Resources
A lead bullet of mass at an initial temperature of is fired horizontally at a speed of into a large, stationary block of ice at and comes completely to rest inside it. Assuming of the bullet's initial kinetic energy, along with all of the thermal energy released as the bullet cools from to , is absorbed directly by the surrounding ice to cause melting, calculate the total mass of ice melted. Use and .
Answer and steps
Final answer
Steps
Identify the sources of energy transferred to the ice
To determine the total mass of ice melted, we calculate the total energy transferred to the ice to cause melting and apply the latent heat of fusion.
The total energy absorbed by the ice, , comes from two sources:
- A fraction () of the bullet's initial kinetic energy ().
- The thermal energy released () as the bullet cools from its initial temperature () to thermal equilibrium with the ice at .
Calculate the kinetic energy absorbed by the ice
The initial kinetic energy of the lead bullet is:
Substituting the given values:
The portion of this kinetic energy transferred to the ice is:
Calculate the thermal energy released by the cooling bullet
As the lead bullet cools down to , the heat released is:
Calculate the total energy absorbed and the mass of ice melted
The total heat absorbed by the ice is:
Since the ice is already at its melting point (), all of this heat contributes directly to phase change without changing the temperature:
Solving for the mass of melted ice :
Common Pitfall: Be careful not to assume that of the kinetic energy converts into melting ice; only is absorbed by the ice. Additionally, ensure the bullet's mass is consistently expressed in kilograms rather than grams.
Typical errors
01 The student forgets to apply the 85.0% efficiency factor to the kinetic energy, assuming all initial kinetic energy is absorbed to melt ice.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The problem states that only of the bullet's kinetic energy is transferred to the ice. You added of () rather than multiplying it by ().
- Step 4Correct
Your phase-change formula setup was mathematically sound, but the numerical result was affected by the unscaled kinetic energy term from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used to find the initial kinetic energy of the bullet.
You correctly applied to find the thermal energy released as the bullet cooled to .
You correctly related the melting mass to latent heat using .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou calculated total energy as instead of , missing the factor .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated all initial mechanical energy as converting directly into heat absorbed by the target without checking the problem statement for an energy partition or efficiency percentage.
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for energy partition factors
When an inelastic collision or braking process states that only a fraction of mechanical energy enters a thermal reservoir, write , not .
Always circle percentage or fractional efficiency values in the prompt and write them directly next to the corresponding energy term before summing.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the kinetic energy absorbed by the ice: .
Add the cooling thermal energy to find the total heat absorbed: .
Calculate the melted ice mass: .
02 The student considers only the kinetic energy transferred to the ice and omits the thermal energy released by the cooling bullet.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You accounted for the of kinetic energy, but you omitted the heat released by the bullet as it cooled from to ().
- Step 3Correct
Because was missing the cooling term, your calculated mass of melted ice was slightly too small.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the initial kinetic energy of the bullet.
You correctly applied the conversion factor to find the kinetic energy transferred as heat.
You correctly related the heat absorbed by melting ice to latent heat via .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou focused exclusively on the mechanical energy converted during impact and overlooked that the bullet enters at and must reach thermal equilibrium at , releasing sensible heat () into the ice.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify all energy contributions
In an inelastic thermal stopping problem, total heat transferred equals converted mechanical energy plus sensible heat lost: .
Always audit whether moving objects have an initial temperature different from the target medium.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the heat released by the cooling bullet: .
Sum the two energy contributions: .
Divide by the latent heat of fusion: .
03 The student forgets to square the velocity when calculating the initial kinetic energy of the bullet.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You multiplied by instead of . Kinetic energy depends on the square of the velocity.
- Step 2Correct
Your method of taking of the bullet's kinetic energy is correct, but the numerical result is affected by the incorrect value of from step (a).
- Step 3
- Step 4Correct
You correctly summed the two energy contributions, but this total inherits the earlier error from .
- Step 5Correct
You applied the latent heat equation properly, but the resulting mass of ice melted is incorrect due to the propagated energy value.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the sensible heat released as the lead bullet cools to .
You correctly identified that the total heat melting the ice is the sum of the absorbed kinetic energy and the bullet's thermal energy.
You properly applied the latent heat of fusion relation .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou omitted the exponent when writing the kinetic energy formula, calculating instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisA mechanical formula recall slip occurred during step (a), where velocity was entered as a linear factor rather than being squared in the kinetic energy expression.
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinetic Energy Formula
Always verify units and exponents for mechanical energy before performing arithmetic; the unit requires squaring speed.
- Latent Heat Equation
Ensure that the total absorbed thermal energy accounts for both the mechanical dissipation and temperature cooling.
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
In an inelastic collision where a fraction of kinetic energy is converted into heat absorbed by a target, how is the absorbed thermal energy expressed?
. Never assume unless explicitly stated that all mechanical energy is absorbed by that specific object.
Similar question
A copper slug at is shot at into a large ice block at and stops. If of its initial kinetic energy is absorbed by the ice to melt it, how much ice melts? (Use )
Answer
. Key steps: . Energy absorbed by ice: . Melted mass: .
A silver pellet at is dropped into ice at at a low speed so that its kinetic energy is negligible. If all thermal energy released as it cools to melts ice, calculate the mass of ice melted. Use and .
Answer
. Key steps: . Melted mass: .
A iron bullet at enters an ice block at at and comes to rest. Exactly of the bullet's kinetic energy and of its sensible heat loss as it cools to melt the ice. Find the total mass of ice melted. (Use and )
Answer
. Key steps: . Kinetic energy absorbed: . Cooling heat: . Total heat: . Melted mass: .