Resources

A robotic hand grips a smooth cylindrical tool of mass m=1.60 kgm = 1.60\text{ kg} using two identical flat, vertical parallel jaw pads pressing symmetrically against opposite sides of the cylinder. The coefficient of static friction between each pad and the tool surface is μs=0.250\mu_s = 0.250. An external vertical downward pulling force PP is applied to the tool. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2: (a) Write the mathematical expression for the minimum normal clamping force NN required on each pad as a function of PP to prevent the tool from slipping. (b) Calculate the value of NN when P=0P = 0. (c) As the downward pulling force grows extremely large (P→∞P \to \infty), determine the limiting ratio lim⁡P→∞ftotalP\lim_{P \to \infty} \frac{f_{\text{total}}}{P}, where ftotalf_{\text{total}} is the total upward frictional force required for equilibrium.

Answer and steps

Final answer

(a) N=mg+P2μsN = \frac{mg + P}{2\mu_s}; (b) N=31.4 NN = 31.4\text{ N}; (c) lim⁡P→∞ftotalP=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = 1.

Steps

Part (a): Finding the Minimum Normal Force NN

  1. Identify the vertical forces acting on the tool:

    • The downward gravitational force: W=mgW = mg
    • The downward external applied force: PP
    • The upward static frictional force exerted by the left pad: f1f_1
    • The upward static frictional force exerted by the right pad: f2f_2
  2. Apply the condition for vertical translational equilibrium: For the cylinder to remain stationary, the net force in the vertical direction must be zero: ∑Fy=f1+f2−mg−P=0\sum F_y = f_1 + f_2 - mg - P = 0 ftotal=f1+f2=mg+Pf_{\text{total}} = f_1 + f_2 = mg + P
  3. Use symmetry and the condition to prevent slipping: Because the pads are identical and clamp symmetrically with equal normal forces NN, the friction is shared equally: f1=f2=ftotal2=mg+P2f_1 = f_2 = \frac{f_{\text{total}}}{2} = \frac{mg + P}{2} To prevent slipping, the required static friction on each pad must not exceed the maximum possible static friction force: f1≤fs,max⁡=μsNf_1 \le f_{s,\max} = \mu_s N Substituting for f1f_1: mg+P2≤μsN  ⟹  N≥mg+P2μs\frac{mg + P}{2} \le \mu_s N \implies N \ge \frac{mg + P}{2\mu_s} Therefore, the minimum required normal clamping force on each pad is: N=mg+P2μsN = \frac{mg + P}{2\mu_s}

(Common Pitfall: Forgetting that there are two gripping surfaces; omitting the factor of 22 doubles the required normal force unnecessarily.)


Part (b): Calculating NN when P=0P = 0

When no external pull is applied (P=0P = 0), the clamping force only needs to support the tool's weight: N=mg2μsN = \frac{mg}{2\mu_s}

Substitute the given numerical values: m=1.60 kg,g=9.80 m/s2,μs=0.250m = 1.60\text{ kg},\quad g = 9.80\text{ m/s}^2,\quad \mu_s = 0.250 N=(1.60)(9.80)2(0.250)=15.680.500=31.36 N≈31.4 NN = \frac{(1.60)(9.80)}{2(0.250)} = \frac{15.68}{0.500} = 31.36\text{ N} \approx 31.4\text{ N}


Part (c): Determining the Limiting Ratio as P→∞P \to \infty

From vertical equilibrium, the total upward friction required to hold the cylinder is: ftotal=mg+Pf_{\text{total}} = mg + P

Divide ftotalf_{\text{total}} by PP: ftotalP=mg+PP=mgP+1\frac{f_{\text{total}}}{P} = \frac{mg + P}{P} = \frac{mg}{P} + 1

Take the limit as P→∞P \to \infty: lim⁡P→∞ftotalP=lim⁡P→∞(mgP+1)=0+1=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = \lim_{P \to \infty} \left(\frac{mg}{P} + 1\right) = 0 + 1 = 1

This shows that under an extremely large downward pull, the tool's own weight becomes negligible, and the required upward friction directly scales with and equals the external pulling force PP.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that two opposing pads contact the cylinder and attributes the total friction to only a single pad, underestimating the necessary normal force by a factor of 2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ftotal=μs⋅N  ⟹  μs⋅N=mg+P  ⟹  N=mg+Pμsf_{\text{total}} = \mu_s \cdot N \implies \mu_s \cdot N = mg + P \implies N = \frac{mg + P}{\mu_s}

    Correct

    ftotal=2fs=2μsN=mg+P  ⟹  N=mg+P2μsf_{\text{total}} = 2f_s = 2\mu_s N = mg + P \implies N = \frac{mg + P}{2\mu_s}

    Because the robotic hand clamps the cylinder symmetrically with two identical opposing pads, both pads provide static friction. The maximum total upward friction is 2μsN2\mu_s N rather than μsN\mu_s N.

  2. Step 2

    N=(1.60)(9.80)+00.250=15.680.250=62.7 NN = \frac{(1.60)(9.80) + 0}{0.250} = \frac{15.68}{0.250} = 62.7\text{ N}

    Correct

    N=(1.60)(9.80)2(0.250)=15.680.500=31.4 NN = \frac{(1.60)(9.80)}{2(0.250)} = \frac{15.68}{0.500} = 31.4\text{ N}

    Your numerical substitution and arithmetic are correct based on your derived formula, but your final value is twice the actual requirement due to the missing factor of 22 in the denominator.

  3. Step 3

    ftotal=mg+P  ⟹  lim⁡P→∞mg+PP=1f_{\text{total}} = mg + P \implies \lim_{P \to \infty} \frac{mg + P}{P} = 1

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied vertical equilibrium by equating total upward friction to the total downward load mg+Pmg + P.

You correctly evaluated the asymptotic limit of the ratio as P→∞P \to \infty.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Single-surface friction assumption in multi-contact clamp

You equated the total frictional force to μsN\mu_s N instead of accounting for both pads providing an upward frictional force.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the number of contact surfaces in a symmetrical grip leads to writing ftotal=μsNf_{\text{total}} = \mu_s N instead of summing the frictional forces across all contact interfaces (ftotal=nμsNf_{\text{total}} = n \mu_s N, where n=2n = 2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Count contact interfaces
  • Each contact surface between the tool and a clamping jaw independently exerts a normal force and a corresponding frictional force.

  • Always draw a free-body diagram showing both sides of the gripped object and sum the friction vectors: ftotal=fleft+fright=2μsNf_{\text{total}} = f_{\text{left}} + f_{\text{right}} = 2\mu_s N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the vertical force balance with both contact pads: f1+f2=mg+Pf_1 + f_2 = mg + P.

  2. Use symmetry to write f1=f2=μsNf_1 = f_2 = \mu_s N, so 2μsN=mg+P2\mu_s N = mg + P.

  3. Solve for the minimum normal force: N=mg+P2μsN = \frac{mg + P}{2\mu_s}.

  4. Substitute P=0P = 0: N=(1.60 kg)(9.80 m/s2)2(0.250)=31.4 NN = \frac{(1.60\text{ kg})(9.80\text{ m/s}^2)}{2(0.250)} = 31.4\text{ N}.

Final answer

(a) N=mg+P2μsN = \frac{mg + P}{2\mu_s}; (b) N=31.4 NN = 31.4\text{ N}; (c) lim⁡P→∞ftotalP=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = 1

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a complete free-body diagram labeling each contact point explicitly before writing equilibrium equations.

  • Check whether clamping mechanisms use single or opposing dual jaws when calculating total frictional capacity.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the total friction force f_total with the normal clamping force N when computing the limiting ratio, finding the ratio N / P = 1 / (2 * μ_s) = 2 instead of 1.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    2∗fs=m∗g+P  ⟹  2∗μs∗N=m∗g+P  ⟹  N=m∗g+P2∗μs2 * f_s = m * g + P \implies 2 * \mu_s * N = m * g + P \implies N = \frac{m * g + P}{2 * \mu_s}

  2. Step 2

    N=1.60∗9.802∗0.250  ⟹  N=15.680.500=31.4 NN = \frac{1.60 * 9.80}{2 * 0.250} \implies N = \frac{15.68}{0.500} = 31.4\text{ N}

  3. Step 3

    lim⁡P→∞NP=lim⁡P→∞m∗g+P2∗μs∗P  ⟹  lim⁡P→∞NP=12∗μs=10.500=2\lim_{P \to \infty} \frac{N}{P} = \lim_{P \to \infty} \frac{m * g + P}{2 * \mu_s * P} \implies \lim_{P \to \infty} \frac{N}{P} = \frac{1}{2 * \mu_s} = \frac{1}{0.500} = 2

    Correct

    lim⁡P→∞ftotalP=lim⁡P→∞mg+PP=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = \lim_{P \to \infty} \frac{mg + P}{P} = 1

    The question asks for the limiting ratio of the total upward friction force ftotalf_{\text{total}} to the pulling force PP, not the normal clamping force NN to PP. Because vertical equilibrium requires ftotal=mg+Pf_{\text{total}} = mg + P, the ratio is mg+PP\frac{mg + P}{P}, which approaches 11 as P→∞P \to \infty.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the two identical pads share the load equally.

You properly applied the condition for threshold static friction fs=μsNf_s = \mu_s N to solve for NN.

You accurately carried out the numerical calculation in part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Target variable confusion

You evaluated lim⁡P→∞NP\lim_{P \to \infty} \frac{N}{P} instead of lim⁡P→∞ftotalP\lim_{P \to \infty} \frac{f_{\text{total}}}{P}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the required normal force NN with the total friction force ftotalf_{\text{total}} when setting up the limiting ratio in part (c).

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Friction Force from Normal Force
  • Vertical equilibrium sets the required vertical force (ftotal=mg+Pf_{\text{total}} = mg + P), whereas the normal force NN is horizontal and scales as N=ftotal2μsN = \frac{f_{\text{total}}}{2\mu_s}.

  • Always re-read the target variable in the numerator before taking the limit.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the total required upward friction from vertical equilibrium: ftotal=mg+Pf_{\text{total}} = mg + P.

  2. Set up the requested ratio: ftotalP=mg+PP=mgP+1\frac{f_{\text{total}}}{P} = \frac{mg + P}{P} = \frac{mg}{P} + 1.

  3. Evaluate the limit as P→∞P \to \infty: lim⁡P→∞(mgP+1)=0+1=1\lim_{P \to \infty} \left(\frac{mg}{P} + 1\right) = 0 + 1 = 1.

Final answer

lim⁡P→∞ftotalP=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = 1

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between equilibrium forces (which must directly cancel applied loads) and contact forces like normal forces that enable friction.

  • Practice checking whether an asymptotic question asks about the applied load balance or the clamping mechanism.

OverviewACEpath Teacher's Diagnosis

03 The student omits the gravitational force m * g acting on the cylinder, accounting only for the external force P.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    2⋅μs⋅N=P  ⟹  N=P2μs2 \cdot \mu_s \cdot N = P \implies N = \frac{P}{2\mu_s}

    Correct

    2μsN=mg+P  ⟹  N=mg+P2μs2\mu_s N = mg + P \implies N = \frac{mg + P}{2\mu_s}

    You correctly included the factor of 22 for both gripping pads, but you omitted the downward gravitational force mgmg of the cylinder from your vertical equilibrium condition ∑Fy=0\sum F_y = 0.

  2. Step 2

    N=02⋅0.250  ⟹  N=0 NN = \frac{0}{2 \cdot 0.250} \implies N = 0\text{ N}

    Correct

    N=mg+02μs=(1.60)(9.80)2(0.250)=31.4 NN = \frac{mg + 0}{2\mu_s} = \frac{(1.60)(9.80)}{2(0.250)} = 31.4\text{ N}

    You substituted P=0P = 0 into your formula correctly, but because the weight mgmg was missing from part (a), your result indicated no clamping force is needed to hold the tool against gravity.

  3. Step 3

    ftotal=P  ⟹  lim⁡P→∞PP=1f_{\text{total}} = P \implies \lim_{P \to \infty} \frac{P}{P} = 1

    Correct

    ftotal=mg+P  ⟹  lim⁡P→∞mg+PP=1f_{\text{total}} = mg + P \implies \lim_{P \to \infty} \frac{mg + P}{P} = 1

    You arrived at the correct limit of 11, though your expression for ftotalf_{\text{total}} omitted the weight term mgmg.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly accounted for the two symmetric gripping surfaces by including the factor of 22 in the total friction force.

You correctly related the maximum static friction force to the normal force using fs=μsNf_s = \mu_s N.

You correctly evaluated the limit as P→∞P \to \infty.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Gravitational Force

You set the upward friction equal solely to the external pull PP, leaving out the tool's weight mgmg.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Incomplete free-body diagram: when multiple downward vertical forces act on an object (both gravity and an applied load), all of them must be summed together against the supporting upward frictional forces.

REASONING PATH
Your ACEpath teacher’s suggested approach
Always include weight in vertical equilibrium
  • Every mass mm near Earth's surface experiences a downward gravitational force W=mgW = mg.

  • Draw a free-body diagram and list all downward forces (mg+Pmg + P) before setting up ∑Fy=0\sum F_y = 0.

Perform a physical sanity check at zero applied load
  • When P=0P = 0, an object with mass still requires a non-zero normal force to prevent falling due to gravity.

  • Check your formula at P=0P = 0: if N=0N = 0, the object would drop under its own weight, signaling a missing mgmg term.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the complete vertical equilibrium condition: 2fs−mg−P=0  ⟹  2fs=mg+P2f_s - mg - P = 0 \implies 2f_s = mg + P.

  2. Substitute the slip threshold fs=μsNf_s = \mu_s N: 2μsN=mg+P  ⟹  N=mg+P2μs2\mu_s N = mg + P \implies N = \frac{mg + P}{2\mu_s}.

  3. For P=0P = 0, compute N=mg2μs=(1.60 kg)(9.80 m/s2)2(0.250)=31.4 NN = \frac{mg}{2\mu_s} = \frac{(1.60\text{ kg})(9.80\text{ m/s}^2)}{2(0.250)} = 31.4\text{ N}.

  4. For the limit, evaluate lim⁡P→∞mg+PP=lim⁡P→∞(mgP+1)=0+1=1\lim_{P \to \infty} \frac{mg + P}{P} = \lim_{P \to \infty} \left(\frac{mg}{P} + 1\right) = 0 + 1 = 1.

Final answer

(a) N=mg+P2μsN = \frac{mg + P}{2\mu_s}; (b) N=31.4 NN = 31.4\text{ N}; (c) lim⁡P→∞ftotalP=1\lim_{P \to \infty} \frac{f_{\text{total}}}{P} = 1

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a complete free-body diagram showing both mgmg and PP acting downwards before writing the equilibrium equation.

  • Use limiting cases like P=0P = 0 to verify that your algebraic expression produces physically realistic behavior.

Lock it in

Similar question

01

A vertical wooden plank of mass M=3.0 kgM = 3.0\text{ kg} is clamped between two identical vertical rubber pads. The coefficient of static friction between each pad and the plank is μs=0.30\mu_s = 0.30. Taking g=9.8 m/s2g = 9.8\text{ m/s}^2, calculate the minimum clamping force NN applied by each pad to keep the plank stationary when no external vertical force is applied.

Answer

N=49 NN = 49\text{ N}. Vertical equilibrium requires 2fs=Mg2f_s = Mg, so 2μsN=Mg2\mu_s N = Mg. Thus, N=(3.0)(9.8)2(0.30)=29.40.60=49 NN = \frac{(3.0)(9.8)}{2(0.30)} = \frac{29.4}{0.60} = 49\text{ N}.

02

A robotic gripper with two symmetric parallel jaws holds a metal pipe of mass m=2.5 kgm = 2.5\text{ kg} with a normal force of N=40 NN = 40\text{ N} per pad. The coefficient of static friction is μs=0.40\mu_s = 0.40. Taking g=9.8 m/s2g = 9.8\text{ m/s}^2, find the maximum downward pulling force Pmax⁡P_{\max} that can be applied to the pipe before it starts slipping.

Answer

Pmax⁡=7.5 NP_{\max} = 7.5\text{ N}. The maximum total upward static friction provided by both pads is ftotal=2μsN=2(0.40)(40)=32 Nf_{\text{total}} = 2\mu_s N = 2(0.40)(40) = 32\text{ N}. Vertical equilibrium requires ftotal=mg+Pf_{\text{total}} = mg + P, so Pmax⁡=32−(2.5)(9.8)=32−24.5=7.5 NP_{\max} = 32 - (2.5)(9.8) = 32 - 24.5 = 7.5\text{ N}.

03

A three-jaw cylindrical chuck grips a vertical drill bit of mass m=0.60 kgm = 0.60\text{ kg} symmetrically from three sides, each jaw pressing inward radially with normal force NN. The static friction coefficient is μs=0.20\mu_s = 0.20. An upward axial thrust force of T=18 NT = 18\text{ N} is applied to the bit while drilling. Taking g=9.8 m/s2g = 9.8\text{ m/s}^2, write the equilibrium condition and calculate the minimum normal force NN per jaw required to prevent upward slipping.

Answer

N=20.2 NN = 20.2\text{ N}. Net upward applied force is T−mg=18−(0.60)(9.8)=18−5.88=12.12 NT - mg = 18 - (0.60)(9.8) = 18 - 5.88 = 12.12\text{ N}. All three jaws provide downward static friction to prevent upward slipping: ftotal=3μsN≥12.12 Nf_{\text{total}} = 3\mu_s N \ge 12.12\text{ N}. Thus, N=12.123(0.20)=20.2 NN = \frac{12.12}{3(0.20)} = 20.2\text{ N}.

Loading workspace…