Resources
In an introductory physics lab, a dynamic cart fitted with an ultrasonic sonic ranger travels along a horizontal low-friction track. The ultrasonic ranger samples position data at regular intervals, generating the following ordered pairs : , , , , and . (a) Using the symmetric central difference approximation for slope on a position-time graph, , compute the instantaneous velocity at and . (b) Assuming the position follows a constant acceleration model , determine the numerical value of the constant acceleration from the curvature of the data.
Answer and steps
Final answer
(a) and ; (b)
Steps
Part (a): Calculating Instantaneous Velocity Using Central Differences
The central difference approximation estimates the instantaneous rate of change (the tangent slope) at a point by evaluating the secant slope between the neighboring points symmetrically spaced by :
-
Velocity at : The neighboring time points are and . From the given data:
Substitute these values into the formula:
-
Velocity at : The neighboring time points are and . From the given data:
Substitute these values into the formula:
Common Pitfall: A frequent mistake is dividing by rather than . Because the interval spans from to , the total time elapsed is .
Part (b): Determining Constant Acceleration
For an object undergoing uniformly accelerated motion, the acceleration is the constant rate of change of velocity:
Using the two calculated instantaneous velocities separated by :
Alternative Verification Using Second Finite Differences:
In a quadratic position model , the second central difference relates directly to acceleration by:
Evaluating at :
Solving for :
Typical errors
01 The student forgets the factor of 2 in the denominator of the central difference approximation, dividing by Δt instead of 2Δt.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the correct neighboring position coordinates and , but the time interval spanning from to is , not .
- Step 2Correct
Similarly, the span from to covers two sampling intervals, so the denominator must be .
- Step 3Correct
Your acceleration formula and algebraic substitution were completely sound, but your result was doubled due to the incorrect velocities carried forward from Part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the symmetric neighboring data points and for both central difference evaluations.
You set up the finite difference formula for constant acceleration with the correct elapsed time of .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by rather than the full symmetric time baseline .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the single-step sampling interval with the two-step time span between and in symmetric finite difference approximations.
REASONING PATH
Your ACEpath teacher’s suggested approach- Time Baseline in Symmetric Differences
In the central difference formula , the total elapsed time between the two evaluation points is .
Always verify that your denominator equals the actual difference between the two times used in the numerator: .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate with the full interval: .
Recalculate with the full interval: .
Re-evaluate the constant acceleration using the corrected velocities: .
(a) , ; (b)
02 The student equates the coefficient of t² directly to acceleration without accounting for the factor of 1/2 in the kinematic formula.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
In the standard kinematic model , the coefficient of is , not . You need to multiply the coefficient by to obtain the true acceleration.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied the symmetric central difference quotient using the full time span .
You accurately determined the quadratic polynomial coefficients describing the position-time data.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou read off the coefficient of as the acceleration instead of equating it to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the quadratic term's coefficient in with the acceleration itself, forgetting that integrating acceleration twice introduces a factor of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Match quadratic coefficient with kinematic definition
In , , so .
Always multiply the coefficient by (or take the second derivative) when extracting acceleration from a position function.
- Cross-check with velocity difference
for constant acceleration.
Verify your result using the velocities from part (a): .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare the polynomial directly to the kinematic model .
Equate the coefficients of the term: .
Multiply both sides by : .
(a) and ; (b)
03 The student computes the acceleration in part (b) by dividing change in velocity by the entire elapsed time span rather than the time interval between velocity measurements.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You divided by the instantaneous clock time instead of the elapsed duration between measurements .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used symmetric central differences across the full span to find instantaneous velocities at both time points.
You correctly calculated the velocity difference .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally placed the final time coordinate in the denominator instead of subtracting the initial time coordinate .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated acceleration as rather than strictly evaluating the elapsed interval . Always write out explicitly before dividing.
REASONING PATH
Your ACEpath teacher’s suggested approach- Elapsed Interval vs. Clock Reading
Average acceleration over a step requires dividing by the difference between two timestamps: .
Check whether your denominator represents a difference between two recorded times rather than a single clock reading.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the timestamps for the two known velocities: with , and with .
Calculate the elapsed time interval: .
Compute acceleration: .
Lock it in
What is the total elapsed time in the denominator of the symmetric central difference formula for when data is sampled every ?
. The interval spans from to , which gives .
Similar question
A spark timer records the position of a falling weight every . The recorded positions are and . Using a central difference centered at , calculate the instantaneous velocity .
Answer
. The total time span is . Thus, .
A motion cart produces position data , , , and . (a) Find and using central differences. (b) Find the average acceleration between and .
Answer
(a) , ; (b) . For (a), , so and . For (b), .
For a quadratic trajectory , discrete positions are recorded with time step . Show that the second finite difference formula yields the exact acceleration at .
Answer
. Evaluating positions at , , and : , , . The second difference is . Dividing by gives , matching .