Resources
A biomedical micro-sensor records an acoustic wave inside a microfluidic channel where the pressure amplitude is measured as . The liquid medium is pure water with a bulk density of and an acoustic propagation speed of . (a) Convert the pressure amplitude to Pascals () and the liquid density to standard SI units (). (b) Calculate the acoustic intensity of the wave in . (c) Determine the equivalent sound intensity level in decibels relative to the underwater reference standard of (corresponding to ).
Answer and steps
Final answer
(a) , ; (b) ; (c) (re ).
Steps
Part (a): Unit Conversions to Standard SI Units
- Pressure Amplitude (): The standard unit of pressure in SI is the Pascal ( or ). Since :
- Bulk Density (): The standard unit of density in SI is kilograms per cubic meter (). Converting from :
Part (b): Acoustic Intensity ()
The time-averaged acoustic intensity of a traveling sound wave is related to its pressure amplitude , the fluid density , and the acoustic wave speed by the formula:
Pitfall to avoid: Do not forget the factor of in the denominator. The factor of arises because is the peak (maximum) pressure amplitude rather than the root-mean-square pressure (, where ).
Substitute the values into the formula:
Part (c): Sound Intensity Level ()
Sound intensity level in decibels () compares an intensity to a standard reference intensity on a logarithmic scale:
Given the underwater acoustic reference intensity :
Compute the base-10 logarithm and multiply by :
The sound intensity level inside the channel is (re ).
Typical errors
01 The student omits the factor of 2 in the denominator of the intensity formula for pressure amplitude, confusing peak amplitude with RMS pressure.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the factor of in the denominator. Because is the peak (maximum) pressure amplitude of the wave, the time-averaged intensity requires dividing by (or writing ).
- Step 3Correct
Your decibel evaluation followed the correct logarithmic structure, but your numerical answer was shifted upward by due to the intensity error in part (b).
WHAT YOU DID WELL
Compliments from Your TeacherYou carried out the SI unit conversions for pressure amplitude and bulk density accurately.
You correctly structured the sound intensity level equation using base-10 logarithms.
You evaluated the arithmetic for the ratio and logarithm carefully without calculation slips.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used the instantaneous/RMS formula directly with the peak pressure amplitude , forgetting that time-averaging a sinusoidal wave introduces a factor of from .
REASONING PATH
Your ACEpath teacher’s suggested approach- Peak Amplitude vs. RMS Pressure
For a harmonic acoustic wave, the time-averaged intensity expressed in terms of peak pressure amplitude is . In terms of root-mean-square pressure, it is .
Always check whether the problem specifies peak pressure amplitude or RMS pressure before selecting the intensity formula.
- Decibel Impact of Amplitude Multipliers
A factor of error in intensity always changes the calculated sound level by .
Use this relationship as a quick sanity check to verify how intensity adjustments affect decibel levels.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the factor of in the denominator: .
Compute the time-averaged intensity: .
Substitute the corrected intensity into the decibel formula: .
(a) , ; (b) ; (c) (re )
02 The student uses the standard airborne reference intensity of 1.00 × 10⁻¹² W/m² instead of the specified underwater reference intensity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You substituted the standard airborne hearing threshold into the decibel formula instead of the underwater reference standard given in the prompt.
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately converted bar to Pascals and to .
You selected the correct formula and accounted for the factor of for peak amplitude.
You correctly set up the logarithmic definition of the sound intensity level in decibels.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou recalled the familiar reference intensity for air () out of habit instead of reading the problem's explicit underwater standard ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisDecibel levels always represent a ratio against a baseline reference value. Because acoustic impedance differs dramatically between media (e.g., water versus air), acoustics defines distinct reference levels: air uses (), whereas underwater acoustics standardizes to ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Medium and Reference Standard
Sound levels in decibels are relative: . Always check whether the medium is air () or water ().
Scan the problem statement for a custom or medium-specific reference value before entering a default constant.
- Compute Logarithmic Ratios Carefully
When dividing by tiny scientific notation denominators like , simplify powers of ten first: .
Separate the mantissa and exponent to verify your decibel magnitude makes physical sense for the designated medium.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the given underwater reference intensity: .
Form the intensity ratio using your calculated value : .
Apply the decibel definition: .
03 The student forgets to square the pressure amplitude in the acoustic intensity formula.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
⟹
- Step 2Correct
Acoustic wave intensity depends on the square of the pressure amplitude: . You omitted the exponent on , which gave an intensity several orders of magnitude too low.
- Step 3Correct
Your decibel formula and calculation were executed properly, but the result was altered because you substituted the incorrect intensity from part (b).
WHAT YOU DID WELL
Compliments from Your TeacherYou converted both given values into standard SI units correctly.
You remembered the factor of in the denominator of the intensity expression for peak pressure amplitude.
You correctly applied the base-10 logarithmic decibel formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote to the first power in the numerator of the intensity formula rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing wave intensity's quadratic dependence on amplitude with a linear dependence, or misrecalling the acoustic plane wave relation . In any wave, energy transport and intensity are proportional to the square of the amplitude.
REASONING PATH
Your ACEpath teacher’s suggested approach- Energy-Amplitude Quadratic Rule
Wave intensity is always proportional to amplitude squared: . For sound pressure waves, .
Always verify dimensional consistency: , whereas has units of velocity ().
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the squared pressure amplitude in the acoustic intensity formula: .
Substitute this intensity into the underwater decibel formula: .
(a) , ; (b) ; (c) (re )
Lock it in
What is the formula for the time-averaged acoustic intensity of a sound wave in terms of its peak pressure amplitude , density , and speed ?
. The factor of comes from averaging over a full cycle: .
Similar question
A planar ultrasound transducer generates a harmonic acoustic wave in tissue (density , sound speed ) with a peak pressure amplitude of . Calculate the time-averaged acoustic intensity of the ultrasound beam.
Answer
. Key steps: Identify as peak pressure; use .
An underwater hydrophone records a sinusoidal acoustic wave with peak pressure amplitude in seawater (, ). Determine the sound intensity level in decibels relative to the underwater reference .
Answer
(re ). Key steps: Compute intensity . Compute decibel level: .
In air (, ), a technician measures a sound wave to have an intensity of . (a) Determine the peak pressure amplitude . (b) What would the calculated peak amplitude be if an engineer mistakenly applied the formula without the factor of ?
Answer
(a) ; (b) Mistaken value: . Key steps: (a) Correctly rearrange . (b) Without the factor of , , underestimating the peak amplitude by a factor of .