Resources
A student attempts to calculate the final equilibrium temperature when a cold block of copper (, ) at is placed into warm water (, ) at . The student incorrectly writes the heat conservation equation as due to a sign convention confusion, yielding a nonsensical temperature. State the correct formal thermal conservation expression using consistent temperature differences , and solve for the correct final equilibrium temperature and the net heat transferred from the water to the copper.
Answer and steps
Final answer
Expression: ; ,
Steps
Correct Thermal Conservation Equation
In an isolated system, the sum of all heat gained and lost equals zero:
Heat exchange for any substance undergoing a temperature change without a phase change is given by: where the change in temperature is defined consistently as .
When this standard definition is used:
- A substance absorbing heat warms up (), so and .
- A substance releasing heat cools down (), so and .
The student incorrectly mixed signs by writing instead of . The correct formal expression is:
Solving for the Final Equilibrium Temperature
First, compute the heat capacities () of the copper and water:
- For copper:
- For water:
Substitute these values into the conservation equation:
Expand and group the terms:
Solve for :
Calculating the Heat Transferred
The net energy transferred from the warm water to the cold copper block is equal to the heat absorbed by the copper:
(Alternatively, checking with the water: , verifying that heat lost by the water equals heat gained by the copper).
Typical errors
01 The student confuses the specific heat capacities of copper and water when substituting them into the equation, leading to an incorrect equilibrium temperature and heat transferred.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You swapped the specific heat capacities: you paired water's specific heat () with copper and copper's specific heat () with water.
- Step 3Correct
Your algebraic rearrangement and arithmetic were carried out correctly, but the resulting equilibrium temperature is incorrect because of the swapped specific heat values from Step 2.
- Step 4Correct
You correctly set up the formula for heat absorbed by the copper, but evaluating it with the wrong specific heat and propagated led to an incorrect value.
WHAT YOU DID WELL
Compliments from Your TeacherYou stated the correct formal conservation of energy expression with consistent signs.
You performed linear algebraic expansion and solved for the unknown variable accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou interchanged the physical constants and during numerical substitution, which gave copper an artificially high heat capacity compared to water.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match constants to subscripts before evaluating
Every parameter in must carry the same subscript corresponding to that specific material.
Write out a dedicated given-values table (e.g., , ) and cross-check each term as you substitute.
- Perform a physical plausibility check on $T_f$
Water has a much higher specific heat capacity than most metals; equal or comparable masses of water dominate the final equilibrium temperature.
Since water has roughly ten times the heat capacity of copper here, should be much closer to than to .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the correct specific heat values: .
Simplify the coefficients: .
Expand and group terms: .
Solve for equilibrium temperature: .
Calculate heat transferred to the copper: .
,
02 The student omits the mass of copper in the heat capacity term, using only c_Cu rather than m_Cu c_Cu, which skews the final equilibrium temperature.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the mass of copper (), substituting only the specific heat capacity instead of .
- Step 3Correct
Your algebraic solving steps are correct based on your substituted equation, but the numerical result is skewed because of the missing mass factor.
- Step 4Correct
You carried forward both the omitted copper mass and the incorrect equilibrium temperature into the final heat calculation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set up the thermal conservation equation using consistent temperature differences .
You correctly substituted the values for the water component (, ).
You maintained clean and accurate algebraic steps when expanding and solving for .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote rather than when substituting for copper's heat capacity.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing specific heat capacity with total heat capacity , leading to an accidental omission of the mass factor for one of the substances.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check dimensions of thermal coefficients
Heat transferred is , where has units of . Specific heat has units of and must be multiplied by mass in kilograms.
Always compute and write out explicitly for each substance before substituting into the equation.
- Reasonableness check on equilibrium temperature
The equilibrium temperature lies closer to the temperature of the substance with the larger heat capacity ().
Notice that water has while copper has . Since water dominates by a factor of over , must be much closer to than to .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the complete product into the conservation equation: .
Expand terms: .
Combine like terms: , giving .
Calculate transferred heat: .
Expression: ; ,
Lock it in
In calorimetry, how is each substance's heat capacity defined, and why must subscripts match strictly?
, where and belong to that specific material. Swapping specific heat capacities inverts which substance resists temperature change more.
Similar question
An aluminum block (, ) at is placed into of water () at . Find the final equilibrium temperature .
Answer
. Setup: .
A piece of lead at is dropped into of water at . The final temperature is . Assuming no heat loss to surroundings, calculate the specific heat capacity of lead (take ).
Answer
. Setup: . Then .
An unknown metal cylinder of mass at is placed in an insulated calorimeter containing of water at . The container itself is made of of copper (). If the final equilibrium temperature of the system is , find the specific heat capacity of the unknown metal.
Answer
. Setup: Total heat absorbed by water and copper container is . Then .