Resources

In a physics laboratory experiment on rotational kinematics, a student uses a digital optical photogate sensor to calibrate a rotating slotted disk attached to a variable-speed motor. The disk perimeter has N=12N = 12 evenly spaced opaque radial spokes. The photogate timer registers the elapsed time between consecutive spoke blockages as Δt=2.85×10−3 s\Delta t = 2.85 \times 10^{-3}\text{ s}. (a) Determine the true rotational period TT of the entire disk. (b) Calculate the rotational frequency of the disk in hertz (Hz\text{Hz}) and in revolutions per minute (rpm\text{rpm}).

Answer and steps

Final answer

(a) T=0.0342 sT = 0.0342\text{ s}; (b) f=29.2 Hz=1.75×103 rpmf = 29.2\text{ Hz} = 1.75 \times 10^3\text{ rpm}

Steps

Part (a): Determine the Rotational Period TT

  1. Relate spoke intervals to one full rotation:
    The disk contains N=12N = 12 evenly spaced spokes around its perimeter. Completing one full revolution (360∘360^\circ) requires the passage of all 1212 intervals between consecutive spokes.
  2. Calculate the period TT:
    The period TT is the total time for one complete revolution: T=N⋅ΔtT = N \cdot \Delta t Substitute the given values: T=12⋅(2.85×10−3 s)=0.0342 sT = 12 \cdot (2.85 \times 10^{-3}\text{ s}) = 0.0342\text{ s}

Common Pitfall: Do not confuse the interval between spokes Δt\Delta t with the full period TT. A single blockage only accounts for a fraction 1N\frac{1}{N} of a complete cycle.


Part (b): Calculate the Rotational Frequency in Hz\text{Hz} and rpm\text{rpm}

  1. Calculate frequency in hertz (Hz\text{Hz}):
    Rotational frequency ff is the reciprocal of the period TT, representing revolutions per second: f=1Tf = \frac{1}{T} f=10.0342 s≈29.2398 Hz≈29.2 Hzf = \frac{1}{0.0342\text{ s}} \approx 29.2398\text{ Hz} \approx 29.2\text{ Hz}
  2. Convert frequency to revolutions per minute (rpm\text{rpm}):
    Since there are 60 seconds60\text{ seconds} in one minute: frpm=f⋅60 s/minf_{\text{rpm}} = f \cdot 60\text{ s/min} frpm=29.2398 s−1⋅60 s/min≈1754.4 rpm≈1.75×103 rpmf_{\text{rpm}} = 29.2398\text{ s}^{-1} \cdot 60\text{ s/min} \approx 1754.4\text{ rpm} \approx 1.75 \times 10^3\text{ rpm}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misidentifies the interval between spokes as the full period of the disk, setting T equal to Δt.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    T=Δt=2.85×10−3 sT = \Delta t = 2.85 \times 10^{-3}\text{ s}

    Correct

    T=N⋅Δt=12⋅(2.85×10−3 s)=0.0342 sT = N \cdot \Delta t = 12 \cdot (2.85 \times 10^{-3}\text{ s}) = 0.0342\text{ s}

    You treated the transit time between two adjacent spokes as the time for an entire revolution. Because there are N=12N = 12 evenly spaced spokes, one full turn requires passing through 12 intervals, so T=N⋅ΔtT = N \cdot \Delta t.

  2. Step 2

    f=1T=12.85×10−3 s≈350.88 Hzf = \frac{1}{T} = \frac{1}{2.85 \times 10^{-3}\text{ s}} \approx 350.88\text{ Hz}

    Correct

    f=1T=10.0342 s≈29.2 Hzf = \frac{1}{T} = \frac{1}{0.0342\text{ s}} \approx 29.2\text{ Hz}

    You correctly used the reciprocal relationship f=1Tf = \frac{1}{T}, but your calculation was affected by the incorrect value of TT from Step 1.

  3. Step 3

    frpm=350.88×60≈21053 rpmf_{\text{rpm}} = 350.88 \times 60 \approx 21053\text{ rpm}

    Correct

    frpm=f⋅60 s/min≈29.24×60≈1.75×103 rpmf_{\text{rpm}} = f \cdot 60\text{ s/min} \approx 29.24 \times 60 \approx 1.75 \times 10^3\text{ rpm}

    You correctly multiplied by 60 to convert from hertz (rev/s) to rpm, but the numerical answer inherits the error from the earlier steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the relationship f=1Tf = \frac{1}{T} to link rotational period to frequency.

You correctly multiplied frequency in hertz by 60 to convert to revolutions per minute.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Period vs. Sub-interval Confusion

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the time elapsed for a fractional rotation (the passage of a single spoke interval) with the total period of one complete revolution (360∘360^\circ).

REASONING PATH
Your ACEpath teacher’s suggested approach
Full Revolution vs. Sector Interval
  • For a rotating body divided into NN equal segments, one complete cycle requires NN consecutive intervals: T=N⋅ΔtT = N \cdot \Delta t.

  • Always count how many repeating intervals constitute one complete 360∘360^\circ rotation before writing down TT.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify that 1 complete revolution equals 12 inter-spoke intervals: T=12⋅Δt=12×(2.85×10−3 s)=0.0342 sT = 12 \cdot \Delta t = 12 \times (2.85 \times 10^{-3}\text{ s}) = 0.0342\text{ s}.

  2. Calculate rotational frequency in hertz: f=1T=10.0342 s≈29.24 Hzf = \frac{1}{T} = \frac{1}{0.0342\text{ s}} \approx 29.24\text{ Hz}.

  3. Convert frequency to rpm: frpm=29.24 rev/s×60 s/min≈1.75×103 rpmf_{\text{rpm}} = 29.24\text{ rev/s} \times 60\text{ s/min} \approx 1.75 \times 10^3\text{ rpm}.

Final answer

(a) T=0.0342 sT = 0.0342\text{ s}; (b) f≈29.2 Hz=1.75×103 rpmf \approx 29.2\text{ Hz} = 1.75 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between the period of a sub-event and the period of an entire cycle.

  • Practice problems involving slotted optical encoders, tachometers, and gear teeth where pulses per revolution must be accounted for.

OverviewACEpath Teacher's Diagnosis

02 The student divides Δt by N instead of multiplying to find the period, incorrectly thinking each spoke represents a fraction of the measured time interval.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    T=ΔtN=2.85×10−3 s12=2.375×10−4 sT = \frac{\Delta t}{N} = \frac{2.85 \times 10^{-3}\text{ s}}{12} = 2.375 \times 10^{-4}\text{ s}

    Correct

    T=N⋅Δt=12⋅(2.85×10−3 s)=0.0342 sT = N \cdot \Delta t = 12 \cdot (2.85 \times 10^{-3}\text{ s}) = 0.0342\text{ s}

    The measured interval Δt\Delta t is only the time between two adjacent spokes, which is 1N\frac{1}{N} of a full turn. One full revolution contains 1212 such intervals, so you must multiply Δt\Delta t by NN, not divide.

  2. Step 2

    f=1T=12.375×10−4 s≈4210.5 Hzf = \frac{1}{T} = \frac{1}{2.375 \times 10^{-4}\text{ s}} \approx 4210.5\text{ Hz}

    Correct

    f=1T=10.0342 s≈29.2 Hzf = \frac{1}{T} = \frac{1}{0.0342\text{ s}} \approx 29.2\text{ Hz}

    Your formula f=1Tf = \frac{1}{T} is completely correct, but the numerical result is affected by the incorrect value of TT from Step 1.

  3. Step 3

    frpm=4210.5×60=252632 rpmf_{\text{rpm}} = 4210.5 \times 60 = 252632\text{ rpm}

    Correct

    frpm=f×60=29.2398×60≈1.75×103 rpmf_{\text{rpm}} = f \times 60 = 29.2398 \times 60 \approx 1.75 \times 10^3\text{ rpm}

    Your unit conversion multiplying frequency in Hz\text{Hz} by 60 s/min60\text{ s/min} is correct, but the numerical answer inherits the error from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the reciprocal relation f=1Tf = \frac{1}{T} to find frequency from period.

You correctly multiplied by 6060 to convert frequency from hertz to revolutions per minute.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted part-whole scaling

Dividing the spoke interval by the number of spokes instead of multiplying to find the full rotational period.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the time between two consecutive spokes as the time for an entire rotation and tried to find the time per spoke, rather than recognizing that Δt\Delta t is already the time for a single 112\frac{1}{12} sector of a revolution.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity-check sub-interval vs. full period
  • A complete period TT must be strictly greater than the time Δt\Delta t between consecutive subdivisions of a cycle.

  • Before calculating, ask yourself: 'Does one full rotation take more time or less time than moving between two adjacent spokes?'

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply the time interval between consecutive spokes by the total number of spokes: T=12×(2.85×10−3 s)=0.0342 sT = 12 \times (2.85 \times 10^{-3}\text{ s}) = 0.0342\text{ s}.

  2. Take the reciprocal to find the frequency in hertz: f=10.0342 s≈29.2 Hzf = \frac{1}{0.0342\text{ s}} \approx 29.2\text{ Hz}.

  3. Convert the frequency to revolutions per minute: frpm=29.2398×60≈1.75×103 rpmf_{\text{rpm}} = 29.2398 \times 60 \approx 1.75 \times 10^3\text{ rpm}.

Final answer

(a) T=0.0342 sT = 0.0342\text{ s}; (b) f=29.2 Hz=1.75×103 rpmf = 29.2\text{ Hz} = 1.75 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the physical meaning of given time intervals (e.g., 'time for 11 sector' vs. 'time for 11 full cycle').

  • Check that calculated periods are larger than sub-interval measurements before proceeding to downstream calculations.

OverviewACEpath Teacher's Diagnosis

03 The student calculates frequency correctly in Hz but divides by 60 instead of multiplying by 60 when converting to rpm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    T=12⋅2.85×10−3 s=0.0342 sT = 12 \cdot 2.85 \times 10^{-3}\text{ s} = 0.0342\text{ s}

  2. Step 2

    f=10.0342 s≈29.24 Hzf = \frac{1}{0.0342\text{ s}} \approx 29.24\text{ Hz}

  3. Step 3

    frpm=29.2460≈0.487 rpmf_{\text{rpm}} = \frac{29.24}{60} \approx 0.487\text{ rpm}

    Correct

    frpm=f⋅60 s/min=29.24 s−1⋅60 s/min≈1.75×103 rpmf_{\text{rpm}} = f \cdot 60\text{ s/min} = 29.24\text{ s}^{-1} \cdot 60\text{ s/min} \approx 1.75 \times 10^3\text{ rpm}

    Because 1 Hz=1 rev/s1\text{ Hz} = 1\text{ rev/s} and there are 60 seconds60\text{ seconds} in a minute, a wheel completes 6060 times as many revolutions in one full minute as it does in one second. You divided by 6060 instead of multiplying.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that a complete rotation requires 1212 consecutive spoke intervals and calculated the rotational period T=0.0342 sT = 0.0342\text{ s}.

You correctly applied f=1Tf = \frac{1}{T} to find the rotational frequency in hertz.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion error (inverted rate factor)

You divided by 6060 instead of multiplying by 6060 when converting revolutions per second to revolutions per minute.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating the unit conversion from seconds to minutes as division by 6060 without setting up dimensional analysis. Because time is in the denominator of a frequency unit (rev/s\text{rev}/\text{s}), replacing s\text{s} with 160 min\frac{1}{60}\text{ min} moves the factor of 6060 to the numerator.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis for Rates
  • rev/s⋅60 s1 min=60 rev/min\text{rev}/\text{s} \cdot \frac{60\text{ s}}{1\text{ min}} = 60\text{ rev}/\text{min}

  • Always write out explicit conversion fractions so the second units cancel algebraically: (revs)×(60 s1 min)\left(\frac{\text{rev}}{\text{s}}\right) \times \left(\frac{60\text{ s}}{1\text{ min}}\right).

Sanity Check on Time Scale
  • A longer observation time means more completed cycles.

  • Ask yourself whether the object should complete more or fewer rotations in a full minute compared to a single second.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert revolutions per second (Hz\text{Hz}) to revolutions per minute by multiplying by 60 s/min60\text{ s/min}:

  2. frpm=29.24 rev/s⋅60 s/min=1754.4 rpmf_{\text{rpm}} = 29.24\text{ rev/s} \cdot 60\text{ s/min} = 1754.4\text{ rpm}

  3. Round to three significant figures consistent with the given data: 1.75×103 rpm1.75 \times 10^3\text{ rpm}.

Final answer

(a) T=0.0342 sT = 0.0342\text{ s}; (b) f=29.2 Hz=1.75×103 rpmf = 29.2\text{ Hz} = 1.75 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting rates with inverted time units (e.g., m/s\text{m/s} to m/min\text{m/min} or Hz\text{Hz} to rpm\text{rpm}) using unit-cancellation fractions.

  • Perform a physical intuition check whenever converting from per-second to per-minute quantities.

Lock it in

Similar question

01

A cooling fan has 5 identical blades. An optical tachometer measures the time between consecutive blade passes as Δt=4.0×10−3 s\Delta t = 4.0 \times 10^{-3}\text{ s}. Find the rotational period TT of the fan and its rotational speed in rpm\text{rpm}.

Answer

T=5⋅(4.0×10−3 s)=0.020 sT = 5 \cdot (4.0 \times 10^{-3}\text{ s}) = 0.020\text{ s}. The rotational frequency is f=1T=50 Hzf = \frac{1}{T} = 50\text{ Hz}. Converting to rpm gives frpm=50×60=3000 rpmf_{\text{rpm}} = 50 \times 60 = 3000\text{ rpm}.

02

An optical encoder disk with 60 radial slots is mounted on a motor shaft. A photodiode detects pulses at a frequency of 2400 Hz2400\text{ Hz}. (a) What is the time interval Δt\Delta t between consecutive pulses? (b) What is the period TT and rotational frequency ff of the motor shaft?

Answer

(a) Δt=1fpulse=12400 s−1≈4.17×10−4 s\Delta t = \frac{1}{f_{\text{pulse}}} = \frac{1}{2400\text{ s}^{-1}} \approx 4.17 \times 10^{-4}\text{ s}. (b) The rotational frequency of the shaft is f=fpulse60=240060=40 Hzf = \frac{f_{\text{pulse}}}{60} = \frac{2400}{60} = 40\text{ Hz}, which gives a rotational period of T=140 Hz=0.025 sT = \frac{1}{40\text{ Hz}} = 0.025\text{ s} (or T=60⋅Δt=0.025 sT = 60 \cdot \Delta t = 0.025\text{ s}).

03

A bicycle wheel of diameter D=0.70 mD = 0.70\text{ m} has 36 evenly spaced spokes. A magnetic sensor fixed to the frame measures the time between consecutive spoke passages as Δt=3.5 ms\Delta t = 3.5\text{ ms}. Calculate (a) the rotational period TT of the wheel, and (b) the linear forward speed vv of the bicycle in m/s\text{m/s}, assuming rolling without slipping.

Answer

(a) The wheel period is T=36⋅(3.5×10−3 s)=0.126 sT = 36 \cdot (3.5 \times 10^{-3}\text{ s}) = 0.126\text{ s}. (b) The wheel's angular speed is ω=2πT=2π0.126 s≈49.87 rad/s\omega = \frac{2\pi}{T} = \frac{2\pi}{0.126\text{ s}} \approx 49.87\text{ rad/s}. With radius R=0.35 mR = 0.35\text{ m}, the linear speed is v=ωR=49.87×0.35≈17.5 m/sv = \omega R = 49.87 \times 0.35 \approx 17.5\text{ m/s} (or v=πDT=π×0.700.126≈17.5 m/sv = \frac{\pi D}{T} = \frac{\pi \times 0.70}{0.126} \approx 17.5\text{ m/s}).

Loading workspace…