Resources
A rectangular block of mass is pressed against a vertical wall by an externally applied force directed at an angle of above the horizontal. The coefficients of friction between the block and the vertical wall are and . Adopting a standard Cartesian coordinate system where the positive -axis points perpendicular into the wall and the positive -axis points vertically upward, calculate the minimum force magnitude required to prevent the block from slipping downward under gravity. Use .
Answer and steps
Final answer
Steps
Identify the Forces and Resolve Components
To find the minimum magnitude of the applied force required to keep the block stationary, we analyze the forces acting on the block in static equilibrium at the verge of slipping downward.
The applied force acts at an angle above the horizontal, directed into the wall. We resolve into horizontal and vertical components:
- Horizontal component into the wall:
- Vertical component pointing upward:
The other forces acting on the block are:
- The downward gravitational force:
- The normal force exerted outward by the vertical wall:
- The static friction force exerted upward by the wall:
Apply Equilibrium in the Horizontal Direction
Because the block does not move horizontally, the net horizontal force must be zero:
Determine the Maximum Static Friction Force
Because we are finding the minimum force to prevent slipping downward, the impending motion of the block is downward. Consequently, the force of static friction opposes this tendency and acts vertically upward.
At the threshold of slipping, static friction reaches its maximum possible value, characterized by the coefficient of static friction (rather than the kinetic coefficient , since the block remains at rest):
Apply Equilibrium in the Vertical Direction
For the block to remain in equilibrium:
Substitute the expressions for and :
Factor out :
Solve for :
Substitute the Numerical Values
Using , , , and :
Typical errors
01 The student uses the kinetic friction coefficient instead of the static friction coefficient when solving for the impending slipping condition.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the block is stationary and on the verge of slipping, you need the maximum static friction force governed by , not kinetic friction .
- Step 3Correct
Your algebraic setup and simplification for vertical equilibrium were carried out properly, but this step inherits the incorrect friction coefficient from earlier.
- Step 4Correct
Your arithmetic was accurate based on your setup, but using led to an overestimated force requirement.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the applied force into perpendicular and parallel components relative to the wall.
You properly recognized that upward friction and the vertical component of the applied force work together to balance gravity.
You demonstrated clear, accurate algebraic manipulations and substitution steps throughout your work.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the condition of impending slippage (static equilibrium threshold using ) with active sliding motion (which uses ).
REASONING PATH
Your ACEpath teacher’s suggested approach- State of Motion vs. Threshold
Static friction applies whenever surfaces do not slide relative to each other, with maximum static friction given by . Kinetic friction applies only after sliding has begun ().
Ask yourself: Is the object sliding, or are we preventing it from starting to slide? If preventing motion, select .
CORRECTED PATH
ACEpath Teacher's Demonstration02 The student forgets that the applied force has a vertical component supporting the block against gravity, equating upward friction alone to gravity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the applied force acts at an angle above the horizontal, it has an upward vertical component that helps support the block. Vertical equilibrium requires , so friction alone does not need to support the full gravitational force.
- Step 3Correct
Your numerical substitutions and arithmetic follow logically from your previous vertical equation, but the missing vertical force component carried forward into this calculation.
- Step 4Correct
Your final magnitude is incorrect due to the omitted upward component of the applied force in the vertical equilibrium equation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the applied force into the horizontal axis to relate normal force to applied force.
You correctly recognized that static friction reaches its maximum threshold to prevent impending downward slip.
You executed the arithmetic and algebraic isolation accurately based on your equation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated static friction as the only upward force resisting gravity, overlooking the fact that an angled force directed upward into a wall also contributes an upward vertical component to support the block.
REASONING PATH
Your ACEpath teacher’s suggested approach- Resolve All Angled Forces First
Every force vector acting at an angle must be decomposed into orthogonal components ( and ) before writing equilibrium equations.
Draw a free-body diagram and explicitly write down both components of before setting up .
- Account for All Vertical Forces
In static equilibrium, , meaning the sum of all upward forces must balance the sum of all downward forces: .
Check whether any external applied force pushes partially upward before equating friction directly to weight.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up vertical equilibrium at the verge of slipping downward: .
Substitute : .
Substitute values: .
Calculate: .
03 The student assumes the normal force is equal to the full applied force Fapp rather than its horizontal component Fapp cos θ.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the applied force is directed at an angle above the horizontal, only its horizontal component presses the block against the wall. Applying gives rather than .
- Step 2
- Step 3Correct
Your algebraic solving and arithmetic steps were executed logically, but the expression was affected by substituting instead of .
- Step 4Correct
This final value follows directly from the earlier normal force error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that impending downward slip engages maximum static friction directed vertically upward.
You accurately resolved the upward vertical component of the applied force as .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed the normal force from a vertical surface equals the total magnitude of the applied force, forgetting to resolve the applied force perpendicular to the contact surface.
REASONING PATH
Your ACEpath teacher’s suggested approach- Resolve Forces Perpendicular to the Surface
The normal force balances all forces acting perpendicular to the contact interface.
Always write along the axis perpendicular to the contact surface before computing .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute into the vertical equilibrium equation: .
Evaluate the trigonometric terms: .
Solve for the force magnitude: .
Lock it in
When a problem asks for the minimum force to 'prevent an object from slipping', which friction coefficient should you use?
Use the coefficient of static friction , because the object remains at rest at the impending slip threshold ().
Similar question
A block of mass is held against a vertical wall by a horizontal force . If and , calculate the minimum magnitude of required to prevent the block from slipping downward. Use .
Answer
. Vertical equilibrium requires . Since and , we have .
A crate rests on a horizontal floor where and . You pull on the crate with a rope angled at above the horizontal. What minimum tension is needed to start the crate moving? Use .
Answer
. Impending slip occurs when . Rearranging yields .
A block of mass is pressed against a vertical wall with and by an applied force angled at above the horizontal. Find the maximum force magnitude that can be applied before the block starts slipping upward. Use .
Answer
. When slipping upward impends, friction acts downward: . Vertical balance gives . Thus .