Resources
In an introductory physics laboratory, a student determines the density of a solid cylindrical brass weight. The mass is measured using an electronic balance as . The diameter and height of the cylinder are measured with a vernier caliper as and , respectively. Assuming the cylinder volume is and all measurement uncertainties are independent and random, calculate the experimental density in and its propagated absolute uncertainty using the standard error propagation formula in quadrature. Express the final result in the standard form with appropriate significant figures.
Answer and steps
Final answer
Steps
Calculate the Volume and Central Value of Density
The formula for the volume of a cylinder with diameter and height is:
Substitute the given values and :
The experimental density is the ratio of mass to volume :
Substitute :
Determine Relative Uncertainties
Calculate the fractional (relative) uncertainties for each independent measurement:
- Mass:
- Diameter:
- Height:
Propagate Uncertainties in Quadrature
Since , the exponent of each variable acts as a multiplier on its relative uncertainty before adding in quadrature:
Common Pitfall: Forgetting the factor of multiplying . Because the diameter is squared in the denominator, its fractional uncertainty contributes twice as heavily to the total uncertainty.
Substitute the relative uncertainties:
Calculate Absolute Uncertainty and State the Result
Multiply the relative uncertainty by the nominal density:
Following standard reporting conventions, the uncertainty is expressed to two significant figures, and the central value is matched to the same decimal place (the thousandths place):
Typical errors
01 The student forgets to multiply the fractional uncertainty of diameter by its exponent of 2 when propagating uncertainty in quadrature.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because density depends on diameter squared (), the power rule of uncertainty propagation requires you to multiply the fractional uncertainty of diameter by before squaring in quadrature.
- Step 3Correct
Your conversion from relative to absolute uncertainty followed the right steps, but the numerical result was affected by the omitted factor of in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the volume of the cylinder and the central value of the density.
You correctly computed the individual fractional uncertainties , , and .
You correctly multiplied the relative uncertainty by the central density value to obtain an absolute uncertainty.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the diameter as if it entered the density formula with an exponent of rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisWhen combining independent variables related by products and powers (), the fractional uncertainty of each variable must be scaled by its absolute exponent before adding in quadrature: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Exponents in Power-Law Quantities
For any relation , the fractional uncertainty is .
Write out the functional dependence of on the raw measured quantities: , identifying exponents , , and .
- Scale Relative Uncertainties Before Squaring
Multiply each relative uncertainty by the magnitude of its exponent before summing squares under the radical.
Replace with .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the corrected relative uncertainty: .
Calculate the absolute uncertainty: .
Match the central value's precision to the uncertainty (thousandths place): .
02 The student adds absolute uncertainties directly instead of combining relative uncertainties in quadrature for multiplication and division.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You added the absolute measurement uncertainties directly. Because density is given by , which involves products, quotients, and powers, you must combine the relative (fractional) uncertainties in quadrature, weighting by its exponent of .
- Step 3Correct
Your final value and reported precision were affected by the incorrectly calculated absolute uncertainty.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the cylindrical volume from the measured diameter and height.
You correctly determined the central value of the density by dividing mass by volume.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated uncertainty propagation as a direct sum of absolute errors rather than combining relative uncertainties in quadrature for a quotient involving powers.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating addition/subtraction error rules with multiplication/division/power error propagation rules, as well as attempting to add quantities with incompatible units (grams and centimeters).
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Units Before Adding Uncertainties
Absolute uncertainties can only be added if the quantities themselves are added or subtracted and have the same physical units.
Check whether () and () have the same units as (). Since they do not, they cannot be directly summed.
- Power and Multiplicative Propagation Rule
For , relative uncertainties combine in quadrature: .
Calculate fractional uncertainties , , and , multiply by , square and sum them, take the square root, and then multiply by to get .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the fractional uncertainties: , , and .
Combine fractional uncertainties in quadrature: .
Find absolute uncertainty: .
03 The student adds relative uncertainties linearly instead of combining them in quadrature.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You added the fractional uncertainties linearly. For independent and random measurement errors, standard propagation requires summing the terms in quadrature (taking the square root of the sum of the squares of each component).
- Step 3Correct
Your arithmetic was applied consistently to your previous fractional uncertainty, but the value is elevated because it followed the linear sum instead of quadrature.
- Step 4Correct
Because the propagated uncertainty was overestimated, the stated uncertainty and resulting rounding for the nominal density reflect the earlier quadrature error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the volume and central density from the measured dimensions.
You recognized that the relative uncertainty in diameter carries an exponent multiplier of .
You correctly converted the relative uncertainty back into an absolute uncertainty by multiplying by the central value.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou applied the formula for worst-case (maximum possible) bound error rather than standard error propagation in quadrature, which applies to uncorrelated, independent random errors.
REASONING PATH
Your ACEpath teacher’s suggested approach- Quadrature vs. Linear Addition
For independent random variables , relative uncertainties combine via .
Always square each weighted relative uncertainty, add them together, and take the square root unless specifically instructed to find the worst-case bound.
CORRECTED PATH
ACEpath Teacher's DemonstrationEvaluate individual terms: , , and .
Sum in quadrature: .
Find absolute uncertainty: .
Lock it in
If and has relative uncertainty , what is the relative uncertainty ?
. The relative uncertainty scales directly by the magnitude of the exponent.
Similar question
The kinetic energy of an object is given by . The mass is measured with a relative uncertainty of , and the speed is measured with a relative uncertainty of . Calculate the fractional uncertainty .
Answer
Using quadrature with the power rule: .
The acceleration due to gravity is determined using a simple pendulum via . A student measures and period . Calculate the central value of and its absolute uncertainty .
Answer
Central value: . Fractional uncertainties: ; . Total relative uncertainty: . Absolute uncertainty: . Result: .
A cylindrical wire has resistance , where is resistivity, is length, and is diameter. If the relative uncertainties are , , and , find the percentage uncertainty in . Which measurement contributes the most to the total uncertainty?
Answer
Propagate in quadrature: . The diameter measurement contributes the most because its relative uncertainty is doubled by the exponent of , yielding , which is over of the total variance.