Resources

A low-power microelectronics test circuit is powered by a miniature DC cell providing 3.30 V3.30\text{ V}. The circuit consists of a series resistor R1=4.70 kΩR_1 = 4.70\text{ k}\Omega connected to a parallel pair consisting of R2=10.0 kΩR_2 = 10.0\text{ k}\Omega and R3=15.0 kΩR_3 = 15.0\text{ k}\Omega. Convert all resistances to fundamental SI units (Ω\Omega), and determine the current entering the parallel sub-network expressed in microamperes (μA\mu\text{A}) and the electrical energy consumed by the entire network in a time span of 2.50 ms2.50\text{ ms}, expressed in microjoules (μJ\mu\text{J}).

Answer and steps

Final answer

Itotal=308 μAI_{\text{total}} = 308\,\mu\text{A}; U=2.54 μJU = 2.54\,\mu\text{J}

Steps

01

Unit Conversion to SI Base Units

The prefix kilo (k\text{k}) corresponds to 10310^3. Converting each given value into standard SI units:

  • R1=4.70 kΩ=4.70×103 Ω=4700 ΩR_1 = 4.70\text{ k}\Omega = 4.70 \times 10^3\ \Omega = 4700\ \Omega
  • R2=10.0 kΩ=10.0×103 Ω=10000 ΩR_2 = 10.0\text{ k}\Omega = 10.0 \times 10^3\ \Omega = 10000\ \Omega
  • R3=15.0 kΩ=15.0×103 Ω=15000 ΩR_3 = 15.0\text{ k}\Omega = 15.0 \times 10^3\ \Omega = 15000\ \Omega
  • V=3.30 VV = 3.30\text{ V}
  • Δt=2.50 ms=2.50×10−3 s\Delta t = 2.50\text{ ms} = 2.50 \times 10^{-3}\text{ s}

02

Equivalent Resistance of the Circuit

The circuit consists of resistor R1R_1 connected in series with the parallel pair formed by R2R_2 and R3R_3.

First, calculate the equivalent resistance of the parallel combination, RpR_p:

Rp=R2⋅R3R2+R3=10000 Ω⋅15000 Ω10000 Ω+15000 Ω=1.50×10825000 Ω=6000 ΩR_p = \frac{R_2 \cdot R_3}{R_2 + R_3} = \frac{10000\ \Omega \cdot 15000\ \Omega}{10000\ \Omega + 15000\ \Omega} = \frac{1.50 \times 10^8}{25000}\ \Omega = 6000\ \Omega

Next, add the series resistor R1R_1 to find the total equivalent resistance, ReqR_{\text{eq}}:

Req=R1+Rp=4700 Ω+6000 Ω=10700 ΩR_{\text{eq}} = R_1 + R_p = 4700\ \Omega + 6000\ \Omega = 10700\ \Omega


03

Current Entering the Parallel Sub-Network

Because R1R_1 is in series with the entire parallel pair, the total current supplied by the cell passes through R1R_1 and enters the junction of the parallel sub-network. Using Ohm's law:

Itotal=VReq=3.30 V10700 Ω≈3.0841×10−4 AI_{\text{total}} = \frac{V}{R_{\text{eq}}} = \frac{3.30\text{ V}}{10700\ \Omega} \approx 3.0841 \times 10^{-4}\text{ A}

Converting this value to microamperes (1 μA=10−6 A1\ \mu\text{A} = 10^{-6}\text{ A}):

Itotal=3.0841×10−4 A×106 μA1 A≈308 μAI_{\text{total}} = 3.0841 \times 10^{-4}\text{ A} \times \frac{10^6\ \mu\text{A}}{1\text{ A}} \approx 308\ \mu\text{A}


04

Electrical Energy Consumed

The total electrical power dissipated by the circuit network is given by:

P=V⋅Itotal=3.30 V⋅(3.0841×10−4 A)≈1.0178×10−3 WP = V \cdot I_{\text{total}} = 3.30\text{ V} \cdot (3.0841 \times 10^{-4}\text{ A}) \approx 1.0178 \times 10^{-3}\text{ W}

The electrical energy UU consumed in time Δt=2.50×10−3 s\Delta t = 2.50 \times 10^{-3}\text{ s} is:

U=P⋅Δt=(1.0178×10−3 W)⋅(2.50×10−3 s)≈2.544×10−6 JU = P \cdot \Delta t = (1.0178 \times 10^{-3}\text{ W}) \cdot (2.50 \times 10^{-3}\text{ s}) \approx 2.544 \times 10^{-6}\text{ J}

Converting to microjoules (1 μJ=10−6 J1\ \mu\text{J} = 10^{-6}\text{ J}):

U≈2.54 μJU \approx 2.54\ \mu\text{J}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student sums all three resistances in series instead of combining R₂ and R₃ in parallel, leading to an overestimation of total resistance and an incorrect current and energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    R1=4700 ΩR_1 = 4700\ \Omega, R2=10000 ΩR_2 = 10000\ \Omega, R3=15000 ΩR_3 = 15000\ \Omega

  2. Step 2

    Rtotal=R1+R2+R3=4700+10000+15000=29700 ΩR_{\text{total}} = R_1 + R_2 + R_3 = 4700 + 10000 + 15000 = 29700\ \Omega

    Correct

    Rp=R2R3R2+R3=6000 Ω  ⟹  Req=R1+Rp=4700 Ω+6000 Ω=10700 ΩR_p = \frac{R_2 R_3}{R_2 + R_3} = 6000\ \Omega \implies R_{\text{eq}} = R_1 + R_p = 4700\ \Omega + 6000\ \Omega = 10700\ \Omega

    The problem states that R2R_2 and R3R_3 form a parallel pair connected in series with R1R_1. You added all three resistances as if they were in a single series loop.

  3. Step 3

    I=VRtotal=3.3029700=1.111×10−4 A  ⟹  I=111 μAI = \frac{V}{R_{\text{total}}} = \frac{3.30}{29700} = 1.111 \times 10^{-4}\text{ A} \implies I = 111\ \mu\text{A}

    Correct

    Itotal=VReq=3.30 V10700 Ω≈308 μAI_{\text{total}} = \frac{V}{R_{\text{eq}}} = \frac{3.30\text{ V}}{10700\ \Omega} \approx 308\ \mu\text{A}

    Your application of Ohm's law and conversion to microamperes were mathematically sound, but the numerical result was affected by your earlier overestimation of the total resistance.

  4. Step 4

    P=V×I=3.30×1.111×10−4=3.667×10−4 W  ⟹  E=P×t=3.667×10−4×2.50×10−3=9.17×10−7 J  ⟹  E=0.917 μJP = V \times I = 3.30 \times 1.111 \times 10^{-4} = 3.667 \times 10^{-4}\text{ W} \implies E = P \times t = 3.667 \times 10^{-4} \times 2.50 \times 10^{-3} = 9.17 \times 10^{-7}\text{ J} \implies E = 0.917\ \mu\text{J}

    Correct

    P=V⋅Itotal≈1.018×10−3 W  ⟹  U=P⋅Δt≈2.54 μJP = V \cdot I_{\text{total}} \approx 1.018 \times 10^{-3}\text{ W} \implies U = P \cdot \Delta t \approx 2.54\ \mu\text{J}

    You correctly computed power and energy using E=P⋅tE = P \cdot t, but the value was distorted by the incorrect current from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted all resistances from kΩ\text{k}\Omega to Ω\Omega using the metric multiplier 10310^3.

You correctly used Ohm's law I=VRI = \frac{V}{R} to relate circuit voltage to current.

You correctly calculated electrical power and energy dissipation using P=VIP = V I and E=PtE = P t.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Combination circuit misidentification

You treated a combination circuit with a parallel branch as a simple series circuit.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the structural distinction between series and parallel sub-networks, adding all resistances linearly instead of reducing the parallel branch R2∥R3R_2 \parallel R_3 to an equivalent resistance first.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify circuit topology first
  • Resistors sharing both end nodes are in parallel: Rp=(1R2+1R3)−1R_p = \left(\frac{1}{R_2} + \frac{1}{R_3}\right)^{-1}. Resistors placed sequentially on a single branch are in series: Rs=R1+R2R_s = R_1 + R_2.

  • Always sketch or highlight the junction nodes to identify parallel branches before summing resistances.

Reduce from inside out
  • In a series-parallel combination, simplify internal parallel clusters into single equivalent blocks before adding series resistors along the main path.

  • Calculate Rp=R2R3R2+R3R_p = \frac{R_2 R_3}{R_2 + R_3} first, then add R1R_1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Combine the parallel resistors R2R_2 and R3R_3: Rp=R2R3R2+R3=(10000 Ω)(15000 Ω)10000 Ω+15000 Ω=6000 ΩR_p = \frac{R_2 R_3}{R_2 + R_3} = \frac{(10000\ \Omega)(15000\ \Omega)}{10000\ \Omega + 15000\ \Omega} = 6000\ \Omega.

  2. Add the series resistor R1R_1 to find the total equivalent resistance: Req=R1+Rp=4700 Ω+6000 Ω=10700 ΩR_{\text{eq}} = R_1 + R_p = 4700\ \Omega + 6000\ \Omega = 10700\ \Omega.

  3. Calculate total current entering the parallel sub-network: I=VReq=3.30 V10700 Ω≈3.084×10−4 A=308 μAI = \frac{V}{R_{\text{eq}}} = \frac{3.30\text{ V}}{10700\ \Omega} \approx 3.084 \times 10^{-4}\text{ A} = 308\ \mu\text{A}.

  4. Calculate energy consumed over Δt=2.50 ms\Delta t = 2.50\text{ ms}: U=V⋅I⋅Δt=(3.30 V)(3.084×10−4 A)(2.50×10−3 s)≈2.54×10−6 J=2.54 μJU = V \cdot I \cdot \Delta t = (3.30\text{ V})(3.084 \times 10^{-4}\text{ A})(2.50 \times 10^{-3}\text{ s}) \approx 2.54 \times 10^{-6}\text{ J} = 2.54\ \mu\text{J}.

Final answer

I=308 μAI = 308\ \mu\text{A}, U=2.54 μJU = 2.54\ \mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing schematic diagrams from word descriptions to spot branch junctions.

  • Review the product-over-sum formula for two parallel resistors.

  • Perform a sanity check: the equivalent resistance of a parallel pair is always smaller than the smallest individual resistor in that pair.

OverviewACEpath Teacher's Diagnosis

02 The student adds the parallel resistances directly as R_p = 1/R₂ + 1/R₃ instead of taking the reciprocal of the sum of reciprocals, resulting in an erroneous equivalent resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    R1=4700 ΩR_1 = 4700\ \Omega, R2=10000 ΩR_2 = 10000\ \Omega, R3=15000 ΩR_3 = 15000\ \Omega

  2. Step 2

    Rp=110000+115000=0.00010+0.000067=0.000167 ΩR_p = \frac{1}{10000} + \frac{1}{15000} = 0.00010 + 0.000067 = 0.000167\ \Omega

    Correct

    1Rp=110000 Ω+115000 Ω  ⟹  Rp=10000×1500010000+15000 Ω=6000 Ω\frac{1}{R_p} = \frac{1}{10000\ \Omega} + \frac{1}{15000\ \Omega} \implies R_p = \frac{10000 \times 15000}{10000 + 15000}\ \Omega = 6000\ \Omega

    The formula for resistors in parallel is 1Rp=1R2+1R3\frac{1}{R_p} = \frac{1}{R_2} + \frac{1}{R_3}, not Rp=1R2+1R3R_p = \frac{1}{R_2} + \frac{1}{R_3}. You evaluated the sum of reciprocals (0.000167 Ω−10.000167\ \Omega^{-1}) but forgot to take the reciprocal 10.000167=6000 Ω\frac{1}{0.000167} = 6000\ \Omega.

  3. Step 3

    Rtotal=4700+0.000167=4700 ΩR_{\text{total}} = 4700 + 0.000167 = 4700\ \Omega

    Correct

    Req=R1+Rp=4700 Ω+6000 Ω=10700 ΩR_{\text{eq}} = R_1 + R_p = 4700\ \Omega + 6000\ \Omega = 10700\ \Omega

    You added your parallel resistance to the series resistor correctly, but your result is incorrect because RpR_p was computed incorrectly in Step 2.

  4. Step 4

    I=3.304700=7.02×10−4 A=702 μAI = \frac{3.30}{4700} = 7.02 \times 10^{-4}\ \text{A} = 702\ \mu\text{A}

    Correct

    Itotal=VReq=3.30 V10700 Ω≈3.08×10−4 A=308 μAI_{\text{total}} = \frac{V}{R_{\text{eq}}} = \frac{3.30\ \text{V}}{10700\ \Omega} \approx 3.08 \times 10^{-4}\ \text{A} = 308\ \mu\text{A}

    You applied Ohm's law I=VRI = \frac{V}{R} and converted to microamperes correctly, but used the incorrect total resistance from Step 3.

  5. Step 5

    P=V×I=3.30×7.02×10−4=2.317×10−3 W  ⟹  E=P×t=2.317×10−3×2.50×10−3=5.79×10−6 J=5.79 μJP = V \times I = 3.30 \times 7.02 \times 10^{-4} = 2.317 \times 10^{-3}\ \text{W} \implies E = P \times t = 2.317 \times 10^{-3} \times 2.50 \times 10^{-3} = 5.79 \times 10^{-6}\ \text{J} = 5.79\ \mu\text{J}

    Correct

    P=V⋅Itotal=3.30 V×3.0841×10−4 A≈1.018×10−3 W  ⟹  U=P⋅Δt=(1.018×10−3 W)(2.50×10−3 s)≈2.54 μJP = V \cdot I_{\text{total}} = 3.30\ \text{V} \times 3.0841 \times 10^{-4}\ \text{A} \approx 1.018 \times 10^{-3}\ \text{W} \implies U = P \cdot \Delta t = (1.018 \times 10^{-3}\ \text{W})(2.50 \times 10^{-3}\ \text{s}) \approx 2.54\ \mu\text{J}

    You used the correct power and energy formulas P=VIP = VI and E=PtE = Pt, but the numeric result is affected by the earlier current error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted all given values into standard SI units.

You correctly recognized that the series resistor adds directly to the parallel sub-network equivalent resistance.

You used Ohm's law and energy relations correctly throughout your solution.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted reciprocal in parallel resistance

You wrote Rp=1R2+1R3R_p = \frac{1}{R_2} + \frac{1}{R_3} instead of 1Rp=1R2+1R3\frac{1}{R_p} = \frac{1}{R_2} + \frac{1}{R_3}, forgetting to take the reciprocal after summing.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the conductance/reciprocal form 1Rp\frac{1}{R_p} with the equivalent resistance RpR_p itself. When summing reciprocals, the intermediate result has units of siemens (Ω−1\Omega^{-1}), which must be inverted to obtain ohms (Ω\Omega).

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel Resistor Formula
  • For two resistors in parallel, 1Rp=1R2+1R3\frac{1}{R_p} = \frac{1}{R_2} + \frac{1}{R_3}, or equivalently Rp=R2R3R2+R3R_p = \frac{R_2 R_3}{R_2 + R_3}.

  • Always double-check that your final step inverts the sum of reciprocals, or use the product-over-sum formula directly for two parallel branches.

Sanity Check for Parallel Combinations
  • The equivalent resistance of any parallel network must always be strictly less than the smallest individual resistor in that parallel branch, but never near zero unless one branch is a short circuit.

  • Check that Rp<min⁡(R2,R3)R_p < \min(R_2, R_3) and that its order of magnitude is comparable to the individual resistors (e.g., 10 kΩ∥15 kΩ=6 kΩ10\text{ k}\Omega \parallel 15\text{ k}\Omega = 6\text{ k}\Omega, not 0.000167 Ω0.000167\ \Omega).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the parallel equivalent resistance: Rp=R2R3R2+R3=(10000 Ω)(15000 Ω)10000 Ω+15000 Ω=1.50×10825000 Ω=6000 ΩR_p = \frac{R_2 R_3}{R_2 + R_3} = \frac{(10000\ \Omega)(15000\ \Omega)}{10000\ \Omega + 15000\ \Omega} = \frac{1.50 \times 10^8}{25000}\ \Omega = 6000\ \Omega.

  2. Calculate the total circuit resistance: Req=R1+Rp=4700 Ω+6000 Ω=10700 ΩR_{\text{eq}} = R_1 + R_p = 4700\ \Omega + 6000\ \Omega = 10700\ \Omega.

  3. Calculate the current entering the parallel network (which equals the total source current): Itotal=VReq=3.30 V10700 Ω≈3.0841×10−4 A=308 μAI_{\text{total}} = \frac{V}{R_{\text{eq}}} = \frac{3.30\ \text{V}}{10700\ \Omega} \approx 3.0841 \times 10^{-4}\ \text{A} = 308\ \mu\text{A}.

  4. Calculate total electrical power: P=V⋅Itotal=(3.30 V)(3.0841×10−4 A)≈1.0178×10−3 WP = V \cdot I_{\text{total}} = (3.30\ \text{V})(3.0841 \times 10^{-4}\ \text{A}) \approx 1.0178 \times 10^{-3}\ \text{W}.

  5. Calculate total energy consumed in Δt=2.50×10−3 s\Delta t = 2.50 \times 10^{-3}\ \text{s}: U=P⋅Δt=(1.0178×10−3 W)(2.50×10−3 s)≈2.54×10−6 J=2.54 μJU = P \cdot \Delta t = (1.0178 \times 10^{-3}\ \text{W})(2.50 \times 10^{-3}\ \text{s}) \approx 2.54 \times 10^{-6}\ \text{J} = 2.54\ \mu\text{J}.

Final answer

Itotal=308 μAI_{\text{total}} = 308\ \mu\text{A}, U=2.54 μJU = 2.54\ \mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the product-over-sum shortcut Rp=R1R2R1+R2R_p = \frac{R_1 R_2}{R_1 + R_2} for two parallel branches to avoid reciprocal errors.

  • Perform a quick unit and magnitude check: parallel equivalent resistance must be smaller than each branch resistor but remain on the same general order of magnitude.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to convert the time from milliseconds to seconds, leading to an energy value that is three orders of magnitude too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R1=4700 ΩR_1 = 4700\ \Omega, R2=10000 ΩR_2 = 10000\ \Omega, R3=15000 ΩR_3 = 15000\ \Omega

  2. Step 2

    1Rp=110000+115000=16000  ⟹  Rp=6000 Ω  ⟹  Rtotal=4700+6000=10700 Ω\frac{1}{R_p} = \frac{1}{10000} + \frac{1}{15000} = \frac{1}{6000} \implies R_p = 6000\ \Omega \implies R_{\text{total}} = 4700 + 6000 = 10700\ \Omega

  3. Step 3

    I=3.3010700=3.084×10−4 A=308.4 μAI = \frac{3.30}{10700} = 3.084 \times 10^{-4}\text{ A} = 308.4\ \mu\text{A}

  4. Step 4

    P=V×I=3.30×3.084×10−4=1.018×10−3 WP = V \times I = 3.30 \times 3.084 \times 10^{-4} = 1.018 \times 10^{-3}\text{ W}

  5. Step 5

    E=P×t=1.018×10−3×2.50=2.545×10−3 J  ⟹  E=2545 μJE = P \times t = 1.018 \times 10^{-3} \times 2.50 = 2.545 \times 10^{-3}\text{ J} \implies E = 2545\ \mu\text{J}

    Correct

    U=P⋅Δt=(1.018×10−3 W)⋅(2.50×10−3 s)≈2.54×10−6 J=2.54 μJU = P \cdot \Delta t = (1.018 \times 10^{-3}\text{ W}) \cdot (2.50 \times 10^{-3}\text{ s}) \approx 2.54 \times 10^{-6}\text{ J} = 2.54\ \mu\text{J}

    You substituted t=2.50t = 2.50 instead of converting 2.50 ms2.50\text{ ms} into base SI units (2.50×10−3 s2.50 \times 10^{-3}\text{ s}). Because the watt is J/s\text{J}/\text{s}, the time parameter must be expressed in seconds.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the resistor ratings from kilohms to standard ohms.

You combined parallel and series branches accurately to establish the total circuit resistance.

You used Ohm's law to obtain the current entering the parallel section in microamperes.

You applied the electric power relation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time Unit Conversion

You substituted the numeric value 2.502.50 directly for time without multiplying by 10−310^{-3} to change milliseconds into seconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inconsistent unit tracking during formula substitution. Base SI formulas like E=P⋅tE = P \cdot t require time in seconds when power is in watts (1 W=1 J/s1\text{ W} = 1\text{ J/s}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Units to Base Definitions
  • 1 W=1 J/s1\text{ W} = 1\text{ J}/\text{s}, which requires time tt to be in seconds (s\text{s}) to yield energy in joules (J\text{J}).

  • Always write explicit unit labels next to each numerical substitution before multiplying: (1.018×10−3 W)×(2.50×10−3 s)(1.018 \times 10^{-3}\text{ W}) \times (2.50 \times 10^{-3}\text{ s}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the given time interval to SI base units: Δt=2.50 ms=2.50×10−3 s\Delta t = 2.50\text{ ms} = 2.50 \times 10^{-3}\text{ s}.

  2. Compute total energy in joules: U=P⋅Δt=(1.018×10−3 W)⋅(2.50×10−3 s)=2.545×10−6 JU = P \cdot \Delta t = (1.018 \times 10^{-3}\text{ W}) \cdot (2.50 \times 10^{-3}\text{ s}) = 2.545 \times 10^{-6}\text{ J}.

  3. Convert the calculated energy to microjoules: 2.545×10−6 J×106 μJ1 J≈2.54 μJ2.545 \times 10^{-6}\text{ J} \times \frac{10^6\ \mu\text{J}}{1\text{ J}} \approx 2.54\ \mu\text{J}.

Final answer

Itotal=308 μAI_{\text{total}} = 308\ \mu\text{A}; U=2.54 μJU = 2.54\ \mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out all given quantities in SI base units in an initial data column before solving equations.

  • Check that compound units cancel cleanly (for example, W⋅s=(J/s)⋅s=J\text{W} \cdot \text{s} = (\text{J}/\text{s}) \cdot \text{s} = \text{J}).

  • Practice converting metric prefix scale factors (milli- to micro-) to quickly verify the order of magnitude of your final answer.

Lock it in

Similar question

01

A 5.0 V5.0\text{ V} source is connected to a series resistor R1=2.0 kΩR_1 = 2.0\text{ k}\Omega followed by a parallel pair of identical resistors R2=R3=6.0 kΩR_2 = R_3 = 6.0\text{ k}\Omega. Determine the total equivalent resistance and the total source current in milliamperes.

Answer

Req=5.0 kΩR_{\text{eq}} = 5.0\text{ k}\Omega, Itotal=1.0 mAI_{\text{total}} = 1.0\text{ mA}. Steps: Rp=6.0×6.06.0+6.0=3.0 kΩR_p = \frac{6.0 \times 6.0}{6.0 + 6.0} = 3.0\text{ k}\Omega; Req=R1+Rp=2.0+3.0=5.0 kΩR_{\text{eq}} = R_1 + R_p = 2.0 + 3.0 = 5.0\text{ k}\Omega; I=5.0 V5.0 kΩ=1.0 mAI = \frac{5.0\text{ V}}{5.0\text{ k}\Omega} = 1.0\text{ mA}.

02

A circuit consists of a DC source V=12.0 VV = 12.0\text{ V} powering R1=1.0 kΩR_1 = 1.0\text{ k}\Omega in series with a parallel combination of R2=3.0 kΩR_2 = 3.0\text{ k}\Omega and R3=6.0 kΩR_3 = 6.0\text{ k}\Omega. Calculate the current flowing specifically through resistor R2R_2 in milliamperes.

Answer

I2=2.67 mAI_2 = 2.67\text{ mA}. Steps: Rp=3.0×6.03.0+6.0=2.0 kΩR_p = \frac{3.0 \times 6.0}{3.0 + 6.0} = 2.0\text{ k}\Omega; Req=1.0+2.0=3.0 kΩR_{\text{eq}} = 1.0 + 2.0 = 3.0\text{ k}\Omega; Itotal=12.0 V3.0 kΩ=4.0 mAI_{\text{total}} = \frac{12.0\text{ V}}{3.0\text{ k}\Omega} = 4.0\text{ mA}; voltage across parallel pair is Vp=ItotalRp=(4.0 mA)(2.0 kΩ)=8.0 VV_p = I_{\text{total}} R_p = (4.0\text{ mA})(2.0\text{ k}\Omega) = 8.0\text{ V}; I2=VpR2=8.0 V3.0 kΩ≈2.67 mAI_2 = \frac{V_p}{R_2} = \frac{8.0\text{ V}}{3.0\text{ k}\Omega} \approx 2.67\text{ mA}.

03

A micro-sensor network powered by 3.0 V3.0\text{ V} has a series resistor R1=500 ΩR_1 = 500\ \Omega followed by three parallel branches: R2=2.0 kΩR_2 = 2.0\text{ k}\Omega, R3=3.0 kΩR_3 = 3.0\text{ k}\Omega, and R4=6.0 kΩR_4 = 6.0\text{ k}\Omega. Find the total electrical energy consumed by the circuit in 10.0 ms10.0\text{ ms} in microjoules.

Answer

U=60.0 μJU = 60.0\ \mu\text{J}. Steps: 1Rp=12000+13000+16000=3+2+16000=66000  ⟹  Rp=1000 Ω\frac{1}{R_p} = \frac{1}{2000} + \frac{1}{3000} + \frac{1}{6000} = \frac{3 + 2 + 1}{6000} = \frac{6}{6000} \implies R_p = 1000\ \Omega; Req=R1+Rp=500+1000=1500 ΩR_{\text{eq}} = R_1 + R_p = 500 + 1000 = 1500\ \Omega; P=V2Req=(3.0)21500=0.006 WP = \frac{V^2}{R_{\text{eq}}} = \frac{(3.0)^2}{1500} = 0.006\text{ W}; U=PΔt=(0.006 W)(0.010 s)=60.0×10−6 J=60.0 μJU = P \Delta t = (0.006\text{ W})(0.010\text{ s}) = 60.0 \times 10^{-6}\text{ J} = 60.0\ \mu\text{J}.

Loading workspace…