Resources
In a physics laboratory session, a student uses a spectrometer equipped with a transmission diffraction grating to measure the wavelength of an unknown spectral line from an emission tube. The grating is labeled as having . The central zero-order line is aligned with the spectrometer's angular scale at . The student rotates the telescope and records the position of the first-order spectral line on the left at and on the right at . Using the symmetric angular deflection to eliminate zero-offset error, determine the experimental wavelength of the emission line in nanometers.
Answer and steps
Final answer
Steps
Calculate the Grating Element ()
The grating has a ruling density of . The slit spacing (grating element) is the reciprocal of the line density:
Determine the Diffraction Angle ()
To eliminate systematic zero-offset errors, the diffraction angle is calculated using the total angular deflection between the symmetric first-order () lines on either side of the central maximum:
(Check: Measuring relative to the central zero-order gives and , confirming perfect symmetry.)
Apply the Grating Equation
The condition for constructive interference for a diffraction grating at normal incidence is:
For the first-order spectrum ():
Substitute the numerical values:
Rounding to the nearest whole integer gives:
Typical errors
01 The student uses the total angle between the two symmetric orders 2θ instead of the single diffraction angle θ in the grating equation, doubling the calculated wavelength.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You substituted the full span instead of the single diffraction angle measured from the central maximum, which is .
- Step 4Correct
Your final calculation followed correctly from the incorrect angle used in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the total angular difference between the left and right first-order spectral lines.
You correctly calculated the grating spacing by taking the reciprocal of the line density.
You correctly identified the first-order grating condition .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou labeled the difference as in your first line, but omitted dividing by before substituting into the grating equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the total angular deflection between symmetric orders () with the diffraction angle measured relative to the central normal axis ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Define the angle in the grating formula
In , the angle is measured from the central zero-order () normal axis to the -th order maximum.
Whenever you take the difference between symmetric left and right orders, remember that , so you must divide by to obtain .
CORRECTED PATH
ACEpath Teacher's Demonstration02 The student miscalculates the grating spacing by multiplying by 600 instead of inverting the grating line density.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The grating spacing is the distance between adjacent slits, which is the reciprocal of the line density , not the line density itself.
- Step 3Correct
You correctly used the first-order grating condition , but this step was affected by your incorrect value for .
- Step 4Correct
Your final numerical value propagated the miscalculated grating spacing.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the diffraction angle by halving the difference between the two symmetric first-order angular readings.
You identified and applied the correct diffraction grating formula for the first-order spectrum.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the grating ruling density (number of lines per unit length) with the grating element (spacing between adjacent slits), multiplying by the number of lines instead of inverting it to find distance per line.
REASONING PATH
Your ACEpath teacher’s suggested approach- Grating Element vs. Line Density
, where is the number of lines per unit length.
Always invert the ruling density and convert to meters: .
- Physical Sanity Check for Wavelength
Visible light wavelengths are on the order of to ().
If an optical wavelength calculation yields an answer outside (such as ), immediately check your slit spacing unit and reciprocal.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the grating element by inverting line density: .
Substitute and into the grating equation for : .
Evaluate and convert to nanometers: .
03 The student uses the small-angle approximation tan θ ≈ θ or evaluates the angle directly in degrees without taking the sine.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The diffraction grating equation requires the sine of the angle, . You used with in radians, which is only valid for very small angles (typically ). Because , , whereas , creating an overestimate.
- Step 4Correct
Your final wavelength value is inaccurate due to substituting instead of in the grating equation.
WHAT YOU DID WELL
Compliments from Your TeacherYou eliminated zero-offset errors by taking half of the symmetric deflection between the left and right first-order lines.
You accurately computed the grating element from the line density.
You maintained consistent metric unit conversions.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that the small-angle approximation holds for any angle when converted to radians, overlooking that diffraction grating angles in spectrometer experiments are frequently too large for this approximation to be valid.
REASONING PATH
Your ACEpath teacher’s suggested approach- Exact Grating Condition
For a transmission grating at normal incidence, constructive interference occurs when .
Always evaluate directly on your calculator rather than converting to radians and replacing with .
- Small-Angle Threshold
The approximation is generally acceptable only when (or ), where the discrepancy is under .
Check if . If it is, using will produce an unacceptable error in precision laboratory measurements.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the trigonometric sine of the diffraction angle: .
Substitute into the first-order grating equation (): .
Evaluate the product: .
Lock it in
In the diffraction grating equation , how is the angle defined geometrically?
is the angle between the central normal ( axis) and the diffracted ray of order .
Similar question
A transmission grating with is illuminated at normal incidence. Symmetrical first-order peaks are recorded at spectrometer angles of and . Determine the wavelength of the light in nanometers.
Answer
. Key steps: . Grating spacing . Then .
A diffraction grating with slit spacing is used to view a laser beam. The second-order () maxima on either side of the center have a total angular separation of . What is the wavelength of the laser?
Answer
. Key steps: The total angular separation across symmetric second-order maxima is . Using the grating equation for : .
A spectrometer measures the green mercury line () using a grating with . The zero-order line is offset at . Predict the recorded angular positions and of the two first-order lines.
Answer
and . Key steps: For , . With zero-offset , and .