Resources

A rectangular generator coil (15.0 cm×25.0 cm15.0\text{ cm} \times 25.0\text{ cm}, N=180 turnsN = 180\text{ turns}) rotates in a uniform magnetic field B⃗=0.400 T  k^\vec{B} = 0.400\text{ T}\;\hat{k}. At t=0 st = 0\text{ s}, the coil's normal unit vector points along the positive zz-axis (n^(0)=k^\hat{n}(0) = \hat{k}). The coil rotates counterclockwise about the xx-axis at ω=50.0 rad/s\omega = 50.0\text{ rad/s} such that the angle of the normal is θ(t)=ωt\theta(t) = \omega t. The generator output is wired to the primary coil of an isolating transformer (Np=100 turnsN_p = 100\text{ turns}, Ns=200 turnsN_s = 200\text{ turns}) wound around an iron toroid according to the standard dot convention: current entering the dotted primary terminal produces magnetic flux in the core that induces an emf with high potential at the dotted secondary terminal. (a) Applying Faraday's law E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}, write the exact mathematical expression for the induced instantaneous generator emf E(t)\mathcal{E}(t) as a function of time. (b) Determine the instantaneous secondary voltage vs(t)v_s(t) when t=π150 st = \frac{\pi}{150}\text{ s}.

Answer and steps

Final answer

(a) E(t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = (135\text{ V})\sin(50.0 t); (b) vs(π150 s)=+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = +234\text{ V}

Steps

Part (a): Mathematical Expression for the Generator emf

  1. Calculate the area of the rectangular coil: A=(0.150 m)×(0.250 m)=0.0375 m2A = (0.150\text{ m}) \times (0.250\text{ m}) = 0.0375\text{ m}^2
  2. Determine the magnetic flux through the coil: At time tt, the angle between the normal vector n^(t)\hat{n}(t) and the constant magnetic field B⃗=B k^\vec{B} = B\,\hat{k} is θ(t)=ωt\theta(t) = \omega t. The magnetic flux Φ1(t)\Phi_{1}(t) through a single turn is: Φ1(t)=B⃗⋅A⃗=BAcos⁡(ωt)\Phi_{1}(t) = \vec{B} \cdot \vec{A} = B A \cos(\omega t)

    For a coil of NN turns, the total magnetic flux linkage is: ΦB(t)=NBAcos⁡(ωt)\Phi_B(t) = N B A \cos(\omega t)

  3. Apply Faraday's law of induction: E(t)=−dΦBdt=−ddt[NBAcos⁡(ωt)]=NBAωsin⁡(ωt)\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}\bigl[N B A \cos(\omega t)\bigr] = N B A \omega \sin(\omega t)
  4. Evaluate the peak emf E0=NBAω\mathcal{E}_0 = N B A \omega: E0=(180)(0.400 T)(0.0375 m2)(50.0 rad/s)=135 V\mathcal{E}_0 = (180)(0.400\text{ T})(0.0375\text{ m}^2)(50.0\text{ rad/s}) = 135\text{ V}

    Substituting E0\mathcal{E}_0 and ω\omega into the expression gives: E(t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = (135\text{ V})\sin(50.0 t)


Part (b): Instantaneous Secondary Voltage at t=π150 st = \frac{\pi}{150}\text{ s}

  1. Find the generator emf (primary voltage vpv_p) at t=π150 st = \frac{\pi}{150}\text{ s}: The phase angle is: θ=ωt=(50.0 rad/s)(π150 s)=π3 rad=60∘\theta = \omega t = (50.0\text{ rad/s})\left(\frac{\pi}{150}\text{ s}\right) = \frac{\pi}{3}\text{ rad} = 60^\circ

    Evaluating the primary voltage: vp(π150 s)=(135 V)sin⁡(π3)=(135 V)(32)≈116.91 Vv_p\left(\frac{\pi}{150}\text{ s}\right) = (135\text{ V})\sin\left(\frac{\pi}{3}\right) = (135\text{ V})\left(\frac{\sqrt{3}}{2}\right) \approx 116.91\text{ V}

  2. Apply the ideal transformer voltage relationship: An ideal transformer steps voltage up or down in direct proportion to the turns ratio: vs(t)vp(t)=NsNp\frac{v_s(t)}{v_p(t)} = \frac{N_s}{N_p}

    With Np=100 turnsN_p = 100\text{ turns} and Ns=200 turnsN_s = 200\text{ turns}, the turns ratio is: NsNp=200100=2\frac{N_s}{N_p} = \frac{200}{100} = 2

    Because the coil connections respect the dot convention (in-phase transformation), the instantaneous secondary voltage is: vs(π150 s)=2×116.91 V≈+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = 2 \times 116.91\text{ V} \approx +234\text{ V}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets the negative sign in Faraday's law E = -dΦ_B/dt, resulting in a negative sine expression for the induced emf and secondary voltage.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=0.150×0.250=0.0375 m2  ⟹  ΦB(t)=NBAcos⁡(ωt)=180×0.400×0.0375×cos⁡(50.0t)=2.70cos⁡(50.0t) WbA = 0.150 \times 0.250 = 0.0375\text{ m}^2 \implies \Phi_B(t) = N B A \cos(\omega t) = 180 \times 0.400 \times 0.0375 \times \cos(50.0t) = 2.70\cos(50.0t)\text{ Wb}

  2. Step 2

    E(t)=dΦBdt=−135sin⁡(50.0t) V\mathcal{E}(t) = \frac{d\Phi_B}{dt} = -135\sin(50.0t)\text{ V}

    Correct

    E(t)=−dΦBdt=−ddt[2.70cos⁡(50.0t)]=(135 V)sin⁡(50.0t)\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}[2.70\cos(50.0t)] = (135\text{ V})\sin(50.0t)

    Faraday's law includes a leading negative sign representing Lenz's law: E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}. Differentiating cos⁡(50.0t)\cos(50.0t) introduces a factor of −50.0sin⁡(50.0t)-50.0\sin(50.0t), so the two negative signs cancel to yield positive +135sin⁡(50.0t) V+135\sin(50.0t)\text{ V}.

  3. Step 3

    vs(t)=(NsNp)E(t)=−270sin⁡(50.0t) V  ⟹  vs(π150)=−270sin⁡(π3)≈−234 Vv_s(t) = \left(\frac{N_s}{N_p}\right)\mathcal{E}(t) = -270\sin(50.0t)\text{ V} \implies v_s\left(\frac{\pi}{150}\right) = -270\sin\left(\frac{\pi}{3}\right) \approx -234\text{ V}

    Correct

    vs(t)=(NsNp)E(t)=(270 V)sin⁡(50.0t)  ⟹  vs(π150)=270sin⁡(π3)≈+234 Vv_s(t) = \left(\frac{N_s}{N_p}\right)\mathcal{E}(t) = (270\text{ V})\sin(50.0t) \implies v_s\left(\frac{\pi}{150}\right) = 270\sin\left(\frac{\pi}{3}\right) \approx +234\text{ V}

    Your transformer voltage ratio and evaluation of the phase angle at t=π150 st = \frac{\pi}{150}\text{ s} were completely correct, but the negative sign from Step 2 carried through to the final answer.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately converted coil dimensions to SI units and calculated the cross-sectional area.

You correctly expressed the total magnetic flux linkage as a cosine function of time.

You applied the ideal transformer turns ratio vsvp=NsNp\frac{v_s}{v_p} = \frac{N_s}{N_p} and evaluated the trigonometric angle accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Lenz's Law Negative Sign

You differentiated the flux function correctly but wrote E=dΦBdt\mathcal{E} = \frac{d\Phi_B}{dt} rather than E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the foundational negative sign in Faraday's law E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}, which represents Lenz's opposition to flux changes.

REASONING PATH
Your ACEpath teacher’s suggested approach
Faraday-Lenz Law Formulation
  • The induced electromotive force around a closed loop is E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}.

  • Always write down the full formula with the negative sign before taking derivatives.

Derivative Sign Tracking
  • ddt[cos⁡(ωt)]=−ωsin⁡(ωt)\frac{d}{dt}[\cos(\omega t)] = -\omega \sin(\omega t), so −ddt[cos⁡(ωt)]=+ωsin⁡(ωt)-\frac{d}{dt}[\cos(\omega t)] = +\omega \sin(\omega t).

  • Double-check the product of negative signs whenever differentiating a cosine flux function.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Faraday's law with the correct negative sign: E(t)=−dΦBdt=−ddt[2.70cos⁡(50.0t)]=−(−2.70×50.0sin⁡(50.0t))=(135 V)sin⁡(50.0t)\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}\bigl[2.70\cos(50.0t)\bigr] = -\bigl(-2.70 \times 50.0\sin(50.0t)\bigr) = (135\text{ V})\sin(50.0t).

  2. Apply the in-phase secondary transformer relation with NsNp=200100=2\frac{N_s}{N_p} = \frac{200}{100} = 2: vs(t)=2E(t)=(270 V)sin⁡(50.0t)v_s(t) = 2\mathcal{E}(t) = (270\text{ V})\sin(50.0t).

  3. Substitute t=π150 st = \frac{\pi}{150}\text{ s}: vs(π150)=270sin⁡(π3)=270(32)≈+234 Vv_s\left(\frac{\pi}{150}\right) = 270\sin\left(\frac{\pi}{3}\right) = 270\left(\frac{\sqrt{3}}{2}\right) \approx +234\text{ V}.

Final answer

(a) E(t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = (135\text{ V})\sin(50.0 t); (b) vs(π150 s)=+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = +234\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the physical meaning of the negative sign in Faraday's law as Lenz's law.

  • Practice tracking signs carefully when taking time derivatives of sinusoidal flux expressions.

  • Verify dot-convention polarity rules when linking rotating generator coils to isolating transformers.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the transformer turns ratio as N_p/N_s instead of N_s/N_p, halving the generator voltage rather than doubling it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=0.150×0.250=0.0375 m2  ⟹  ΦB(t)=180×0.400×0.0375×cos⁡(50.0t)=2.70cos⁡(50.0t) WbA = 0.150 \times 0.250 = 0.0375\text{ m}^2 \implies \Phi_B(t) = 180 \times 0.400 \times 0.0375 \times \cos(50.0t) = 2.70\cos(50.0t)\text{ Wb}

  2. Step 2

    E(t)=−dΦBdt=135sin⁡(50.0t) V\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = 135\sin(50.0t)\text{ V}

  3. Step 3

    vs(t)=NpNsE(t)=100200×135sin⁡(50.0t)=67.5sin⁡(50.0t) Vv_s(t) = \frac{N_p}{N_s} \mathcal{E}(t) = \frac{100}{200} \times 135\sin(50.0t) = 67.5\sin(50.0t)\text{ V}

    Correct

    vs(t)=NsNpE(t)=200100×135sin⁡(50.0t)=270sin⁡(50.0t) Vv_s(t) = \frac{N_s}{N_p} \mathcal{E}(t) = \frac{200}{100} \times 135\sin(50.0t) = 270\sin(50.0t)\text{ V}

    You inverted the ideal transformer equation. The secondary voltage is directly proportional to the secondary turns: vs/vp=Ns/Npv_s / v_p = N_s / N_p, so the turns ratio must be NsNp=200100=2\frac{N_s}{N_p} = \frac{200}{100} = 2.

  4. Step 4

    At t=π150 s,  ωt=π3 rad  ⟹  vs(π150)=67.5sin⁡(π3)=67.5(32)≈58.5 V\text{At } t = \frac{\pi}{150}\text{ s},\; \omega t = \frac{\pi}{3}\text{ rad} \implies v_s\left(\frac{\pi}{150}\right) = 67.5\sin\left(\frac{\pi}{3}\right) = 67.5\left(\frac{\sqrt{3}}{2}\right) \approx 58.5\text{ V}

    Correct

    vs(π150)=270sin⁡(π3)=270(32)≈+234 Vv_s\left(\frac{\pi}{150}\right) = 270\sin\left(\frac{\pi}{3}\right) = 270\left(\frac{\sqrt{3}}{2}\right) \approx +234\text{ V}

    You correctly evaluated the phase angle ωt=π3 rad\omega t = \frac{\pi}{3}\text{ rad} and its sine, but your numerical answer was halved due to the inverted turns ratio in Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the coil's area and total flux linkage accurately.

You correctly used Faraday's law of induction to find the instantaneous generator emf for part (a).

You substituted the specified time to calculate the phase angle ωt\omega t correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Transformer Turns Ratio

You set the transformer voltage transformation to Np/NsN_p / N_s rather than Ns/NpN_s / N_p.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the voltage ratio with the current ratio in an ideal transformer. While currents are inversely proportional to turns (is/ip=Np/Nsi_s / i_p = N_p / N_s), voltages are directly proportional to turns (vs/vp=Ns/Npv_s / v_p = N_s / N_p) because each turn encloses the exact same rate of change of magnetic core flux.

REASONING PATH
Your ACEpath teacher’s suggested approach
Per-Turn Induced EMF Principle
  • Every individual turn on an ideal transformer core experiences the same shared core flux Φcore\Phi_{\text{core}}, so the voltage per turn is identical: vpNp=vsNs=−dΦcoredt\frac{v_p}{N_p} = \frac{v_s}{N_s} = -\frac{d\Phi_{\text{core}}}{dt}.

  • Rearrange vsNs=vpNp\frac{v_s}{N_s} = \frac{v_p}{N_p} directly to vs=vp(NsNp)v_s = v_p \left(\frac{N_s}{N_p}\right) before substituting any numbers.

Step-Up vs. Step-Down Sanity Check
  • If a coil has more turns (Ns>NpN_s > N_p), it must produce a higher voltage (vs>vpv_s > v_p).

  • Compare NsN_s and NpN_p qualitatively first: with Ns=200>Np=100N_s = 200 > N_p = 100, the transformer is a step-up transformer and must double the voltage, not halve it.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the transformer voltage relationship: vs(t)=(NsNp)vp(t)=(200100)[135sin⁡(50.0t) V]=270sin⁡(50.0t) Vv_s(t) = \left(\frac{N_s}{N_p}\right) v_p(t) = \left(\frac{200}{100}\right) [135\sin(50.0t)\text{ V}] = 270\sin(50.0t)\text{ V}.

  2. Evaluate the secondary voltage at t=π150 st = \frac{\pi}{150}\text{ s}: ωt=(50.0)(π150)=π3 rad\omega t = (50.0)\left(\frac{\pi}{150}\right) = \frac{\pi}{3}\text{ rad}.

  3. Compute the numerical value: vs=270sin⁡(π3)=270×32≈+234 Vv_s = 270\sin\left(\frac{\pi}{3}\right) = 270 \times \frac{\sqrt{3}}{2} \approx +234\text{ V}.

Final answer

vs(π150 s)=+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = +234\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the direct relationship for voltage: more turns yield more voltage (V∝NV \propto N).

  • Perform a quick step-up/step-down sanity check on the turns ratio before continuing with numerical evaluation.

  • Review how Faraday's law applied to a shared core naturally equates the voltage-per-turn in both primary and secondary windings.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to multiply by the angular frequency ω when differentiating cos(ωt) with respect to time.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.150×0.250=0.0375 m2  ⟹  ΦB(t)=180×0.400×0.0375×cos⁡(50.0t)=2.70cos⁡(50.0t) WbA = 0.150 \times 0.250 = 0.0375\text{ m}^2 \implies \Phi_B(t) = 180 \times 0.400 \times 0.0375 \times \cos(50.0t) = 2.70\cos(50.0t)\text{ Wb}

  2. Step 2

    E(t)=−dΦBdt=2.70sin⁡(50.0t) VE(t) = -\frac{d\Phi_B}{dt} = 2.70\sin(50.0t)\text{ V}

    Correct

    E(t)=−dΦBdt=−ddt[2.70cos⁡(50.0t)]=2.70×50.0sin⁡(50.0t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}[2.70\cos(50.0t)] = 2.70 \times 50.0\sin(50.0t) = (135\text{ V})\sin(50.0t)

    When differentiating cos⁡(50.0t)\cos(50.0t) with respect to time tt, the chain rule requires multiplying by the derivative of the inside angle, ddt(50.0t)=50.0 rad/s\frac{d}{dt}(50.0t) = 50.0\text{ rad/s}.

  3. Step 3

    vs(t)=NsNp×E(t)=2×2.70sin⁡(50.0t)=5.40sin⁡(50.0t) Vv_s(t) = \frac{N_s}{N_p} \times E(t) = 2 \times 2.70\sin(50.0t) = 5.40\sin(50.0t)\text{ V}

    Correct

    vs(t)=NsNpE(t)=2×135sin⁡(50.0t)=(270 V)sin⁡(50.0t)v_s(t) = \frac{N_s}{N_p}\mathcal{E}(t) = 2 \times 135\sin(50.0t) = (270\text{ V})\sin(50.0t)

    You correctly applied the transformer turns ratio NsNp=2\frac{N_s}{N_p} = 2, but this step inherits the missing factor of 50.050.0 from your emf expression.

  4. Step 4

    At t=π150 s, ωt=50.0×(π150)=π3 rad  ⟹  vs(π150)=5.40sin⁡(π3)=5.40×32≈4.68 V\text{At } t = \frac{\pi}{150}\text{ s},\ \omega t = 50.0 \times \left(\frac{\pi}{150}\right) = \frac{\pi}{3}\text{ rad} \implies v_s\left(\frac{\pi}{150}\right) = 5.40\sin\left(\frac{\pi}{3}\right) = 5.40 \times \frac{\sqrt{3}}{2} \approx 4.68\text{ V}

    Correct

    vs(π150 s)=270sin⁡(π3)=270×32≈+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = 270\sin\left(\frac{\pi}{3}\right) = 270 \times \frac{\sqrt{3}}{2} \approx +234\text{ V}

    You evaluated the phase angle ωt=π3 rad\omega t = \frac{\pi}{3}\text{ rad} accurately, but the numerical result is off by a factor of 50.050.0 due to the earlier differentiation error.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the area of the rotating coil accurately.

You set up the magnetic flux linkage function with the correct initial cosine dependence.

You applied the transformer turns ratio relationship correctly.

You evaluated the phase angle at the target time correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Chain Rule Omission in Faraday's Law

You differentiated cos⁡(ωt)\cos(\omega t) as if the argument were simply tt, forgetting to multiply by the inner derivative ω\omega.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the chain rule when differentiating harmonic time functions cos⁡(ωt)\cos(\omega t) or sin⁡(ωt)\sin(\omega t) leads to omitting the angular frequency ω\omega in the amplitude of induced emf.

REASONING PATH
Your ACEpath teacher’s suggested approach
Chain Rule for Harmonic Angles
  • ddt[cos⁡(ωt)]=−ωsin⁡(ωt)\frac{d}{dt}[\cos(\omega t)] = -\omega\sin(\omega t)

  • Always multiply the amplitude by ω\omega whenever you differentiate a trigonometric function with an angular rate inside.

Dimensional Consistency Check
  • [E]=[ΦB]⋅[ω]=Wb⋅s−1=V[\mathcal{E}] = [\Phi_B] \cdot [\omega] = \text{Wb} \cdot \text{s}^{-1} = \text{V}

  • Check that the peak emf E0=NBAω\mathcal{E}_0 = N B A \omega includes ω\omega so that its unit evaluates to volts (1 Wb/s=1 V1\text{ Wb/s} = 1\text{ V}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the chain rule: E(t)=−ddt[2.70cos⁡(50.0t)]=2.70×50.0sin⁡(50.0t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = -\frac{d}{dt}[2.70\cos(50.0t)] = 2.70 \times 50.0\sin(50.0t) = (135\text{ V})\sin(50.0t).

  2. Relate primary voltage to secondary voltage: vs(t)=NsNpE(t)=2×135sin⁡(50.0t)=(270 V)sin⁡(50.0t)v_s(t) = \frac{N_s}{N_p}\mathcal{E}(t) = 2 \times 135\sin(50.0t) = (270\text{ V})\sin(50.0t).

  3. Evaluate at t=π150 st = \frac{\pi}{150}\text{ s}: vs(π150 s)=270sin⁡(π3)=270×32≈+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = 270\sin\left(\frac{\pi}{3}\right) = 270 \times \frac{\sqrt{3}}{2} \approx +234\text{ V}.

Final answer

(a) E(t)=(135 V)sin⁡(50.0t)\mathcal{E}(t) = (135\text{ V})\sin(50.0 t); (b) vs(π150 s)=+234 Vv_s\left(\frac{\pi}{150}\text{ s}\right) = +234\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the chain rule for time derivatives of sinusoids: ddt[cos⁡(ωt)]=−ωsin⁡(ωt)\frac{d}{dt}[\cos(\omega t)] = -\omega\sin(\omega t).

  • Check units on induced quantities: peak generator emf must have units of T⋅m2⋅rad/s=V\text{T} \cdot \text{m}^2 \cdot \text{rad/s} = \text{V}.

  • Practice problems combining rotating generators and step-up/step-down transformers.

Lock it in

Similar question

01

A 50-turn coil with an area of 0.020 m20.020\text{ m}^2 rotates at ω=100 rad/s\omega = 100\text{ rad/s} in a constant field of B=0.30 TB = 0.30\text{ T}. If the coil's normal vector is parallel to B⃗\vec{B} at t=0 st = 0\text{ s}, find the exact expression for the induced emf E(t)\mathcal{E}(t) using Faraday's law.

Answer
  1. Peak flux linkage: NBA=50×0.30×0.020=0.30 WbN B A = 50 \times 0.30 \times 0.020 = 0.30\text{ Wb}.
  2. Flux: ΦB(t)=0.30cos⁡(100t) Wb\Phi_B(t) = 0.30\cos(100t)\text{ Wb}.
  3. Faraday's law: E(t)=−dΦBdt=−ddt[0.30cos⁡(100t)]=(30 V)sin⁡(100t)\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}[0.30\cos(100t)] = (30\text{ V})\sin(100t).
02

An AC generator outputs an instantaneous voltage vp(t)=(120 V)sin⁡(60πt)v_p(t) = (120\text{ V})\sin(60\pi t) to a step-up transformer with Np=80 turnsN_p = 80\text{ turns} and Ns=400 turnsN_s = 400\text{ turns}. Assuming an in-phase dot convention, find the instantaneous secondary voltage vs(t)v_s(t) at t=1360 st = \frac{1}{360}\text{ s}.

Answer
  1. Turns ratio: NsNp=40080=5\frac{N_s}{N_p} = \frac{400}{80} = 5.
  2. Secondary voltage function: vs(t)=5×120sin⁡(60πt)=(600 V)sin⁡(60πt)v_s(t) = 5 \times 120\sin(60\pi t) = (600\text{ V})\sin(60\pi t).
  3. Evaluate at t=1360 st = \frac{1}{360}\text{ s}: θ=60π×1360=π6 rad\theta = 60\pi \times \frac{1}{360} = \frac{\pi}{6}\text{ rad}, so vs=600sin⁡(π6)=+300 Vv_s = 600\sin\left(\frac{\pi}{6}\right) = +300\text{ V}.
03

A single circular loop of radius r=10.0 cmr = 10.0\text{ cm} lies in the xyxy-plane. A spatially uniform magnetic field is directed along the zz-axis with time variation Bz(t)=B0e−αtB_z(t) = B_0 e^{-\alpha t}, where B0=0.500 TB_0 = 0.500\text{ T} and α=4.00 s−1\alpha = 4.00\text{ s}^{-1}. Taking the surface normal along +k^+\hat{k}, find the induced emf E(t)\mathcal{E}(t) at t=0.250 st = 0.250\text{ s}.

Answer
  1. Area: A=πr2=π(0.100)2=0.010π m2A = \pi r^2 = \pi (0.100)^2 = 0.010\pi\text{ m}^2.
  2. Flux: ΦB(t)=Bz(t)A=0.005πe−4.00t Wb\Phi_B(t) = B_z(t) A = 0.005\pi e^{-4.00t}\text{ Wb}.
  3. Differentiate: dΦBdt=−4.00×(0.005π)e−4.00t=−0.020πe−4.00t V\frac{d\Phi_B}{dt} = -4.00 \times (0.005\pi) e^{-4.00t} = -0.020\pi e^{-4.00t}\text{ V}.
  4. Faraday's law: E(t)=−dΦBdt=+0.020πe−4.00t V\mathcal{E}(t) = -\frac{d\Phi_B}{dt} = +0.020\pi e^{-4.00t}\text{ V}.
  5. At t=0.250 st = 0.250\text{ s}: E(0.250)=0.020πe−1.00≈+0.0231 V\mathcal{E}(0.250) = 0.020\pi e^{-1.00} \approx +0.0231\text{ V} (or +23.1 mV+23.1\text{ mV}).
Loading workspace…