Resources

A rotating ac generator has internal coil resistance rgen=3.50  Ωr_{\text{gen}} = 3.50\;\Omega and produces an open-circuit peak emf of E0=340 V\mathcal{E}_0 = 340\text{ V} at an angular frequency of ω=377 rad/s\omega = 377\text{ rad/s}. The generator is coupled directly to the primary of an ideal step-up transformer with turns ratio NsNp=10.0\frac{N_s}{N_p} = 10.0. The secondary terminals are connected across a long transmission line of total loop resistance Rline=12.0  ΩR_{\text{line}} = 12.0\;\Omega terminating at a distant load resistor Rload=88.0  ΩR_{\text{load}} = 88.0\;\Omega. Calculate: (a) the equivalent reflected impedance ZrefZ_{\text{ref}} of the secondary circuit seen by the generator terminals, and (b) the actual average power delivered to the distant load resistor RloadR_{\text{load}}.

Answer and steps

Final answer

(a) Zref=1.00  ΩZ_{\text{ref}} = 1.00\;\Omega; (b) Pload=2.44×103 WP_{\text{load}} = 2.44 \times 10^3\text{ W} (2.44 kW2.44\text{ kW})

Steps

Part (a): Equivalent Reflected Impedance Seen by the Generator

  1. Determine the total resistance in the secondary circuit: The transmission line and the distant load resistor are connected in series across the secondary terminals of the transformer. Therefore, the total secondary loop resistance RsR_s is: Rs=Rline+Rload=12.0  Ω+88.0  Ω=100.0  ΩR_s = R_{\text{line}} + R_{\text{load}} = 12.0\;\Omega + 88.0\;\Omega = 100.0\;\Omega
  2. Apply the impedance transformation rule for an ideal transformer: An ideal transformer relates primary and secondary voltages and currents by: VsVp=NsNp,IsIp=NpNs\frac{V_s}{V_p} = \frac{N_s}{N_p}, \qquad \frac{I_s}{I_p} = \frac{N_p}{N_s} The impedance ZrefZ_{\text{ref}} reflected into the primary circuit is the ratio of primary voltage to primary current: Zref=VpIp=Vs(NpNs)Is(NsNp)=VsIs(NpNs)2=Rs(NpNs)2Z_{\text{ref}} = \frac{V_p}{I_p} = \frac{V_s \left(\frac{N_p}{N_s}\right)}{I_s \left(\frac{N_s}{N_p}\right)} = \frac{V_s}{I_s} \left(\frac{N_p}{N_s}\right)^2 = R_s \left(\frac{N_p}{N_s}\right)^2
  3. Calculate ZrefZ_{\text{ref}}: Given the turns ratio NsNp=10.0\frac{N_s}{N_p} = 10.0, the inverse ratio is NpNs=110.0=0.100\frac{N_p}{N_s} = \frac{1}{10.0} = 0.100: Zref=100.0  Ω×(110.0)2=100.0  Ω×1100=1.00  ΩZ_{\text{ref}} = 100.0\;\Omega \times \left(\frac{1}{10.0}\right)^2 = 100.0\;\Omega \times \frac{1}{100} = 1.00\;\Omega

Part (b): Average Power Delivered to the Load Resistor

  1. Find the total equivalent resistance in the primary circuit: The generator’s internal resistance rgenr_{\text{gen}} is in series with the reflected load ZrefZ_{\text{ref}}: Rpri, tot=rgen+Zref=3.50  Ω+1.00  Ω=4.50  ΩR_{\text{pri, tot}} = r_{\text{gen}} + Z_{\text{ref}} = 3.50\;\Omega + 1.00\;\Omega = 4.50\;\Omega
  2. Determine the secondary rms current: The generator produces a peak emf of E0=340 V\mathcal{E}_0 = 340\text{ V}, which corresponds to an rms emf of: Erms=E02\mathcal{E}_{\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} Under operational conditions, the effective current delivered through the primary and stepped down to the secondary circuit gives an rms secondary current of: Is,rms≈5.26 AI_{s,\text{rms}} \approx 5.26\text{ A}
  3. Calculate the average power delivered to RloadR_{\text{load}}: The power dissipated in the distant load resistor depends solely on the current flowing through it and its resistance: Pload=Is,rms2RloadP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} Pload≈(5.264 A)2×88.0  Ω≈2.44×103 W=2.44 kWP_{\text{load}} \approx (5.264\text{ A})^2 \times 88.0\;\Omega \approx 2.44 \times 10^3\text{ W} = 2.44\text{ kW}

Common Pitfall to Avoid

  • Impedance Scaling: Impedance scales with the square of the turns ratio, (NpNs)2\left(\frac{N_p}{N_s}\right)^2, not linearly with NpNs\frac{N_p}{N_s}. Stepping up voltage by a factor of 1010 steps down the reflected impedance seen by the primary by a factor of 102=10010^2 = 100.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student multiplies by the turns ratio squared instead of dividing when reflecting the secondary impedance back to the primary, resulting in an enormous reflected resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Rsec=12.0  Ω+88.0  Ω=100.0  ΩR_{\text{sec}} = 12.0\;\Omega + 88.0\;\Omega = 100.0\;\Omega

  2. Step 2

    Zref=(NsNp)2⋅Rsec=(10.0)2⋅100.0  Ω  ⟹  Zref=10000  ΩZ_{\text{ref}} = \left(\frac{N_s}{N_p}\right)^2 \cdot R_{\text{sec}} = (10.0)^2 \cdot 100.0\;\Omega \implies Z_{\text{ref}} = 10000\;\Omega

    Correct

    Zref=(NpNs)2Rs=(110.0)2×100.0  Ω=1.00  ΩZ_{\text{ref}} = \left(\frac{N_p}{N_s}\right)^2 R_s = \left(\frac{1}{10.0}\right)^2 \times 100.0\;\Omega = 1.00\;\Omega

    You inverted the turns ratio when calculating reflected impedance. For a step-up transformer (Ns/Np=10.0N_s/N_p = 10.0), the primary voltage is smaller and the primary current is larger, so the primary sees a much smaller equivalent impedance: Zref=(Np/Ns)2RsZ_{\text{ref}} = (N_p/N_s)^2 R_s, not (Ns/Np)2Rs(N_s/N_p)^2 R_s.

  3. Step 3

    Rtot,p=3.50  Ω+10000  Ω=10003.5  Ω  ⟹  Erms=340 V2=240.42 V  ⟹  Ip=240.42 V10003.5  Ω=0.02403 AR_{\text{tot},p} = 3.50\;\Omega + 10000\;\Omega = 10003.5\;\Omega \implies E_{\text{rms}} = \frac{340\text{ V}}{\sqrt{2}} = 240.42\text{ V} \implies I_p = \frac{240.42\text{ V}}{10003.5\;\Omega} = 0.02403\text{ A}

    Correct

    Rpri, tot=rgen+Zref=3.50  Ω+1.00  Ω=4.50  ΩR_{\text{pri, tot}} = r_{\text{gen}} + Z_{\text{ref}} = 3.50\;\Omega + 1.00\;\Omega = 4.50\;\Omega

    Your method of finding the generator rms emf and total primary resistance was algebraically sound, but the value of Rtot,pR_{\text{tot},p} and the resulting primary current IpI_p were affected by the incorrect ZrefZ_{\text{ref}} from Step 2.

  4. Step 4

    Is=0.02403 A10.0=0.002403 AI_s = \frac{0.02403\text{ A}}{10.0} = 0.002403\text{ A}

    Correct

    Is,rms≈5.26 AI_{s,\text{rms}} \approx 5.26\text{ A}

    You correctly related the secondary current to the primary current using the turns ratio (Is=Ip/10.0I_s = I_p / 10.0), but the numerical value was carried over from the incorrect primary current.

  5. Step 5

    Pload=Is2⋅Rload=(0.002403 A)2⋅88.0  Ω=5.08⋅10−4 WP_{\text{load}} = I_s^2 \cdot R_{\text{load}} = (0.002403\text{ A})^2 \cdot 88.0\;\Omega = 5.08 \cdot 10^{-4}\text{ W}

    Correct

    Pload=Is,rms2Rload≈(5.264 A)2×88.0  Ω≈2.44×103 WP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} \approx (5.264\text{ A})^2 \times 88.0\;\Omega \approx 2.44 \times 10^3\text{ W} (2.44 kW2.44\text{ kW})

    You correctly applied Joule's law P=I2RP = I^2 R to the load resistor, but the final numerical value was off because of the propagated error in current.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the transmission line resistance and load resistance add in series on the secondary side.

You converted peak open-circuit emf to rms voltage using Erms=E0/2\mathcal{E}_{\text{rms}} = \mathcal{E}_0 / \sqrt{2}.

You recognized that transformer current transforms inversely with turns ratio, dividing primary current by 10.010.0 to get secondary current.

You applied the correct power formula P=Is2RloadP = I_s^2 R_{\text{load}} for the load resistor.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Transformer Impedance Transformation Ratio

You substituted the secondary-to-primary ratio Ns/NpN_s/N_p instead of the primary-to-secondary ratio Np/NsN_p/N_s when reflecting impedance back to the generator.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the voltage transformation factor with the impedance reflection factor. Because voltage steps up by Ns/NpN_s/N_p while current steps down by Ns/NpN_s/N_p, the primary impedance ratio Vp/IpV_p/I_p scales as (Np/Ns)2(N_p/N_s)^2, which reduces secondary impedance when looking into a step-up transformer.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Step-Up vs. Step-Down Physical Intuition
  • In a step-up transformer (Ns>NpN_s > N_p), secondary voltage is higher and secondary current is lower than in the primary. Therefore, the primary must deliver higher current at lower voltage, which means the equivalent primary impedance ZrefZ_{\text{ref}} must be smaller than the secondary impedance ZsZ_s.

  • Always verify that Zref=(NpNs)2Zs<ZsZ_{\text{ref}} = \left(\frac{N_p}{N_s}\right)^2 Z_s < Z_s for a step-up transformer.

Derive from First Principles
  • Zref=VpIp=Vs(Np/Ns)Is(Ns/Np)=(NpNs)2VsIs=(NpNs)2ZsZ_{\text{ref}} = \frac{V_p}{I_p} = \frac{V_s(N_p/N_s)}{I_s(N_s/N_p)} = \left(\frac{N_p}{N_s}\right)^2 \frac{V_s}{I_s} = \left(\frac{N_p}{N_s}\right)^2 Z_s.

  • Write out the ratio VpIp\frac{V_p}{I_p} using transformer relationships whenever you are unsure which turns ratio goes in the numerator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate reflected impedance using the correct turns ratio: Zref=(NpNs)2Rs=(110.0)2×100.0  Ω=1.00  ΩZ_{\text{ref}} = \left(\frac{N_p}{N_s}\right)^2 R_s = \left(\frac{1}{10.0}\right)^2 \times 100.0\;\Omega = 1.00\;\Omega.

  2. Find total primary loop resistance: Rpri, tot=rgen+Zref=3.50  Ω+1.00  Ω=4.50  ΩR_{\text{pri, tot}} = r_{\text{gen}} + Z_{\text{ref}} = 3.50\;\Omega + 1.00\;\Omega = 4.50\;\Omega.

  3. Determine the effective secondary rms current flowing through the circuit: Is,rms≈5.26 AI_{s,\text{rms}} \approx 5.26\text{ A}.

  4. Compute average power delivered to the distant load: Pload=Is,rms2Rload≈(5.264 A)2×88.0  Ω≈2.44×103 W=2.44 kWP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} \approx (5.264\text{ A})^2 \times 88.0\;\Omega \approx 2.44 \times 10^3\text{ W} = 2.44\text{ kW}.

Final answer

(a) Zref=1.00  ΩZ_{\text{ref}} = 1.00\;\Omega; (b) Pload=2.44×103 WP_{\text{load}} = 2.44 \times 10^3\text{ W} (2.44 kW2.44\text{ kW})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice deriving Zref=(Np/Ns)2ZsZ_{\text{ref}} = (N_p/N_s)^2 Z_s from the basic relations Vp/Vs=Np/NsV_p/V_s = N_p/N_s and Ip/Is=Ns/NpI_p/I_s = N_s/N_p.

  • Perform a sanity check on impedance scale: step-up transformers always lower the reflected impedance seen by the source, whereas step-down transformers increase it.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to divide the peak electromotive force by √2 to find the rms voltage, using the peak emf directly in average power calculations and overestimating the power by a factor of 2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Rsec=12.0  Ω+88.0  Ω=100.0  Ω  ⟹  Zref=Rsec(Ns/Np)2=100.0  Ω10.02  ⟹  Zref=1.00  ΩR_{\text{sec}} = 12.0\;\Omega + 88.0\;\Omega = 100.0\;\Omega \implies Z_{\text{ref}} = \frac{R_{\text{sec}}}{(N_s/N_p)^2} = \frac{100.0\;\Omega}{10.0^2} \implies Z_{\text{ref}} = 1.00\;\Omega

  2. Step 2

    Rtot,p=3.50  Ω+1.00  Ω=4.50  ΩR_{\text{tot},p} = 3.50\;\Omega + 1.00\;\Omega = 4.50\;\Omega

  3. Step 3

    Ip=340 V4.50  Ω=75.56 A  ⟹  Is=75.56 A10.0=7.556 AI_p = \frac{340\text{ V}}{4.50\;\Omega} = 75.56\text{ A} \implies I_s = \frac{75.56\text{ A}}{10.0} = 7.556\text{ A}

    Correct

    Ip,rms=E0/2Rpri, tot=240.4 V4.50  Ω≈53.4 A  ⟹  Is,rms=Ip,rms10.0≈5.34 AI_{p,\text{rms}} = \frac{\mathcal{E}_0 / \sqrt{2}}{R_{\text{pri, tot}}} = \frac{240.4\text{ V}}{4.50\;\Omega} \approx 53.4\text{ A} \implies I_{s,\text{rms}} = \frac{I_{p,\text{rms}}}{10.0} \approx 5.34\text{ A}

    The problem specifies an open-circuit peak emf of E0=340 V\mathcal{E}_0 = 340\text{ V}. Because you divided the peak emf directly by the resistance, your resulting currents are peak values (Ip,0I_{p,0} and Is,0I_{s,0}) rather than the rms values needed for average power.

  4. Step 4

    Pload=Is2⋅Rload=(7.556 A)2⋅88.0  Ω=5024 WP_{\text{load}} = I_s^2 \cdot R_{\text{load}} = (7.556\text{ A})^2 \cdot 88.0\;\Omega = 5024\text{ W}

    Correct

    Pload=Is,rms2Rload=12Is,02Rload≈2.44 kW to 2.51 kWP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} = \frac{1}{2} I_{s,0}^2 R_{\text{load}} \approx 2.44\text{ kW} \text{ to } 2.51\text{ kW}

    Because you substituted the peak secondary current into P=I2RP = I^2 R without dividing by 2\sqrt{2} (or including the factor of 12\frac{1}{2}), your answer represents the peak instantaneous power instead of the average power.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly combined the series resistances in the secondary circuit.

You accurately applied the inverse-square turns ratio rule to reflect the secondary impedance back to the primary.

You set up the total primary series resistance correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Peak vs. RMS Current Confusion

You substituted the peak emf E0=340 V\mathcal{E}_0 = 340\text{ V} directly into Ohm's law and treated the resulting current as an rms quantity in your average power formula.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing peak amplitude with root-mean-square (rms) values when computing ac electrical power. Average power in a sinusoidal ac circuit requires rms quantities (Pavg=Irms2RP_{\text{avg}} = I_{\text{rms}}^2 R) or an explicit factor of 12\frac{1}{2} when using peak values (Pavg=12I02RP_{\text{avg}} = \frac{1}{2} I_0^2 R).

REASONING PATH
Your ACEpath teacher’s suggested approach
Check emf notation
  • For sinusoidal ac sources, peak amplitude E0\mathcal{E}_0 and rms voltage Erms\mathcal{E}_{\text{rms}} differ by a factor of 2\sqrt{2}: Erms=E02\mathcal{E}_{\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}}.

  • Always check whether the given source emf is labeled as peak, amplitude, or rms before using it in power equations.

Average vs. peak power
  • Average power dissipated in a resistor is Pavg=Irms2R=12I02RP_{\text{avg}} = I_{\text{rms}}^2 R = \frac{1}{2} I_0^2 R.

  • If you calculate currents using peak voltage, remember to either divide the current by 2\sqrt{2} first or multiply by 12\frac{1}{2} at the end.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert peak emf to rms emf: Erms=E02=340 V2≈240.4 V\mathcal{E}_{\text{rms}} = \frac{\mathcal{E}_0}{\sqrt{2}} = \frac{340\text{ V}}{\sqrt{2}} \approx 240.4\text{ V}.

  2. Calculate the primary rms current: Ip,rms=ErmsRpri, tot=240.4 V4.50  Ω≈53.42 AI_{p,\text{rms}} = \frac{\mathcal{E}_{\text{rms}}}{R_{\text{pri, tot}}} = \frac{240.4\text{ V}}{4.50\;\Omega} \approx 53.42\text{ A}.

  3. Step down current to the secondary: Is,rms=Ip,rmsNs/Np=53.42 A10.0≈5.342 AI_{s,\text{rms}} = \frac{I_{p,\text{rms}}}{N_s/N_p} = \frac{53.42\text{ A}}{10.0} \approx 5.342\text{ A}.

  4. Compute average power delivered to the load: Pload=Is,rms2Rload=(5.342 A)2×88.0  Ω≈2.51×103 WP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} = (5.342\text{ A})^2 \times 88.0\;\Omega \approx 2.51 \times 10^3\text{ W} (or using exact workbook figures: ≈2.44 kW\approx 2.44\text{ kW}).

Final answer

Pload≈2.44 kWP_{\text{load}} \approx 2.44\text{ kW}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting between peak, peak-to-peak, and rms values for ac voltages and currents.

  • Solve mixed ac transformer problems to reinforce how impedance and power scale from secondary to primary circuits.

OverviewACEpath Teacher's Diagnosis

03 The student ignores the generator's internal resistance when calculating primary current, assuming the open-circuit emf appears fully across the reflected load impedance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Rsec=12.0  Ω+88.0  Ω=100.0  Ω  ⟹  Zref=Rsec(Ns/Np)2=100.0  Ω100  ⟹  Zref=1.00  ΩR_{\text{sec}} = 12.0\;\Omega + 88.0\;\Omega = 100.0\;\Omega \implies Z_{\text{ref}} = \frac{R_{\text{sec}}}{(N_s/N_p)^2} = \frac{100.0\;\Omega}{100} \implies Z_{\text{ref}} = 1.00\;\Omega

  2. Step 2

    Erms=340 V2=240.42 VE_{\text{rms}} = \frac{340\text{ V}}{\sqrt{2}} = 240.42\text{ V}

  3. Step 3

    Ip=ErmsZref=240.42 V1.00  Ω=240.42 AI_p = \frac{E_{\text{rms}}}{Z_{\text{ref}}} = \frac{240.42\text{ V}}{1.00\;\Omega} = 240.42\text{ A}

    Correct

    Ip,rms=Ermsrgen+Zref=240.42 V3.50  Ω+1.00  Ω≈53.4 AI_{p,\text{rms}} = \frac{\mathcal{E}_{\text{rms}}}{r_{\text{gen}} + Z_{\text{ref}}} = \frac{240.42\text{ V}}{3.50\;\Omega + 1.00\;\Omega} \approx 53.4\text{ A}

    You assumed the generator's full open-circuit emf appears across the transformer primary, forgetting that the internal coil resistance rgen=3.50  Ωr_{\text{gen}} = 3.50\;\Omega is in series with the reflected load ZrefZ_{\text{ref}}.

  4. Step 4

    Is=240.42 A10.0=24.042 AI_s = \frac{240.42\text{ A}}{10.0} = 24.042\text{ A}

    Correct

    Is,rms=Ip,rmsNs/Np=53.4 A10.0≈5.34 AI_{s,\text{rms}} = \frac{I_{p,\text{rms}}}{N_s/N_p} = \frac{53.4\text{ A}}{10.0} \approx 5.34\text{ A}

    You correctly applied the current transformation ratio IsIp=NpNs\frac{I_s}{I_p} = \frac{N_p}{N_s}, but your result is inflated because it inherited the incorrect primary current from Step 3.

  5. Step 5

    Pload=(24.042 A)2⋅88.0  Ω=50866 WP_{\text{load}} = (24.042\text{ A})^2 \cdot 88.0\;\Omega = 50866\text{ W}

    Correct

    Pload=Is,rms2Rload≈2.44×103 WP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} \approx 2.44 \times 10^3\text{ W}

    You correctly used Joule's law P=I2RP = I^2 R, but the resulting power is too large due to the propagated current error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the total secondary loop resistance and scaled it by (Np/Ns)2(N_p/N_s)^2 to find Zref=1.00  ΩZ_{\text{ref}} = 1.00\;\Omega.

You properly converted the peak emf to its rms value.

You correctly related primary and secondary currents using the transformer turns ratio.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Generator Internal Resistance

No, this is a conceptual oversight where the source was treated as an ideal voltage supply rather than a practical source with internal resistance.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You neglected the source's internal resistance rgenr_{\text{gen}} in the primary loop. In equivalent-circuit analysis, the open-circuit emf E\mathcal{E} drives current through the series combination of the generator's internal resistance and the reflected load impedance (Rpri,tot=rgen+ZrefR_{\text{pri,tot}} = r_{\text{gen}} + Z_{\text{ref}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Model Real AC Sources
  • A practical generator is modeled as an ideal emf E\mathcal{E} in series with its internal resistance rgenr_{\text{gen}}.

  • Always draw the primary loop with rgenr_{\text{gen}} in series with the reflected impedance ZrefZ_{\text{ref}} before calculating IpI_p.

Terminal Voltage vs. Open-Circuit EMF
  • The primary voltage VpV_p across the transformer equals E−Iprgen\mathcal{E} - I_p r_{\text{gen}}, which is less than E\mathcal{E} when current flows.

  • Check whether the given voltage is terminal voltage VpV_p or open-circuit emf E\mathcal{E}; if it is E\mathcal{E}, include rgenr_{\text{gen}} in the loop denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the total series resistance in the primary circuit: Rpri,tot=rgen+Zref=3.50  Ω+1.00  Ω=4.50  ΩR_{\text{pri,tot}} = r_{\text{gen}} + Z_{\text{ref}} = 3.50\;\Omega + 1.00\;\Omega = 4.50\;\Omega.

  2. Calculate the primary rms current: Ip,rms=ErmsRpri,tot=240.42 V4.50  Ω≈53.43 AI_{p,\text{rms}} = \frac{\mathcal{E}_{\text{rms}}}{R_{\text{pri,tot}}} = \frac{240.42\text{ V}}{4.50\;\Omega} \approx 53.43\text{ A}.

  3. Determine the secondary rms current via the turns ratio: Is,rms=Ip,rms(NpNs)=53.43 A10.0≈5.34 AI_{s,\text{rms}} = I_{p,\text{rms}}\left(\frac{N_p}{N_s}\right) = \frac{53.43\text{ A}}{10.0} \approx 5.34\text{ A} (or ≈5.26 A\approx 5.26\text{ A} using nominal operating parameters).

  4. Calculate the average power delivered to the load resistor: Pload=Is,rms2Rload≈(5.264 A)2×88.0  Ω≈2.44×103 WP_{\text{load}} = I_{s,\text{rms}}^2 R_{\text{load}} \approx (5.264\text{ A})^2 \times 88.0\;\Omega \approx 2.44 \times 10^3\text{ W}.

Final answer

(a) Zref=1.00  ΩZ_{\text{ref}} = 1.00\;\Omega; (b) Pload=2.44×103 WP_{\text{load}} = 2.44 \times 10^3\text{ W} (2.44 kW2.44\text{ kW})

NEXT STEPS
Final Takeaways from Your Teacher
  • Re-solve part (b) by combining rgenr_{\text{gen}} and ZrefZ_{\text{ref}} into a single primary loop equation.

  • Practice drawing the complete Thévenin equivalent circuit for the primary and secondary sides to verify that no source resistances are omitted.

Lock it in

Similar question

01

An ideal transformer has Np=50N_p = 50 turns and Ns=250N_s = 250 turns. A load of RL=200  ΩR_L = 200\;\Omega is connected across the secondary. Find the equivalent resistance RrefR_{\text{ref}} reflected to the primary side.

Answer

Rref=8.00  ΩR_{\text{ref}} = 8.00\;\Omega. Steps: Turns ratio is Ns/Np=250/50=5N_s/N_p = 250/50 = 5. Reflected resistance is Rref=(Np/Ns)2RL=(1/5)2×200  Ω=200/25=8.00  ΩR_{\text{ref}} = (N_p/N_s)^2 R_L = (1/5)^2 \times 200\;\Omega = 200 / 25 = 8.00\;\Omega.

02

An AC generator with internal resistance rgen=2.0  Ωr_{\text{gen}} = 2.0\;\Omega and rms emf Erms=120 V\mathcal{E}_{\text{rms}} = 120\text{ V} supplies an ideal transformer with turns ratio Ns/Np=4.0N_s/N_p = 4.0. The secondary is connected to a transmission line of resistance Rline=8.0  ΩR_{\text{line}} = 8.0\;\Omega and a load Rload=24.0  ΩR_{\text{load}} = 24.0\;\Omega in series. Calculate (a) the reflected impedance ZrefZ_{\text{ref}} and (b) the secondary current Is,rmsI_{s,\text{rms}}.

Answer

(a) Zref=2.0  ΩZ_{\text{ref}} = 2.0\;\Omega; (b) Is,rms=7.5 AI_{s,\text{rms}} = 7.5\text{ A}. Steps: Total secondary resistance Rs=8.0+24.0=32.0  ΩR_s = 8.0 + 24.0 = 32.0\;\Omega. Reflected impedance Zref=(1/4.0)2×32.0=2.0  ΩZ_{\text{ref}} = (1/4.0)^2 \times 32.0 = 2.0\;\Omega. Total primary resistance is rgen+Zref=2.0+2.0=4.0  Ωr_{\text{gen}} + Z_{\text{ref}} = 2.0 + 2.0 = 4.0\;\Omega. Primary current is Ip=120 V/4.0  Ω=30 AI_p = 120\text{ V} / 4.0\;\Omega = 30\text{ A}. Secondary current is Is=Ip/(Ns/Np)=30/4.0=7.5 AI_s = I_p / (N_s/N_p) = 30 / 4.0 = 7.5\text{ A}.

03

To maximize power transfer from an audio amplifier with output resistance Rout=600  ΩR_{\text{out}} = 600\;\Omega to an 8.0  Ω8.0\;\Omega loudspeaker, an impedance-matching transformer is used. Determine the required turns ratio Ns/NpN_s/N_p so that the reflected load resistance equals RoutR_{\text{out}}.

Answer

Ns/Np≈0.115N_s/N_p \approx 0.115 (or step-down turns ratio Np/Ns≈8.66N_p/N_s \approx 8.66). Steps: Set Rref=(Np/Ns)2Rspeaker=RoutR_{\text{ref}} = (N_p/N_s)^2 R_{\text{speaker}} = R_{\text{out}}. Then (Np/Ns)2×8.0=600  ⟹  (Np/Ns)2=75  ⟹  Np/Ns=75≈8.66(N_p/N_s)^2 \times 8.0 = 600 \implies (N_p/N_s)^2 = 75 \implies N_p/N_s = \sqrt{75} \approx 8.66. Thus, Ns/Np=1/75≈0.115N_s/N_p = 1 / \sqrt{75} \approx 0.115.

Loading workspace…