Resources
A package of mass is launched horizontally from rest by compressing a horizontal spring against a rigid wall. The spring has a spring constant of and is initially compressed by . Upon release at the equilibrium position of the spring (), the package leaves the spring and slides along a rough horizontal runway with a coefficient of kinetic friction for a distance of . It then travels smoothly onto a frictionless ramp inclined at above the horizontal. Taking , calculate: (a) the constant kinetic frictional force acting on the package along the runway, (b) the thermal energy generated by friction along the runway, and (c) the maximum vertical height attained by the package on the incline.
Answer and steps
Final answer
(a) ; (b) ; (c) .
Steps
Part (a): Kinetic Frictional Force
-
Identify the vertical forces on the horizontal runway: Along the flat, horizontal surface, the package does not accelerate vertically. Setting the net vertical force to zero: where:
- Calculate the kinetic frictional force (): Using the definition of kinetic friction: Substitute the given values:
Part (b): Thermal Energy Generated by Friction
- Relate friction to thermal energy: The thermal energy produced by friction is equal to the magnitude of the work done against friction over the distance :
- Compute :
Part (c): Maximum Vertical Height Attained
- Apply the Work-Energy Theorem: The total initial energy of the system is the elastic potential energy stored in the compressed spring: Substitute and :
- Find the mechanical energy remaining after the rough section: As the package slides across the rough runway, thermal energy is dissipated:
- Determine the maximum vertical height (): The package then slides up the frictionless ramp until it momentarily comes to rest at maximum height . All remaining kinetic energy transforms into gravitational potential energy:
(Note: The angle of the incline determines the distance traveled along the slope, but the vertical height depends strictly on gravitational potential energy and is independent of the incline angle.)
Typical errors
01 The student forgets to account for energy dissipated by friction when finding the maximum height, equating initial spring potential energy directly to gravitational potential energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You set the initial spring potential energy equal to the final gravitational potential energy without accounting for the of mechanical energy dissipated as heat across the rough runway.
- Step 4Correct
Your final height value is inflated because it was derived from the energy equation that omitted friction losses.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the normal force and kinetic friction for part (a).
You correctly calculated the thermal energy generated across the runway for part (b).
You correctly evaluated the initial elastic potential energy stored in the spring.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the entire journey as an isolated conservative system by using , forgetting that friction is a non-conservative force that removes mechanical energy ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Conservation with Non-Conservative Work
Whenever a system slides across a rough surface, always subtract the thermal energy dissipated by friction before equating remaining mechanical energy to the final potential or kinetic energy.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b) ; (c)
02 The student calculates the distance traveled along the incline instead of the vertical height by dividing the vertical height by sin(25.0°).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
The question specifically asked for the maximum vertical height . The value is already that vertical height; dividing by computes the distance traveled along the incline (), not the vertical height.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the normal force and kinetic friction force.
You accurately calculated the thermal energy generated by friction along the horizontal track.
You correctly formulated the conservation of energy equation relating initial spring potential energy, dissipated thermal energy, and final gravitational potential energy.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the geometric distance traveled along the incline surface () with the vertical elevation gain (), leading you to apply an unnecessary trigonometric conversion to a value that was already the vertical height.
REASONING PATH
Your ACEpath teacher’s suggested approach- Gravitational Potential Energy and Height
Gravitational potential energy near Earth's surface depends strictly on vertical height: , where is measured perpendicular to the horizontal ground.
Check whether the problem asks for vertical height or distance along the slope before applying trigonometric ratios.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecognize that the symbol in gravitational potential energy directly represents the vertical height above the reference level.
Since the question asks for the maximum vertical height attained on the incline, no conversion using is needed.
State the final vertical height directly: .
(a) ; (b) ; (c)
03 The student incorrectly includes the normal force component on the incline when calculating the normal force on the horizontal runway.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The friction occurs entirely along the horizontal runway, not on the incline. On a flat horizontal surface with no vertical applied forces, the normal force balances gravity directly ().
- Step 2Correct
You correctly applied , but this value is affected by your incorrect normal force from Step 1.
- Step 3Correct
You correctly related thermal energy to the work done against friction, but the numerical value inherits the error from Step 2.
- Step 4Correct
Your work-energy theorem setup is conceptually sound, but the final height is affected by the underestimated thermal energy loss.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the friction equation .
You correctly recognized that the thermal energy dissipated equals the work done against friction ().
You correctly formulated the conservation of energy equation relating initial spring elastic energy to thermal energy and final gravitational potential energy.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou applied the inclined-plane normal force formula to a segment that is flat and horizontal. Friction acts solely on the horizontal track, whereas the ramp is frictionless.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match normal force to track geometry
On a horizontal track with no vertical angled pulls, . The factor belongs only to an incline of angle .
Always draw a separate free-body diagram for each distinct track section to verify surface orientation before computing friction.
- Identify where friction actually acts
Only evaluate friction on sections specified as rough.
Check the problem description: the horizontal runway has friction (), while the inclined ramp is explicitly frictionless.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the normal force on the horizontal runway: .
Calculate kinetic friction: .
Compute thermal energy: .
Apply energy conservation: .
Solve for maximum height: .
(a) ; (b) ; (c)
Lock it in
How does friction modify the mechanical energy conservation equation ?
Mechanical energy is not conserved: , where is the thermal energy generated by friction.
Similar question
A block is launched along a horizontal surface with an initial kinetic energy of . It slides across a rough patch with a constant kinetic friction force of , then moves up a frictionless incline. Calculate the maximum vertical height the block reaches on the incline ().
Answer
. Thermal energy dissipated: . Remaining mechanical energy: . At peak height, .
A toy car of mass is compressed against a spring () by on a frictionless horizontal floor. It is released, travels across a rough section of length with , and then ascends a frictionless incline. Find: (a) the thermal energy generated on the rough patch, and (b) the maximum height reached on the incline ().
Answer
(a) ; (b) . Initial elastic potential energy: . Normal force: . Friction: . Thermal energy: . Remaining energy at base of incline: . Setting gives .
A package of mass slides down a frictionless curved ramp from a height of , then slides across a flat rough surface of length with , and finally compresses a horizontal spring with spring constant . Taking , determine the maximum compression of the spring.
Answer
. Initial gravitational potential energy: . Thermal energy lost on the rough surface: . Remaining mechanical energy: . This energy converts into spring elastic potential energy: (or with rounded intermediate values).