Resources
In a university physics laboratory, a motorized dynamics cart equipped with an ultrasonic motion sensor accelerates uniformly from rest down an inclined track. Photogates positioned at and from the starting point record the cart's instantaneous velocities as and , respectively. Using the experimental data gathered between the two photogate flags, calculate the constant acceleration of the cart and the total time elapsed from the initial release (, ) until the cart reaches the second photogate at .
Answer and steps
Final answer
,
Steps
Calculate the Constant Acceleration Between the Photogates
To find the acceleration without knowing the time interval between the two photogates, use the kinematic relation connecting velocities and displacement under constant acceleration:
From the experimental measurements between the two photogates:
- Position at photogate 1:
- Position at photogate 2:
- Displacement between photogates:
- Velocity at photogate 1:
- Velocity at photogate 2:
Rearrange the kinematic equation to solve for :
Substitute the recorded values:
Determine the Total Time Elapsed from Release
The cart starts from rest at the top of the track, so:
- Initial position:
- Initial velocity:
- Acceleration:
- Final position:
Using the position-time relation for uniform acceleration:
Since and , the equation simplifies to:
Solving for :
Common Pitfall to Avoid
When calculating the total time from initial release, do not just calculate the transit time between the two photogates (). That only represents the time from to , whereas the question asks for the total elapsed time starting from the release point .
Typical errors
01 The student uses the total position coordinate x₂ instead of the displacement between photogates (x₂ - x₁) when finding acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The velocities and correspond to positions and . The kinematic formula connects the change in velocity squared with the displacement traversed between those two points, which is , not the total coordinate .
- Step 2Correct
Your reasoning to find total elapsed time from release was sound, but substituting the incorrect acceleration value led to an inaccurate final time.
WHAT YOU DID WELL
Compliments from Your TeacherYou selected appropriate kinematic relations for uniformly accelerated motion.
You performed accurate arithmetic and algebraic manipulations at each step.
You correctly identified the initial conditions at release as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the position coordinate in place of the displacement interval .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing a position coordinate with the displacement over the specific interval where the velocity changes from to . The kinematic identity strictly depends on the distance traveled between the initial and final velocity measurements.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match velocities to displacement
, where .
Always verify that the endpoints of your displacement interval match the exact locations where and were measured.
- Coordinate vs. Interval
Position equals displacement only when starting from the origin .
Check whether the initial velocity measurement occurred at the origin or at an offset position.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute displacement between photogates: .
Solve for constant acceleration: .
Determine total elapsed time from release to : .
,
02 The student calculates only the transit time between the two photogates instead of the total elapsed time from initial release.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You equated the total elapsed time to the transit time between photogates. The problem asks for the total time from the release at () to .
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the appropriate kinematic formula relating velocities, acceleration, and displacement to determine .
You correctly calculated the transit time between the two photogate locations.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the time elapsed between the two photogates with the total time elapsed from the initial release point.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing an intermediate sub-interval with the total duration measured from the initial state at .
REASONING PATH
Your ACEpath teacher’s suggested approach- Reference State Verification
Total elapsed time is always measured relative to the designated starting point (, , ), not between intermediate sensor flags.
Check whether the question asks for elapsed time over a sub-interval or total elapsed time from initial release.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify initial conditions at release: , , and .
Apply the position-time relation to the entire motion from to : .
Substitute known values: .
Solve for total time: .
,
03 The student uses linear velocity differences without squaring the velocities in the work-energy kinematic formula.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set up the relationship between velocity and displacement without squaring the velocities. The constant-acceleration kinematic equation connecting velocity and position is , which derives from work-energy principles or integrating .
- Step 2Correct
(or using )
Your method of setting from rest is conceptually correct, but your calculated time of is incorrect because it inherited the inaccurate acceleration value from Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the displacement between the two photogates as .
You correctly recognized that the cart started from rest (), allowing you to use to relate final velocity and total elapsed time.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou dropped the squares on the velocity terms in the time-independent kinematic equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the linear velocity difference from the definition of acceleration, , with the quadratic velocity relation for displacement, . Because both equations involve a velocity difference and acceleration, dropping the square is a frequent formula-recall error.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Dimensions of Kinematic Formulas
Every term in an equation must have identical physical units.
Notice that has units of . To match these units, the velocity side must be squared (, which has units of ), not linear velocity (, which has units of ).
- Pair the Independent Variable with the Correct Equation
Use when time is given or sought, and when position or displacement is given or sought without time.
Before substituting numbers, state whether the problem links velocity to time (linear) or velocity to position (quadratic).
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the correct time-independent kinematic relation: .
Substitute the photogate values: .
Evaluate the squares and solve for acceleration: .
Use the cart's motion from rest (, ) to position : .
Solve for total elapsed time: .
,
Lock it in
In the kinematic formula , what does represent?
, the displacement traveled strictly between the point where velocity is and the point where velocity is .
Similar question
A glider on an air track accelerates uniformly from rest at . It passes two sensors located at and with speeds and , respectively. Calculate the acceleration of the glider.
Answer
. Key steps: Identify . Use .
A test vehicle moving with constant acceleration passes marker at position traveling at and marker at position traveling at . Find the acceleration of the vehicle and the position where it started from rest.
Answer
, starting position . Key steps: Displacement between markers is . Acceleration is . From rest () to marker (): , so .
A cart is released from rest at on an inclined plane. It passes through photogate 1 at and photogate 2 at . The time to travel between the two photogates is . Determine the total time taken from release until the cart reaches photogate 2.
Answer
. Key steps: Since under constant acceleration from rest, and . Given , it follows that . The transit time is . Therefore, the total time to reach photogate 2 is .