Resources

In a coal-fired thermal generation plant, chemical potential energy stored in bituminous coal is converted to thermal energy in a boiler, transferred as enthalpy to superheated steam, converted into rotational kinetic energy across high-pressure and low-pressure steam turbine stages, and ultimately transformed into grid electrical energy. The plant consumes coal with a specific heat of combustion of ΔHc=2.80×107 J/kg\Delta H_c = 2.80 \times 10^7\text{ J/kg} at a steady rate of Rm=65.0 kg/sR_m = 65.0\text{ kg/s}. The steam generation system transfers heat into working steam with a boiler efficiency of ηboiler=86.0%\eta_{\text{boiler}} = 86.0\%. The turbine-generator assembly delivers a net electrical output of Pelec=635 MWP_{\text{elec}} = 635\text{ MW}. Rather than solving for power, determine the overall thermal-to-electrical thermal cycle efficiency ηcycle\eta_{\text{cycle}} (the efficiency of converting thermal energy absorbed by steam into net electrical work), and state the thermodynamic sink to which the remaining energy is rejected.

Answer and steps

Final answer

ηcycle=40.6%\eta_{\text{cycle}} = 40.6\%; the remaining unrecovered thermal energy (9.30×108 W9.30 \times 10^8\text{ W}) is rejected to the environment via cooling towers/condenser cooling water as low-grade thermal internal energy in accordance with the second law of thermodynamics.

Steps

01

Calculate the Total Thermal Power Released by Fuel Combustion

The chemical power input (Pin, fuelP_{\text{in, fuel}}) released by burning coal is the product of the mass consumption rate (RmR_m) and the specific heat of combustion (ΔHc\Delta H_c):

Pin, fuel=Rm⋅ΔHcP_{\text{in, fuel}} = R_m \cdot \Delta H_c

Substitute the given values:

Pin, fuel=(65.0 kg/s)(2.80×107 J/kg)=1.820×109 W=1820 MWP_{\text{in, fuel}} = (65.0\text{ kg/s})(2.80 \times 10^7\text{ J/kg}) = 1.820 \times 10^9\text{ W} = 1820\text{ MW}


02

Determine the Heat Rate Absorbed by the Steam

The boiler transfers heat to the working fluid (steam) with an efficiency ηboiler=86.0%=0.860\eta_{\text{boiler}} = 86.0\% = 0.860. Therefore, the thermal power transferred into the steam (Q˙in\dot{Q}_{\text{in}}) is:

Q˙in=ηboiler⋅Pin, fuel\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{in, fuel}}

Q˙in=0.860⋅1820 MW=1565.2 MW=1.5652×109 W\dot{Q}_{\text{in}} = 0.860 \cdot 1820\text{ MW} = 1565.2\text{ MW} = 1.5652 \times 10^9\text{ W}


03

Compute the Thermal Cycle Efficiency (ηcycle\eta_{\text{cycle}})

The thermal cycle efficiency represents the ratio of useful electrical power output (PelecP_{\text{elec}}) to the thermal power absorbed by the working steam (Q˙in\dot{Q}_{\text{in}}):

ηcycle=PelecQ˙in\eta_{\text{cycle}} = \frac{P_{\text{elec}}}{\dot{Q}_{\text{in}}}

Substitute the values:

ηcycle=635 MW1565.2 MW≈0.4057=40.6%\eta_{\text{cycle}} = \frac{635\text{ MW}}{1565.2\text{ MW}} \approx 0.4057 = 40.6\%

Common Pitfall: Do not confuse the thermal cycle efficiency (ηcycle=Pelec/Q˙in\eta_{\text{cycle}} = P_{\text{elec}} / \dot{Q}_{\text{in}}) with the plant's overall efficiency (ηoverall=Pelec/Pin, fuel=ηboiler⋅ηcycle≈34.9%\eta_{\text{overall}} = P_{\text{elec}} / P_{\text{in, fuel}} = \eta_{\text{boiler}} \cdot \eta_{\text{cycle}} \approx 34.9\%). The question specifically asks for the cycle efficiency relative to the heat absorbed by the steam.


04

Identify the Rejected Heat and Thermodynamic Sink

By the conservation of energy (First Law of Thermodynamics), the rate of energy that cannot be converted to mechanical/electrical work across the turbine stages is:

Q˙rejected=Q˙in−Pelec=1565.2 MW−635 MW=930.2 MW≈9.30×108 W\dot{Q}_{\text{rejected}} = \dot{Q}_{\text{in}} - P_{\text{elec}} = 1565.2\text{ MW} - 635\text{ MW} = 930.2\text{ MW} \approx 9.30 \times 10^8\text{ W}

According to the Second Law of Thermodynamics (Kelvin–Planck statement), a heat engine operating in a continuous cycle cannot convert all absorbed heat into work; it must reject heat to a lower-temperature reservoir. Here, this remaining 9.30×108 W9.30 \times 10^8\text{ W} of low-grade thermal internal energy is rejected via the condenser into the surrounding environment (such as cooling water and cooling towers).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the thermal cycle efficiency with the plant's overall fuel-to-electricity efficiency by dividing electrical power by total combustion power instead of heat absorbed by steam.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pcomb=65.0 kg/s×2.80×107 J/kg=1820 MWP_{\text{comb}} = 65.0\text{ kg/s} \times 2.80 \times 10^7\text{ J/kg} = 1820\text{ MW}

  2. Step 2

    ηcycle=PelecPcomb=635 MW1820 MW=0.3489=34.9%\eta_{\text{cycle}} = \frac{P_{\text{elec}}}{P_{\text{comb}}} = \frac{635\text{ MW}}{1820\text{ MW}} = 0.3489 = 34.9\%

    Correct

    Q˙in=ηboiler⋅Pin, fuel=0.860×1820 MW=1565.2 MW  ⟹  ηcycle=PelecQ˙in=635 MW1565.2 MW≈40.6%\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{in, fuel}} = 0.860 \times 1820\text{ MW} = 1565.2\text{ MW} \implies \eta_{\text{cycle}} = \frac{P_{\text{elec}}}{\dot{Q}_{\text{in}}} = \frac{635\text{ MW}}{1565.2\text{ MW}} \approx 40.6\%

    You divided the electrical power by the total combustion power instead of the thermal power absorbed by the steam. The thermodynamic cycle efficiency refers specifically to the working fluid's heat-to-work conversion stage.

  3. Step 3

    Waste heat is rejected to the condenser and cooling water.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the total combustion thermal power released by the burning coal.

You accurately identified the condenser and cooling water as the low-temperature thermodynamic heat sink.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Subsystem vs. Overall Efficiency Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defined cycle efficiency using the total chemical energy input rather than the thermal power actually transferred into the working steam cycle. The overall plant efficiency is the product of boiler efficiency and cycle efficiency (ηoverall=ηboiler⋅ηcycle\eta_{\text{overall}} = \eta_{\text{boiler}} \cdot \eta_{\text{cycle}}), whereas the thermal cycle efficiency evaluates only the turbine-generator thermodynamic loop (ηcycle=Pelec/Q˙in\eta_{\text{cycle}} = P_{\text{elec}} / \dot{Q}_{\text{in}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Energy Boundaries
  • In a multi-stage power plant, ηstage=Energy Out of StageEnergy In to Stage\eta_{\text{stage}} = \frac{\text{Energy Out of Stage}}{\text{Energy In to Stage}}, whereas ηoverall=Net Useful WorkTotal Primary Fuel Energy\eta_{\text{overall}} = \frac{\text{Net Useful Work}}{\text{Total Primary Fuel Energy}}.

  • Check whether the requested efficiency applies across the entire plant boundary or across an internal boundary such as the Rankine steam cycle.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the heat absorbed by the steam: Q˙in=ηboiler⋅Pcomb=0.860×1820 MW=1565.2 MW\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{comb}} = 0.860 \times 1820\text{ MW} = 1565.2\text{ MW}.

  2. Calculate the thermal cycle efficiency: ηcycle=PelecQ˙in=635 MW1565.2 MW≈0.4057=40.6%\eta_{\text{cycle}} = \frac{P_{\text{elec}}}{\dot{Q}_{\text{in}}} = \frac{635\text{ MW}}{1565.2\text{ MW}} \approx 0.4057 = 40.6\%.

Final answer

ηcycle=40.6%\eta_{\text{cycle}} = 40.6\%; remaining heat is rejected to the condenser and cooling water.

NEXT STEPS
Final Takeaways from Your Teacher
  • Multiply the fuel combustion rate by boiler efficiency first to obtain the thermal power delivered into the working fluid.

  • Use the ratio of electrical output to steam heat input whenever solving for thermal cycle efficiency.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the boiler efficiency by dividing rather than multiplying combustion power, leading to an artificially inflated input heat and underestimated cycle efficiency.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pcomb=65.0 kg/s×2.80×107 J/kg=1820 MWP_{\text{comb}} = 65.0\text{ kg/s} \times 2.80 \times 10^7\text{ J/kg} = 1820\text{ MW}

  2. Step 2

    Pth=Pcomb0.860=2116.3 MWP_{\text{th}} = \frac{P_{\text{comb}}}{0.860} = 2116.3\text{ MW}

    Correct

    Q˙in=ηboiler⋅Pcomb=0.860×1820 MW=1565.2 MW\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{comb}} = 0.860 \times 1820\text{ MW} = 1565.2\text{ MW}

    You divided the combustion power by the boiler efficiency rather than multiplying by it. Because an energy conversion stage cannot output more energy than enters it, the thermal energy transferred to steam must be less than the chemical input: Q˙in=ηboiler⋅Pcomb\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{comb}}.

  3. Step 3

    ηcycle=635 MW2116.3 MW=0.300=30.0%\eta_{\text{cycle}} = \frac{635\text{ MW}}{2116.3\text{ MW}} = 0.300 = 30.0\%

    Correct

    ηcycle=PelecQ˙in=635 MW1565.2 MW≈0.4057=40.6%\eta_{\text{cycle}} = \frac{P_{\text{elec}}}{\dot{Q}_{\text{in}}} = \frac{635\text{ MW}}{1565.2\text{ MW}} \approx 0.4057 = 40.6\%

    You correctly used the definition of cycle efficiency as useful electrical power divided by heat absorbed by steam, but your numerical answer was affected by the incorrect value of thermal power from Step 2.

  4. Step 4

    The remaining energy is rejected to the environment via cooling towers.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the combustion power released by the burning coal.

You correctly set up the efficiency formula as electrical power output divided by steam thermal power.

You correctly identified that the rejected thermal energy enters the environment via cooling towers.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted efficiency operation

You divided the fuel combustion power by the boiler efficiency instead of multiplying by it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing forward energy transfer (finding output from a known input, where Pout=η⋅PinP_{\text{out}} = \eta \cdot P_{\text{in}}) with backward sizing (finding required input from a desired output, where Pin=Pout/ηP_{\text{in}} = P_{\text{out}} / \eta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity check on energy flow
  • For any passive component or boiler, Pout≤PinP_{\text{out}} \le P_{\text{in}} because η≤1\eta \le 1.

  • Always verify that the output of an energy-conversion stage is smaller than the input entering that stage.

Forward vs. backward efficiency
  • Downstream output is Pout=η⋅PinP_{\text{out}} = \eta \cdot P_{\text{in}}; required upstream input is Pin=Pout/ηP_{\text{in}} = P_{\text{out}} / \eta.

  • Ask whether you are moving downstream along the energy chain (multiply) or upstream toward the primary source (divide).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate steam heat rate: Q˙in=ηboiler⋅Pcomb=0.860×1820 MW=1565.2 MW\dot{Q}_{\text{in}} = \eta_{\text{boiler}} \cdot P_{\text{comb}} = 0.860 \times 1820\text{ MW} = 1565.2\text{ MW}.

  2. Compute cycle efficiency: ηcycle=PelecQ˙in=635 MW1565.2 MW≈0.4057=40.6%\eta_{\text{cycle}} = \frac{P_{\text{elec}}}{\dot{Q}_{\text{in}}} = \frac{635\text{ MW}}{1565.2\text{ MW}} \approx 0.4057 = 40.6\%.

  3. Compute rejected heat: Q˙rejected=1565.2 MW−635 MW=930.2 MW≈9.30×108 W\dot{Q}_{\text{rejected}} = 1565.2\text{ MW} - 635\text{ MW} = 930.2\text{ MW} \approx 9.30 \times 10^8\text{ W}.

Final answer

ηcycle=40.6%\eta_{\text{cycle}} = 40.6\%; rejected to the environment via cooling towers.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the direction of energy flow before choosing multiplication or division by an efficiency value.

  • Practice checking whether calculated stage outputs exceed known stage inputs to catch accidental inversions immediately.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly identifies the electrical generator or turbine rather than the condenser and environment as the thermodynamic sink for rejected energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pcomb=65.0 kg/s×2.80×107 J/kg=1820 MWP_{\text{comb}} = 65.0\text{ kg/s} \times 2.80 \times 10^7\text{ J/kg} = 1820\text{ MW}

  2. Step 2

    Pth=0.860×1820 MW=1565.2 MWP_{\text{th}} = 0.860 \times 1820\text{ MW} = 1565.2\text{ MW}

  3. Step 3

    ηcycle=635 MW1565.2 MW=0.406=40.6%\eta_{\text{cycle}} = \frac{635\text{ MW}}{1565.2\text{ MW}} = 0.406 = 40.6\%

  4. Step 4

    The remaining is rejected into the electrical generator.

    Correct

    The remaining thermal energy (≈930.2 MW\approx 930.2\text{ MW}) is rejected to the ambient environment (cooling water / cooling towers via the steam condenser).

    The electrical generator is a device that converts mechanical work into useful electrical power, not a low-temperature heat reservoir. In a Rankine cycle, unconverted thermal energy in the expanded steam must be rejected to an external low-temperature sink (the environment) through the condenser.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately converted fuel mass rate and heating value into total thermal input power.

You accounted for the boiler efficiency to determine the exact enthalpy rate supplied to the steam cycle.

You correctly computed the thermal cycle efficiency using the net electrical work output.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misidentifying energy conversion components as thermodynamic heat sinks

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the mechanical-to-electrical energy conversion component (the generator) with the low-temperature thermodynamic reservoir (the condenser/environment) required by the Second Law of Thermodynamics to absorb waste heat.

REASONING PATH
Your ACEpath teacher’s suggested approach
Heat Engine Reservoirs vs. Working Machinery
  • By the Kelvin–Planck statement of the Second Law of Thermodynamics, a cyclical heat engine absorbs heat from a high-temperature source, converts part of it to work, and must reject residual heat to an external low-temperature thermal sink.

  • Always trace where unconverted heat physically flows: after turning the turbine, the low-pressure steam enters the condenser, transferring its latent heat to environmental cooling water or cooling towers.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the unconverted waste heat rate: Q˙out=Q˙in−Pelec=1565.2 MW−635 MW=930.2 MW\dot{Q}_{\text{out}} = \dot{Q}_{\text{in}} - P_{\text{elec}} = 1565.2\text{ MW} - 635\text{ MW} = 930.2\text{ MW}.

  2. Identify the physical stage after the turbine: the expanded steam flows into a surface condenser.

  3. Conclude the thermodynamic sink: the waste heat is rejected through the condenser to the surrounding environment (cooling water or cooling towers).

Final answer

ηcycle=40.6%\eta_{\text{cycle}} = 40.6\%; the remaining thermal energy (9.30×108 W9.30 \times 10^8\text{ W}) is rejected to the environment via the condenser and cooling water/cooling towers.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the schematic flow of a standard Rankine cycle, focusing on the four main components: boiler, turbine, condenser, and pump.

  • Practice identifying the distinction between work outputs (shaft work, electrical energy) and heat transfers (QHQ_H from combustion, QCQ_C to the environment).

Lock it in

Similar question

01

A natural gas combined-cycle plant burns fuel delivering 1200 MW1200\text{ MW} of chemical heat rate. The combustion chamber/HRSG transfers heat to the steam and gas working fluids with 90.0%90.0\% thermal transfer efficiency. If the generators produce 621 MW621\text{ MW} of electricity, find the thermal cycle efficiency ηcycle\eta_{\text{cycle}}.

Answer

ηcycle=57.5%\eta_{\text{cycle}} = 57.5\%. Heat absorbed by the working fluid is Q˙in=0.900×1200 MW=1080 MW\dot{Q}_{\text{in}} = 0.900 \times 1200\text{ MW} = 1080\text{ MW}. Then ηcycle=621 MW1080 MW=0.575\eta_{\text{cycle}} = \frac{621\text{ MW}}{1080\text{ MW}} = 0.575.

02

A biomass boiler burns fuel releasing 450 MW450\text{ MW} of thermal power. The plant's overall efficiency is 28.0%28.0\%. If the boiler efficiency is 80.0%80.0\%, determine: (a) the net electrical power output PelecP_{\text{elec}}, and (b) the thermal cycle efficiency ηcycle\eta_{\text{cycle}}.

Answer

(a) Pelec=126 MWP_{\text{elec}} = 126\text{ MW}; (b) ηcycle=35.0%\eta_{\text{cycle}} = 35.0\%. For (a), Pelec=0.280×450 MW=126 MWP_{\text{elec}} = 0.280 \times 450\text{ MW} = 126\text{ MW}. For (b), steam heat is Q˙in=0.800×450 MW=360 MW\dot{Q}_{\text{in}} = 0.800 \times 450\text{ MW} = 360\text{ MW}, giving ηcycle=126 MW360 MW=0.350\eta_{\text{cycle}} = \frac{126\text{ MW}}{360\text{ MW}} = 0.350 (or ηcycle=ηoverallηboiler=0.280.80=0.35\eta_{\text{cycle}} = \frac{\eta_{\text{overall}}}{\eta_{\text{boiler}}} = \frac{0.28}{0.80} = 0.35).

03

A nuclear thermal reactor delivers 3200 MW3200\text{ MW} of fission heat into primary coolant with a transfer efficiency of 98.0%98.0\% into the steam generators. The turbine cycle operates with ηcycle=33.5%\eta_{\text{cycle}} = 33.5\%. Find: (1) net electrical power generated, and (2) the rate of waste heat rejected to the ocean cooling loop.

Answer

(1) Pelec=1050.56 MW≈1051 MWP_{\text{elec}} = 1050.56\text{ MW} \approx 1051\text{ MW}; (2) Q˙rejected=2085.44 MW≈2085 MW\dot{Q}_{\text{rejected}} = 2085.44\text{ MW} \approx 2085\text{ MW}. Heat into steam is Q˙in=0.980×3200 MW=3136 MW\dot{Q}_{\text{in}} = 0.980 \times 3200\text{ MW} = 3136\text{ MW}. Electrical power is Pelec=0.335×3136 MW=1050.56 MWP_{\text{elec}} = 0.335 \times 3136\text{ MW} = 1050.56\text{ MW}. By conservation of energy, Q˙rejected=3136 MW−1050.56 MW=2085.44 MW\dot{Q}_{\text{rejected}} = 3136\text{ MW} - 1050.56\text{ MW} = 2085.44\text{ MW}.

Loading workspace…