Resources
A sample of brass with a specific heat capacity of and mass is heated to . It is then submerged into an insulated container containing of water () initially at . Heat loss to the container walls is negligible. Rather than finding the final equilibrium temperature directly, determine the ratio of the thermal energy absorbed by the water to the initial internal thermal energy difference of the brass relative to the water's initial temperature: , and report the final equilibrium temperature and the value of .
Answer and steps
Final answer
, (or )
Steps
Calculate the heat capacities of the brass and water
The heat capacity of each substance is the product of its mass and its specific heat capacity :
- For the brass sample:
- For the water:
Set up the thermal equilibrium equation to find
Since heat loss to the surroundings and container is negligible, the heat gained by the water must equal the heat lost by the brass:
Substitute the known values:
Expand and group like terms:
Determine the ratio
The maximum possible thermal energy the brass could transfer if cooled all the way to the water's initial temperature is:
Because , the fraction can be evaluated either through energy or directly via temperature changes:
Substitute the values:
(Note: Alternatively, using heat capacities directly, .)
Typical errors
01 The student sets both temperature changes as (T_f - T_i), incorrectly writing heat lost by brass as (T_f - 100.0) without a negative sign, leading to an impossible negative final temperature and negative ratio.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set , but expressed heat lost as . Because brass cools down, is negative. For to be positive, you must write , or alternatively write the conservation law as with all temperature changes defined as .
- Step 2Correct
Your algebra followed consistently from your initial equation, but the sign error from Step 1 caused the final temperature to evaluate to , which is physically impossible since it lies below the initial temperature of the cold water ().
- Step 3
,
Correct,
You correctly formulated , but substituting the erroneous temperature into produced a negative heat absorbed by the water.
- Step 4Correct
You correctly took the ratio , but the negative propagated from earlier steps led to a negative efficiency ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and computed the heat capacities and .
You correctly defined and computed its numerical value accurately as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of on the heat-lost side of the equation .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the two standard ways to express conservation of thermal energy: either equate magnitude magnitudes as (where both sides must be positive: ), or sum all signed heats to zero as .
REASONING PATH
Your ACEpath teacher’s suggested approach- Sanity check the equilibrium temperature range
For two substances exchanging heat without a phase change or external work, the final equilibrium temperature must lie strictly between the initial temperatures: .
Whenever you compute , immediately check if . Finding is an immediate sign of an algebraic or sign error.
- Pick one consistent heat equation convention
If using , write both temperature differences as positive quantities: .
Ensure the higher temperature comes first on each side of the equation when equating positive heat flows.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the heat balance with positive temperature differences: .
Substitute known values: .
Expand and group terms: .
Solve for equilibrium temperature: .
Compute .
, (or )
02 The student forgets to account for specific heat capacities and simply averages the temperatures weighted only by mass, yielding an incorrect final temperature and ratio.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You treated heat exchange as equating mass times temperature change (). Heat gained or lost is given by , so you must multiply each substance's mass by its specific heat capacity ( and ).
- Step 2Correct
Your simplified ratio was algebraically valid since cancels out, but substituting your incorrect value of led directly to an incorrect numerical ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou recognized that heat gained by the cold water equals heat lost by the hot brass in an insulated system.
You correctly simplified the thermal ratio into an equivalent temperature-difference ratio.
You performed the linear algebraic manipulations and arithmetic without calculation slips.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated temperature equilibration as a mass-weighted average of temperatures, forgetting that different materials require different amounts of thermal energy per kilogram per degree change ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Heat Transfer Definition
Always multiply the mass of each substance by its specific heat capacity before equating and .
- Thermal Inertia Check
Water has a much higher specific heat capacity than metals ( vs. ).
Check whether your final temperature is much closer to the substance with the dominant heat capacity (), which is water in this problem.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the specific heat capacities: .
Substitute the given constants: .
Solve for the final temperature: .
Calculate the ratio : .
, (or )
03 The student computes the ratio using the temperature difference relative to the brass initial temperature in the denominator instead of the water initial temperature, dividing by (T_b,i - T_f) rather than (T_b,i - T_w,i).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You replaced in the denominator with . The denominator represents the maximum possible heat transfer if the brass were cooled all the way to the water's initial temperature (), not the actual heat lost to reach .
WHAT YOU DID WELL
Compliments from Your TeacherYou applied the principle of conservation of energy to equate heat gained and heat lost.
You accurately solved the linear equation for the equilibrium temperature .
You correctly calculated the heat absorbed by the water.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally wrote in the denominator of instead of the specified .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the actual heat released by the hotter object, , with the theoretical maximum available thermal energy relative to the cold reservoir, . Since , dividing by the actual heat lost trivially yields .
REASONING PATH
Your ACEpath teacher’s suggested approach- Reference Temperature in Denominator
The ratio compares actual transferred heat to the maximum thermal energy difference relative to the colder initial temperature: .
Always verify whether the temperature difference in a ratio or efficiency formula is measured relative to or an initial baseline temperature.
- Sanity Check for Heat Exchange Ratios
Because the hot object stops transferring heat once it reaches , the actual heat transferred must be strictly less than .
Check that ; obtaining indicates that the numerator and denominator represent the exact same heat quantity.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the maximum possible heat release: .
Divide the absorbed heat by : .
, (or )
Lock it in
When setting up heat exchange using , how must the temperature differences be written on each side?
Both sides must be positive: write for the substance that gains heat, and for the substance that loses heat.
Similar question
A block of aluminum () at is placed into of water () at . Assuming no heat loss to the surroundings, find the final equilibrium temperature .
Answer
. Heat balance: .
An unknown metal sample of mass heated to is submerged in of water at in an insulated cup. The system reaches equilibrium at . Determine the specific heat capacity of the metal.
Answer
. Energy conservation: .
A copper block () at is dropped into an insulated container holding of water at . Compute the equilibrium temperature and the thermal energy fraction absorbed by the water: .
Answer
, (or ). Heat capacities: , . Equilibrium: . Then (alternatively, ).