement error.
  2. Voltage Sensing Path (Measurement Branch): The voltmeter connects directly across the sample via its own dedicated inner leads. A modern digital voltmeter possesses an extremely high input impedance (typically >10 GΩ> 10\text{ G}\Omega). As a result, the current diverted into the voltage-sensing leads is practically zero (Isense≈0I_{\text{sense}} \approx 0).

Because Isense≈0I_{\text{sense}} \approx 0, the voltage drop across the parasitic resistance of the sensing leads is negligible:

Vsense-lead=Isense⋅Rsense-lead≈0 VV_{\text{sense-lead}} = I_{\text{sense}} \cdot R_{\text{sense-lead}} \approx 0\text{ V}

Consequently, the voltmeter measures the electrostatic potential difference across the sample alone, completely bypassing the voltage drops across the outer current-carrying leads.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that a closed circuit loop has two outer current leads and includes only a single lead resistance in the total source voltage calculation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=ΔVI⟹R=18.75 mV2.500 A=7.50 mΩR = \frac{\Delta V}{I} \Longrightarrow R = \frac{18.75\text{ mV}}{2.500\text{ A}} = 7.50\text{ m}\Omega

  2. Step 2

    Rtotal=R+Rlead=0.0075 Ω+0.120 Ω=0.1275 ΩR_{\text{total}} = R + R_{\text{lead}} = 0.0075\ \Omega + 0.120\ \Omega = 0.1275\ \Omega

    Correct

    Rtotal=2Rlead+R=2(0.120 Ω)+0.00750 Ω=0.2475 ΩR_{\text{total}} = 2 R_{\text{lead}} + R = 2(0.120\ \Omega) + 0.00750\ \Omega = 0.2475\ \Omega

    A complete circuit loop requires two outer leads (the outgoing feed wire and the return wire). Both leads carry the excitation current, so you must add 2Rlead2 R_{\text{lead}} to the specimen resistance.

  3. Step 3

    Vsource=I×Rtotal=2.500 A×0.1275 Ω=0.31875 VV_{\text{source}} = I \times R_{\text{total}} = 2.500\text{ A} \times 0.1275\ \Omega = 0.31875\text{ V}

    Correct

    Vsource=I⋅Rtotal=2.500 A×0.2475 Ω=0.61875 V≈0.619 VV_{\text{source}} = I \cdot R_{\text{total}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.61875\text{ V} \approx 0.619\text{ V}

    Your calculation correctly multiplied your total resistance by the current, but the numerical answer was affected by omitting the second lead resistance in the previous step.

  4. Step 4

    The voltmeter has extremely high internal resistance, so negligible current flows through the inner potential leads. With zero current in the sensing branch, there is no IR drop across the sense leads, measuring only the potential difference across the specimen while current circulates through the outer loop.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law to calculate the specimen resistance in part (a).

You clearly explained how high voltmeter impedance prevents current flow and eliminate lead-resistance voltage drops in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Single-lead loop omission

You forgot that a physical current loop requires both a supply wire and a return wire, including only one lead resistance instead of two.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking that current excitation leads in a four-wire measurement form a closed circuit requiring two separate conductor paths (each having its own contact and lead resistance) connected to the specimen.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for Both Current Path Conductors
  • Every closed current loop has a forward path and a return path; the total outer wire resistance is Rwires=2RleadR_{\text{wires}} = 2 R_{\text{lead}}.

  • Always trace the full closed path from the source terminal out to the load and back to the source terminal.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include both the outgoing and return current leads: Rtotal=R+2Rlead=0.00750 Ω+2(0.120 Ω)=0.2475 ΩR_{\text{total}} = R + 2 R_{\text{lead}} = 0.00750\ \Omega + 2(0.120\ \Omega) = 0.2475\ \Omega.

  2. Recalculate the source voltage: Vsource=I⋅Rtotal=2.500 A×0.2475 Ω=0.6188 VV_{\text{source}} = I \cdot R_{\text{total}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.6188\text{ V}.

Final answer

Vsource=0.6188 VV_{\text{source}} = 0.6188\text{ V} (or 0.619 V0.619\text{ V})

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the complete circuit loop when working with lead resistance to visually verify that both the feed and return wires are included.

  • Double-check that the number of series lead resistances matches the number of connection wires in the excitation circuit.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the prefix milli- as 10⁻⁶ instead of 10⁻³, leading to an incorrect resistance calculation by three orders of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔV=18.75×10−6 V  ⟹  R=ΔVI=18.75×10−6 V2.500 A=7.50×10−6 Ω  ⟹  R=0.0075 mΩ\Delta V = 18.75 \times 10^{-6}\text{ V} \implies R = \frac{\Delta V}{I} = \frac{18.75 \times 10^{-6}\text{ V}}{2.500\text{ A}} = 7.50 \times 10^{-6}\ \Omega \implies R = 0.0075\text{ m}\Omega

    Correct

    ΔV=18.75 mV=18.75×10−3 V  ⟹  R=18.75×10−3 V2.500 A=7.500×10−3 Ω=7.500 mΩ\Delta V = 18.75\text{ mV} = 18.75 \times 10^{-3}\text{ V} \implies R = \frac{18.75 \times 10^{-3}\text{ V}}{2.500\text{ A}} = 7.500 \times 10^{-3}\ \Omega = 7.500\text{ m}\Omega

    You confused the metric prefix milli- (m−=10−3\text{m}- = 10^{-3}) with micro- (μ−=10−6\mu- = 10^{-6}). As a result, your voltage conversion was too small by a factor of 10310^3, giving R=0.0075 mΩR = 0.0075\text{ m}\Omega instead of 7.500 mΩ7.500\text{ m}\Omega.

  2. Step 2

    Rtotal=R+2×Rlead=0.0000075 Ω+0.240 Ω=0.2400075 Ω  ⟹  Vsource=2.500 A×0.2400075 Ω=0.60001875 VR_{\text{total}} = R + 2 \times R_{\text{lead}} = 0.0000075\ \Omega + 0.240\ \Omega = 0.2400075\ \Omega \implies V_{\text{source}} = 2.500\text{ A} \times 0.2400075\ \Omega = 0.60001875\text{ V}

    Correct

    Rtotal=2Rlead+R=0.240 Ω+0.00750 Ω=0.2475 Ω  ⟹  Vsource=2.500 A×0.2475 Ω=0.61875 V≈0.619 VR_{\text{total}} = 2 R_{\text{lead}} + R = 0.240\ \Omega + 0.00750\ \Omega = 0.2475\ \Omega \implies V_{\text{source}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.61875\text{ V} \approx 0.619\text{ V}

    Your series resistance formula and application of Ohm's law were completely correct, but the numerical result was affected by substituting the incorrect resistance value from part (a).

  3. Step 3

    The voltmeter draws near-zero current because of its high input impedance, preventing any voltage drop across the inner contacts. Thus, ΔV\Delta V reflects only the potential across the specimen, even though the full 2.500 A2.500\text{ A} flows through the outer loop.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and set up Ohm's law (R=ΔVIR = \frac{\Delta V}{I}).

You correctly modeled the total circuit resistance by including both outer lead resistances in series with the specimen.

You accurately explained the physical reason why four-terminal sensing eliminates lead-wire contact resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Prefix Confusion

You substituted 10−610^{-6} for the prefix milli- (extm ext{m}) instead of 10−310^{-3}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the metric prefix milli- (10−310^{-3}) with micro- (10−610^{-6}) during unit conversion.

REASONING PATH
Your ACEpath teacher’s suggested approach
Metric Prefixes for Small Quantities
  • milli- (m\text{m}) represents 10−310^{-3}, whereas micro- (μ\mu) represents 10−610^{-6}.

  • Always double-check the prefix letter before converting: lowercase m\text{m} is milli- (10−310^{-3}), while Greek μ\mu is micro- (10−610^{-6}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the measured voltage using milli- (10−310^{-3}): ΔV=18.75 mV=18.75×10−3 V\Delta V = 18.75\text{ mV} = 18.75 \times 10^{-3}\text{ V}.

  2. Recalculate specimen resistance: R=18.75×10−3 V2.500 A=7.500×10−3 Ω=7.500 mΩR = \frac{18.75 \times 10^{-3}\text{ V}}{2.500\text{ A}} = 7.500 \times 10^{-3}\ \Omega = 7.500\text{ m}\Omega.

  3. Recompute total loop resistance: Rtotal=2(0.120 Ω)+0.00750 Ω=0.2475 ΩR_{\text{total}} = 2(0.120\ \Omega) + 0.00750\ \Omega = 0.2475\ \Omega.

  4. Calculate source voltage: Vsource=2.500 A×0.2475 Ω=0.61875 V≈0.619 VV_{\text{source}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.61875\text{ V} \approx 0.619\text{ V}.

Final answer

(a) R=7.500 mΩR = 7.500\text{ m}\Omega; (b) Vsource≈0.619 VV_{\text{source}} \approx 0.619\text{ V}; (c) Valid conceptual explanation as written.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review standard SI prefixes from tera- (101210^{12}) down to pico- (10−1210^{-12}) to build instant recall.

  • Practice converting mixed-prefix Ohm's law problems (e.g., millivolts to microamps) to reinforce prefix fluency.

OverviewACEpath Teacher's Diagnosis

03 The student believes that current divides equally between the voltmeter branch and the specimen rather than recognizing that the high-impedance voltmeter draws virtually zero current.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=ΔVI  ⟹  R=0.01875 V2.500 A=7.50 mΩR = \frac{\Delta V}{I} \implies R = \frac{0.01875\text{ V}}{2.500\text{ A}} = 7.50\text{ m}\Omega

  2. Step 2

    Rtotal=0.0075 Ω+2×0.120 Ω=0.2475 Ω  ⟹  Vsource=2.500 A×0.2475 Ω=0.61875 VR_{\text{total}} = 0.0075\ \Omega + 2 \times 0.120\ \Omega = 0.2475\ \Omega \implies V_{\text{source}} = 2.500\text{ A} \times 0.2475\ \Omega = 0.61875\text{ V}

  3. Step 3

    The current divides equally between the specimen and the voltmeter branch, so each receives half the current. Since the current splits, the voltmeter measures only the specimen because the outer lead voltage drops are bypassed by the split current.

    Correct

    A digital voltmeter has an extremely high internal resistance (RV≫RR_V \gg R), so it draws virtually zero current (Isense≈0I_{\text{sense}} \approx 0). Therefore, almost the entire 2.500 A2.500\text{ A} current flows through the specimen, producing negligible IRIR drop along the inner sensing leads and isolating the true potential difference across the specimen.

    Current does not divide equally. Parallel current division depends inversely on branch resistances (I1/I2=R2/R1I_1 / I_2 = R_2 / R_1). Because a voltmeter has an enormous input impedance (typically >10 GΩ> 10\text{ G}\Omega) compared to the milliohm specimen, virtually all 2.500 A2.500\text{ A} continues through the specimen, leaving Imeter≈0I_{\text{meter}} \approx 0.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Ohm's law to determine the specimen resistance in part (a).

You correctly accounted for both outer lead contact resistances in the series current loop in part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Voltmeter Current Division Misconception

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the parallel junction as splitting current equally between the voltmeter and the specimen, overlooking that current divides inversely proportional to branch resistance and that an ideal or high-impedance voltmeter has near-infinite resistance, drawing almost zero current.

REASONING PATH
Your ACEpath teacher’s suggested approach
Voltmeter Input Impedance
  • A voltmeter is designed with extremely high internal resistance (RV→∞R_V \to \infty) so that connecting it in parallel does not disturb the circuit.

  • Assume the sensing branch draws Isense≈0I_{\text{sense}} \approx 0, meaning the main current loop remains unaltered.

Parallel Current Division
  • For two parallel branches, current divides inversely with resistance: Ibranch=ItotalRotherR1+R2I_{\text{branch}} = I_{\text{total}} \frac{R_{\text{other}}}{R_1 + R_2}.

  • Check the branch resistances before assuming how current splits; equal split only occurs when branch resistances are identical.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the input impedance of the measurement instrument: a digital voltmeter has RV>10 GΩR_V > 10\text{ G}\Omega, whereas the specimen has R=7.5 mΩR = 7.5\text{ m}\Omega.

  2. Apply current division: because RV≫RR_V \gg R, the current entering the voltmeter sensing leads is Isense=IRR+RV≈0 AI_{\text{sense}} = I \frac{R}{R + R_V} \approx 0\text{ A}.

  3. Evaluate lead drops: the parasitic resistance of the inner voltage leads causes zero voltage drop (Vdrop=IsenseRsense-lead≈0 VV_{\text{drop}} = I_{\text{sense}} R_{\text{sense-lead}} \approx 0\text{ V}).

  4. Conclude: the voltmeter senses solely the electrostatic potential drop ΔV\Delta V across the specimen without including the I⋅RleadI \cdot R_{\text{lead}} drops of the outer excitation wires.

Final answer

The voltmeter possesses an extremely high input impedance, drawing virtually zero current (Isense≈0I_{\text{sense}} \approx 0). Consequently, all 2.500 A2.500\text{ A} flows through the specimen, no voltage drop occurs across the potential sensing leads, and the meter measures only the true potential difference across the specimen.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how ideal and real meters behave in circuit analysis (ammeters have R≈0R \approx 0, voltmeters have R≈∞R \approx \infty).

  • Practice drawing the two distinct loops in Kelvin sensing: the high-current excitation loop and the zero-current voltage sensing loop.

Lock it in

Similar question

01

A current source delivers 3.00 A3.00\text{ A} through two leads (each having a resistance of 0.050 Ω0.050\ \Omega) to a low-resistance shunt resistor of 15.0 mΩ15.0\text{ m}\Omega. Calculate the total voltage output by the current source.

Answer

0.345 V0.345\text{ V}. Total resistance is Rtotal=2Rlead+Rshunt=2(0.050 Ω)+0.0150 Ω=0.115 ΩR_{\text{total}} = 2 R_{\text{lead}} + R_{\text{shunt}} = 2(0.050\ \Omega) + 0.0150\ \Omega = 0.115\ \Omega. Therefore, Vsource=I⋅Rtotal=3.00 A×0.115 Ω=0.345 VV_{\text{source}} = I \cdot R_{\text{total}} = 3.00\text{ A} \times 0.115\ \Omega = 0.345\text{ V}.

02

In a 4-point probe sheet resistance test, a current of I=10.0 mAI = 10.0\text{ mA} is passed between two outer probes. The contact resistance at each outer probe is 15.0 Ω15.0\ \Omega, and the sample's bulk resistance between the probes is 120.0 Ω120.0\ \Omega. What total potential difference must the current source supply across its output terminals?

Answer

1.50 V1.50\text{ V}. The loop includes two outer contact resistances and the sample: Rtotal=2(15.0 Ω)+120.0 Ω=150.0 ΩR_{\text{total}} = 2(15.0\ \Omega) + 120.0\ \Omega = 150.0\ \Omega. Thus, Vsource=I⋅Rtotal=10.0×10−3 A×150.0 Ω=1.50 VV_{\text{source}} = I \cdot R_{\text{total}} = 10.0 \times 10^{-3}\text{ A} \times 150.0\ \Omega = 1.50\text{ V}.

03

A precision power supply maintains a constant current I=5.00 AI = 5.00\text{ A} through a sensor of resistance Rsensor=0.020 ΩR_{\text{sensor}} = 0.020\ \Omega. If the supply output voltage is measured to be 0.850 V0.850\text{ V}, determine the resistance of each individual outer lead wire assuming identical identical supply and return leads.

Answer

0.075 Ω0.075\ \Omega. The total loop resistance is Rtotal=VI=0.850 V5.00 A=0.170 ΩR_{\text{total}} = \frac{V}{I} = \frac{0.850\text{ V}}{5.00\text{ A}} = 0.170\ \Omega. Since Rtotal=2Rlead+RsensorR_{\text{total}} = 2 R_{\text{lead}} + R_{\text{sensor}}, we have 2Rlead=0.170 Ω−0.020 Ω=0.150 Ω2 R_{\text{lead}} = 0.170\ \Omega - 0.020\ \Omega = 0.150\ \Omega, so Rlead=0.075 ΩR_{\text{lead}} = 0.075\ \Omega per wire.

Loading workspace…