Resources
A horizontal uniform beam of length and mass is hinged to a vertical wall at point (the fulcrum). A vertical downward load of hangs from the right end of the beam. To support the load, a high-strength tie-cable is attached to the beam at a distance of from the hinge, making an angle of above the horizontal beam. Taking and setting up the torque equilibrium equation about with counterclockwise torques defined as positive: (a) calculate the required tensile force in the cable, and (b) determine the horizontal and vertical reaction force components, and , exerted by the hinge on the beam.
Answer and steps
Final answer
(a) ; (b) , (acting downward)
Steps
Identify Forces and Torque Arms
A body in static equilibrium satisfies both rotational equilibrium () and translational equilibrium ().
The forces acting on the uniform horizontal beam of length are:
- Weight of the beam (): Because the beam is uniform, its weight acts downward at its center of mass, which is at the midpoint:
- Hanging load (): Acts downward at the right end of the beam:
- Cable tension (): Acts at distance from the hinge, oriented upward and toward the wall at an angle above the horizontal. Its components are:
- Hinge reaction force (): Acts at the fulcrum with horizontal component (assumed rightward) and vertical component (assumed upward).
Calculate the Cable Tension
Choose the hinge as the rotation axis. The reaction forces and , as well as , pass directly through and produce zero torque.
Taking counterclockwise (CCW) torques as positive:
- Upward cable component creates a positive (CCW) torque:
- Beam weight creates a negative (CW) torque:
- End load creates a negative (CW) torque:
Setting the sum of torques about to zero:
Substitute the numerical values:
Determine the Hinge Reaction Components and
Apply translational equilibrium conditions in the horizontal and vertical directions.
Horizontal Equilibrium ():
Using :
Because , the horizontal reaction force acts to the right (pushing away from the wall to counter the leftward pull of the cable).
Vertical Equilibrium ():
Calculate the upward lift provided by the cable:
Substitute back to find :
Common Pitfall: A negative vertical reaction force () indicates that the assumed upward direction was opposite to reality. Here, the vertical component of the cable tension () exceeds the total downward gravitational load (). Consequently, the hinge must pull downward with a magnitude of to prevent the beam from rotating upward.
Typical errors
01 The student misplaces the beam's weight at the full length of the beam instead of at its center of mass, leading to an overestimated cable tension and incorrect vertical reaction force.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the beam is uniform, its weight acts at the geometric center (), not at the outer end (). Using doubles the torque contribution of the beam's weight.
- Step 3Correct
Your horizontal equilibrium equation is completely correct, but your numerical result is affected by the overestimated value of .
- Step 4Correct
Your vertical force balance equation is set up correctly, but the resulting value is affected by your earlier cable tension value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the cable tension into perpendicular and parallel components.
You chose the hinge as the pivot point to eliminate the unknown reaction forces from the torque equation.
You correctly formulated translational equilibrium in both the horizontal and vertical directions.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote the full beam length as the moment arm for the beam's weight instead of half the length.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the location of an end load with the center of gravity of a uniform rigid body. A uniform member's weight must be modeled as a single equivalent point force acting strictly at its midpoint.
REASONING PATH
Your ACEpath teacher’s suggested approach- Center of Mass of Uniform Bodies
For any uniform symmetric object, the total gravitational force acts at its geometric centroid: .
Draw the weight vector directly at the midpoint of the beam on your free-body diagram before writing the torque equation.
- Lever Arm Verification
The lever arm is the perpendicular distance from the pivot to the line of action of the force.
Double-check each term in by tracing from the pivot to the specific point of application of that individual force.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b) , (acting downward)
02 The student uses the full tension force T rather than its perpendicular component T * sin(35.0°) when calculating torque, resulting in an underestimated tension and incorrect hinge forces.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the angle factor in the cable's torque term. Because the cable pulls at relative to the horizontal beam, only its perpendicular component produces a lever torque about the hinge .
- Step 3Correct
Your algebraic setup for horizontal force balance is completely sound, but substituting the underestimated tension caused this value to be too low.
- Step 4Correct
Your force balance expression for is conceptually correct, but because the true tension produces an upward lift of that exceeds the total downward load of , the actual hinge reaction force points downward ().
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately located the beam's center of mass at its midpoint and determined its weight.
You correctly identified the lever arms for both downward gravitational forces.
You correctly formulated the horizontal and vertical translational equilibrium equations.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the tie-cable as if it were oriented perpendicular to the beam when computing torque, even though you correctly decomposed it into components later for force balance.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the total magnitude of an angled force with its perpendicular torque-producing component .
REASONING PATH
Your ACEpath teacher’s suggested approach- Torque from an Angled Force
, where is the angle between the position vector along the beam and the force vector .
Whenever a force is not perpendicular to the lever arm, either multiply by or explicitly use the perpendicular force component before setting up .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the torque equation about fulcrum : .
Substitute numerical values: .
Solve for tension: .
Compute horizontal hinge reaction: .
Compute vertical hinge reaction: (acting downward).
(a) ; (b) , (downward)
03 The student confuses the trigonometric components by using cos(35.0°) instead of sin(35.0°) for the perpendicular force component in torque, causing erroneous cable tension and reaction forces.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
For a horizontal beam, the component of tension perpendicular to the lever arm is the vertical component . Using takes the component parallel to the beam, which produces zero torque about the hinge.
- Step 3Correct
Your horizontal equilibrium equation is algebraically correct, but the numerical value is affected by your earlier tension value.
- Step 4Correct
Your vertical force balance equation is set up correctly, but substituting the incorrect tension yields a positive vertical hinge force instead of the true downward force of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the weight of the uniform beam and placed it at the midpoint.
You correctly established the equilibrium equations for both horizontal and vertical translation.
You correctly identified the signs of clockwise and counterclockwise torques about the fulcrum.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou swapped the sine and cosine components when resolving the cable tension for torque.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the perpendicular and parallel components of an angled force acting on a horizontal lever arm. Torque is caused only by the perpendicular component , while the parallel component passes through the rotation axis and exerts zero torque.
REASONING PATH
Your ACEpath teacher’s suggested approach- Perpendicular Component for Torque
For a force applied at distance along a line making angle with the lever arm, the torque magnitude is .
Draw the force components directly onto the diagram. Verify whether the component causing rotation is opposite (sine) or adjacent (cosine) to the given angle.
- Hinge Reaction Direction Check
If the upward vertical component of tension exceeds total downward weight, the hinge must pull downward () to keep static balance.
Compare with : if , expect a negative value indicating a downward reaction.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the torque balance about the hinge using the perpendicular component of tension: .
Solve for tension: .
Substitute into the horizontal balance: .
Substitute into the vertical balance: (acting downward).
(a) ; (b) , (downward)
Lock it in
Where does the gravitational force (weight) act on a uniform beam of length ?
At its center of mass, which is at the geometric midpoint: from either end.
Similar question
A uniform horizontal shelf of length and weight is hinged at the left wall and supported by a vertical cord at the right end. Calculate the tension in the cord.
Answer
. Taking torques about the hinge: .
A uniform beam of length and mass is hinged at point . An additional load of hangs at from . A cable attached at the right end () pulls upward at an angle of above the horizontal. Taking , find the cable tension for static equilibrium.
Answer
. Weight acts at . Torque about : .
A uniform horizontal crane boom of length and weight holds a crate at its tip. A tie rod attaches at from the hinge at an angle of above the boom. Determine: (a) the tension in the tie rod, and (b) the vertical reaction force at the hinge.
Answer
(a) ; (b) (acting downward). Steps: (a) . (b) .