Resources
In an introductory physics laboratory investigation, students measure the rotational inertia of an irregular rotor assembly mounted on a low-friction vertical axle. A light cord wrapped around the axle drum of radius carries a hanging mass . When released from rest, the hanging mass falls through a measured vertical distance in an average time of under gravitational acceleration . (a) Determine the linear downward acceleration of the falling mass. (b) Using Newton's second law for the linear and rotational motions ( and ), calculate the experimental moment of inertia of the rotating assembly.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Linear Downward Acceleration
- Identify the kinematic relationship:
The hanging mass begins from rest () and falls vertically through a displacement in time with constant acceleration . The kinematic equation is: - Solve for :
- Substitute the given values:
Part (b): Moment of Inertia of the Rotating Assembly
-
Find the cord tension ():
Applying Newton's second law to the downward motion of the hanging mass :Substitute the known values (, , and ):
- Relate torque to moment of inertia:
The tension exerts a torque on the axle drum of radius at a perpendicular angle: According to Newton's second law for rotation: Since the cord unwinds without slipping, the angular acceleration is related to the linear acceleration by : -
Solve for :
Common Pitfall: Do not assume the tension equals the full weight of the hanging mass (). Because the mass accelerates downward, . Neglecting the acceleration term in leads to an overestimate of the moment of inertia.
- Calculate :
Typical errors
01 The student assumes tension equals the hanging weight (T = mg) instead of accounting for the downward linear acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the hanging mass accelerates downward, the net force is not zero. Tension must be strictly less than gravity () rather than equal to static weight ().
- Step 3Correct
Your rotational dynamic equation and algebraic rearrangement for were completely correct, but the final value was slightly overestimated due to using instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou used the kinematic equation for motion from rest to find the correct linear acceleration.
You related torque to angular acceleration using .
You correctly used the non-slip condition and isolated the moment of inertia .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeAssuming tension equals for a falling mass.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the hanging mass as if it were in static equilibrium () rather than writing Newton's second law for the accelerating body ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the net force on accelerating bodies
If a body of mass accelerates downward with acceleration , Newton's second law requires .
Draw a free-body diagram for the hanging mass and isolate before substituting tension into the torque equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply Newton's second law to the falling mass: .
Substitute the numerical values: .
Substitute this tension into the isolated rotational inertia formula: .
02 The student forgets the factor of 2 from h = (1/2)at² when solving for acceleration, resulting in a value of a that is half the true value.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You omitted the factor of in the kinematic equation for an object accelerating from rest (). Solving for requires multiplying by , yielding .
- Step 2Correct
You correctly applied Newton's second law for the falling mass to write , but your result was affected by substituting the incorrect acceleration value from Step 1.
- Step 3Correct
Your algebraic derivation relating torque to moment of inertia () is completely correct, but substituting your halved value of roughly doubled your final calculated moment of inertia.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related the net force on the falling mass to its acceleration using .
You correctly expressed the torque equation and related angular acceleration to linear acceleration via .
You correctly rearranged the torque and force relations to isolate .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of when finding linear acceleration from rest.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated displacement under constant acceleration with the product of acceleration and time squared, forgetting the average velocity factor of that arises from integrating constant acceleration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Constant Acceleration Kinematics
For motion starting from rest (), vertical displacement is , so .
Always verify your kinematics equation before rearranging: remember that average velocity is , so .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate with the factor of : .
Compute the cord tension: .
Compute the experimental moment of inertia: (or using ).
(a) ; (b)
03 The student uses the relationship α = a·r instead of the correct relationship α = a/r when relating angular and linear acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You related linear and angular acceleration using instead of . Because , solving for angular acceleration gives . Substituting this into gives , which leads to .
- Step 4Correct
Your arithmetic followed directly from your formula , but the result is incorrect due to the substituted kinematic relation in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used kinematics to find the linear acceleration .
You correctly set up Newton's second law on the hanging mass to find the tension .
You correctly recognized that torque is given by .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the relationship with , substituting into the torque equation instead of dividing linear acceleration by the drum radius.
REASONING PATH
Your ACEpath teacher’s suggested approach- Connecting Linear and Angular Quantities
Tangential linear variables equal the angular variable multiplied by the radius: , , and . Therefore, .
Always verify the dimensions: has units of , while has units of , so you must divide by (in meters) to get .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the correct rolling-without-slipping condition into the torque equation: .
Solve for moment of inertia : .
Substitute the values: .
(a) ; (b)
Lock it in
What is the tension in a light string supporting a mass that accelerates downward with acceleration ?
. By Newton's second law, downward net force is , so tension is strictly less than weight.
Similar question
A light string wrapped around an axle of radius supports a hanging mass . If the mass accelerates downward at (), determine the tension in the cord and the resulting torque on the axle.
Answer
, . Key steps: ; .
A solid disk pulley of radius and moment of inertia is driven by a hanging mass . When released from rest, the mass drops in . Taking , find the linear downward acceleration and the moment of inertia of the pulley.
Answer
, . Key steps: ; ; .
A flywheel of radius and moment of inertia is connected to a falling mass . Derive a symbolic expression for the downward acceleration in terms of , , , and . Then, find the limiting value of the cord tension as the flywheel becomes frictionless and massless ().
Answer
, and . Key steps: Combine and to get . As , , meaning the mass is in free fall and string tension .