Resources
Water () is pumped upwards through an inclined conduit. At the lower intake (elevation ), the pipe has diameter , the flow speed is , and the gauge pressure measured by an external pressure transducer is . At the upper discharge point (elevation ), the pipe diameter narrows to . Taking and defining gauge pressure strictly as , calculate the gauge pressure at the upper outlet.
Answer and steps
Final answer
Steps
Determine the flow speed at the upper outlet
To find the gauge pressure at the upper outlet, apply the continuity equation for incompressible flow followed by Bernoulli's principle.
For an incompressible liquid flowing steadily through a pipe of changing cross-sectional area, the volume flow rate remains constant:
Because the cross-sectional area of a circular pipe is proportional to the square of its diameter (), the ratio simplifies to:
Substitute the given values:
Apply Bernoulli's equation
Bernoulli's equation connects pressure, fluid velocity, and elevation along a streamline:
Since absolute pressure is related to gauge pressure by , subtracting atmospheric pressure from both sides allows Bernoulli's equation to be written directly in terms of gauge pressures:
Rearrange to solve for :
Calculate the individual energy terms per unit volume
- Dynamic pressure difference (kinetic energy term):
- Hydrostatic pressure difference (potential energy term):
Compute the upper gauge pressure
Substitute the calculated terms back into the rearranged equation:
Rounding to three significant figures gives:
Typical errors
01 The student scales velocity linearly with diameter rather than diameter squared in the continuity equation, setting v2 = v1*(d1/d2) = 5.00 m/s.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the cross-sectional area of a circular pipe is proportional to the square of its diameter (), the continuity equation requires velocity to scale with , not .
- Step 2
- Step 3Correct
Your arithmetic was carried out accurately, but this value is affected by your earlier incorrect velocity of .
- Step 4
- Step 5Correct
This result follows correctly from your intermediate numbers, but it differs from the true value due to the velocity error in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that gauge pressure can be used directly in Bernoulli's equation.
You properly rearranged Bernoulli's equation to isolate the discharge gauge pressure.
You calculated the gravitational potential pressure term with complete precision.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou forgot to square the diameter ratio when converting the area ratio in the continuity equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing one-dimensional length ratios with two-dimensional cross-sectional area ratios when applying the continuity equation for circular pipes.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Continuity Scaling
For a circular duct, , so the area ratio is .
Always square the diameter (or radius) ratio when solving for flow speed: .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the continuity equation using circular cross-sectional areas: .
Compute the dynamic pressure change: .
Combine with the initial gauge pressure and hydrostatic loss: .
02 The student adds the elevation potential energy term instead of subtracting it when solving for the pressure at the higher elevation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When rearranging Bernoulli's equation with , moving to the other side requires subtracting it. Fluid moving upward gains potential energy at the expense of pressure.
- Step 3
- Step 4Correct
Because of the sign error on the hydrostatic term in step 2, adding yielded instead of the expected .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied the conservation of mass to relate pipe diameter to fluid velocity.
You recognized that Bernoulli's equation can be evaluated directly with gauge pressures.
You performed the arithmetic for the dynamic pressure and gravitational terms with complete precision.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally wrote instead of when isolating .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated elevation gain as contributing positively to downstream static pressure, whereas climbing in a gravitational field consumes pressure head to supply gravitational potential energy.
REASONING PATH
Your ACEpath teacher’s suggested approach- Physical Reality Check for Elevation
Moving upward along a streamline in steady flow always decreases static pressure if velocity does not decrease sufficiently: .
Always verify that your isolated pressure formula subtracts when moving to a higher elevation.
- Algebraic Balancing of Conserved Quantities
.
Write the full un-rearranged Bernoulli equation first, then subtract terms systematically from both sides.
CORRECTED PATH
ACEpath Teacher's DemonstrationStart from Bernoulli's equation:
Set and subtract the kinetic and potential terms at point 2:
Substitute the numerical values:
03 The student forgets to square the velocities when calculating the kinetic energy density change in Bernoulli's equation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You forgot to square the velocities in the kinetic energy density term of Bernoulli's equation. The dynamic pressure difference is , not .
- Step 3
- Step 4Correct
Your subtraction followed your previous line consistently, but the final numerical value is incorrect due to the unsquared velocities in the kinetic term.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related the conduit diameters to fluid velocities using the equation of continuity.
You set up the elevation head difference and converted all units accurately.
You recognized that Bernoulli's equation can be applied directly using gauge pressures.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of when setting up the kinetic energy term.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisThe dynamic pressure term in Bernoulli's principle represents kinetic energy per unit volume, which is proportional to velocity squared (). Confusing linear velocity difference with quadratic velocity difference drastically underestimates the pressure drop caused by fluid acceleration.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimension of kinetic energy density
Kinetic energy per unit volume is , having units of .
Always verify that every velocity factor in Bernoulli's equation carries an exponent of 2 before evaluating numerical differences.
- Difference of squares vs. square of difference
The change in dynamic pressure between two points is , never .
Calculate and individually before finding their difference.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the squared velocities: and .
Evaluate the dynamic pressure difference: .
Substitute into Bernoulli's equation: .
Lock it in
How does fluid speed scale with pipe diameter for steady incompressible flow in a circular pipe?
Speed scales inversely with diameter squared: , because and .
Similar question
Water flows horizontally through a pipe that narrows from an inner diameter of to . If the flow speed in the wider section is , calculate the flow speed in the narrow section.
Answer
. Using continuity for circular pipes: .
A horizontal pipe carries water () from a section with diameter and gauge pressure at speed into a constriction of diameter . Find the gauge pressure in the constriction.
Answer
. First, . Then by Bernoulli's equation with : .
Water () is pumped up an incline through a pipe. At the base (, ), the flow speed is and gauge pressure is . At the outlet (, ), determine the gauge pressure. Take .
Answer
. Outlet velocity: . Dynamic term: . Elevation head term: . Gauge pressure: .