Resources

A piston in an internal combustion engine oscillates along a linear track according to x(t)=Acos⁡(ωt+ϕ0)x(t) = A\cos(\omega t + \phi_0) with an amplitude of A=0.0750 mA = 0.0750\text{ m} and a frequency of f=50.0 Hzf = 50.0\text{ Hz}. To prevent structural wear, the absolute value of the piston's acceleration must not exceed a safety threshold of amax=7.50×103 m/s2a_{\text{max}} = 7.50 \times 10^3\text{ m/s}^2. (a) Calculate the maximum acceleration magnitude experienced by the piston under these operating parameters, and (b) determine whether this operating state remains strictly within the manufacturer's critical acceleration limit.

Answer and steps

Final answer

(a) amax, actual=7.40×103 m/s2a_{\text{max, actual}} = 7.40 \times 10^3\text{ m/s}^2; (b) Yes, it remains strictly within the threshold because 7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2.

Steps

Part (a): Calculating the Maximum Acceleration Magnitude

  1. Relate frequency to angular frequency
    The motion is described by simple harmonic motion (SHM): x(t)=Acos⁡(ωt+ϕ0)x(t) = A\cos(\omega t + \phi_0) The relationship between the cyclical frequency ff and the angular frequency ω\omega is: ω=2πf\omega = 2\pi f Substituting the given frequency f=50.0 Hzf = 50.0\text{ Hz}: ω=2π(50.0 s−1)=100π rad/s≈314.16 rad/s\omega = 2\pi (50.0\text{ s}^{-1}) = 100\pi\text{ rad/s} \approx 314.16\text{ rad/s}
  2. Determine the formula for acceleration
    Differentiating position x(t)x(t) twice with respect to time gives the acceleration: v(t)=dxdt=−Aωsin⁡(ωt+ϕ0)v(t) = \frac{dx}{dt} = -A\omega\sin(\omega t + \phi_0) a(t)=dvdt=−Aω2cos⁡(ωt+ϕ0)a(t) = \frac{dv}{dt} = -A\omega^2\cos(\omega t + \phi_0) Since the extreme values of the cosine function are ±1\pm 1, the maximum magnitude of the acceleration occurs at the turning points (x=±Ax = \pm A): amax, actual=ω2A=(2πf)2Aa_{\text{max, actual}} = \omega^2 A = (2\pi f)^2 A
  3. Compute the numerical value
    Substitute the given values into the equation: amax, actual=(100π rad/s)2⋅(0.0750 m)a_{\text{max, actual}} = (100\pi\text{ rad/s})^2 \cdot (0.0750\text{ m}) amax, actual=10 000π2⋅0.0750 m/s2=750π2 m/s2a_{\text{max, actual}} = 10\,000\pi^2 \cdot 0.0750\text{ m/s}^2 = 750\pi^2\text{ m/s}^2 Using π≈3.14159\pi \approx 3.14159: amax, actual≈750⋅9.8696 m/s2≈7402 m/s2a_{\text{max, actual}} \approx 750 \cdot 9.8696\text{ m/s}^2 \approx 7402\text{ m/s}^2 Expressed to three significant figures: amax, actual=7.40×103 m/s2a_{\text{max, actual}} = 7.40 \times 10^3\text{ m/s}^2

Part (b): Evaluating the Safety Threshold

Compare the calculated peak acceleration with the structural limit:

  • Actual maximum acceleration: amax, actual=7.40×103 m/s2a_{\text{max, actual}} = 7.40 \times 10^3\text{ m/s}^2
  • Critical safety threshold: alimit=7.50×103 m/s2a_{\text{limit}} = 7.50 \times 10^3\text{ m/s}^2

Because 7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2, the engine's operating state remains strictly within the manufacturer's critical acceleration limit.

Common Pitfall: A frequent mistake is using ff directly in place of ω\omega (writing amax=f2Aa_{\text{max}} = f^2 A instead of (2πf)2A(2\pi f)^2 A), which underestimates the acceleration by a factor of 4π2≈39.54\pi^2 \approx 39.5. Always convert linear frequency (in Hz\text{Hz}) to angular frequency (in rad/s\text{rad/s}).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misremembers the acceleration formula as ωA rather than ω²A, confusing maximum acceleration with maximum velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=2πf=2π(50.0)=314.16 rad/s\omega = 2\pi f = 2\pi(50.0) = 314.16\text{ rad/s}

  2. Step 2

    amax=ωA  ⟹  amax=(314.16)(0.0750)=23.6 m/s2a_{\text{max}} = \omega A \implies a_{\text{max}} = (314.16)(0.0750) = 23.6\text{ m/s}^2

    Correct

    amax=ω2A=(314.16 rad/s)2(0.0750 m)≈7.40×103 m/s2a_{\text{max}} = \omega^2 A = (314.16\text{ rad/s})^2(0.0750\text{ m}) \approx 7.40 \times 10^3\text{ m/s}^2

    You used the formula for maximum speed (vmax=ωAv_{\text{max}} = \omega A) rather than maximum acceleration (amax=ω2Aa_{\text{max}} = \omega^2 A). Each derivative with respect to time brings out another factor of ω\omega, giving units of m/s2\text{m/s}^2 only when ω\omega is squared.

  3. Step 3

    23.6 m/s2<7500 m/s223.6\text{ m/s}^2 < 7500\text{ m/s}^2, so it remains within the limit.

    Correct

    7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2, so it remains strictly within the limit.

    Your comparison logic is sound, but it evaluated the incorrect acceleration value obtained in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related cyclical frequency to angular frequency using ω=2πf\omega = 2\pi f.

You correctly identified the amplitude and frequency from the problem statement.

You compared your calculated peak value against the safety threshold to answer part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion between maximum velocity and maximum acceleration

You wrote amax=ωAa_{\text{max}} = \omega A instead of amax=ω2Aa_{\text{max}} = \omega^2 A, confusing peak speed with peak acceleration.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In simple harmonic motion x(t)=Acos⁡(ωt+ϕ0)x(t) = A\cos(\omega t + \phi_0), differentiating once gives velocity v(t)=−Aωsin⁡(ωt+ϕ0)v(t) = -A\omega\sin(\omega t + \phi_0) with peak amplitude vmax=ωAv_{\text{max}} = \omega A. Differentiating twice gives acceleration a(t)=−Aω2cos⁡(ωt+ϕ0)a(t) = -A\omega^2\cos(\omega t + \phi_0) with peak amplitude amax=ω2Aa_{\text{max}} = \omega^2 A. A quick dimensional check confirms that [","ωA]=(s−1)(m)=m/s[","\omega A] = (\text{s}^{-1})(\text{m}) = \text{m/s} (speed), while [ω2A]=(s−2)(m)=m/s2[\omega^2 A] = (\text{s}^{-2})(\text{m}) = \text{m/s}^2 (acceleration).

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis Check
  • Velocity has units of m/s\text{m/s}, whereas acceleration has units of m/s2\text{m/s}^2.

  • Check that each time derivative introduces a factor of ω\omega with units of s−1\text{s}^{-1}, so amaxa_{\text{max}} must scale as ω2A\omega^2 A.

SHM Extremum Derivatives
  • xmax=Ax_{\text{max}} = A, vmax=ωAv_{\text{max}} = \omega A, and amax=ω2Aa_{\text{max}} = \omega^2 A.

  • Recall that acceleration is proportional to displacement (a=−ω2xa = -\omega^2 x), meaning maximum magnitude occurs at the turning points where ∣x∣=A|x| = A.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate maximum acceleration magnitude: amax=ω2A=(100π rad/s)2(0.0750 m)=750π2 m/s2≈7.40×103 m/s2a_{\text{max}} = \omega^2 A = (100\pi\text{ rad/s})^2(0.0750\text{ m}) = 750\pi^2\text{ m/s}^2 \approx 7.40 \times 10^3\text{ m/s}^2.

  2. Compare with the critical threshold: 7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2.

Final answer

(a) amax=7.40×103 m/s2a_{\text{max}} = 7.40 \times 10^3\text{ m/s}^2; (b) Yes, the operating state remains strictly within the threshold.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice deriving v(t)v(t) and a(t)a(t) directly from x(t)=Acos⁡(ωt)x(t) = A\cos(\omega t) to reinforce where powers of ω\omega come from.

  • Perform a quick unit check on kinetic and dynamic formulas before plugging in numerical values.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert linear frequency f to angular frequency ω, using a_max = (2πf)²A without the factor of 2π (evaluating f²A instead of ω²A).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    amax=f2A  ⟹  amax=(50.0)2(0.0750)  ⟹  amax=187.5 m/s2a_{\text{max}} = f^2 A \implies a_{\text{max}} = (50.0)^2(0.0750) \implies a_{\text{max}} = 187.5\text{ m/s}^2

    Correct

    amax=ω2A=(2πf)2A=[2π(50.0)]2(0.0750)≈7.40×103 m/s2a_{\text{max}} = \omega^2 A = (2\pi f)^2 A = [2\pi(50.0)]^2(0.0750) \approx 7.40 \times 10^3\text{ m/s}^2

    In simple harmonic motion, the acceleration amplitude is given by amax=ω2Aa_{\text{max}} = \omega^2 A, where ω\omega is the angular frequency in radians per second. Because ω=2πf\omega = 2\pi f, the formula requires (2πf)2A(2\pi f)^2 A, not f2Af^2 A.

  2. Step 2

    187.5 m/s2<7500 m/s2187.5\text{ m/s}^2 < 7500\text{ m/s}^2, so it remains within the limit.

    Correct

    7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2, so the operating state remains strictly within the critical limit.

    Your comparison logic is sound and you reached the correct qualitative conclusion, but your comparison was based on the underestimated numerical value from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the maximum acceleration in simple harmonic motion is proportional to amplitude AA and the square of frequency.

You correctly set up the inequality comparison against the safety threshold of 7.50×103 m/s27.50 \times 10^3\text{ m/s}^2.

You executed the arithmetic calculation cleanly and included proper physical units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear vs. Angular Frequency Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You omitted the factor of 2π2\pi that converts cyclical frequency ff (in Hz\text{Hz}) to angular frequency ω\omega (in rad/s\text{rad/s}), which underestimated the peak acceleration by a factor of 4π2≈39.54\pi^2 \approx 39.5.

REASONING PATH
Your ACEpath teacher’s suggested approach
Angular Frequency Conversion
  • Whenever a kinematic or harmonic formula contains ω\omega, replace it with 2πf2\pi f or 2πT\frac{2\pi}{T}.

  • Check whether the given frequency has units of Hz\text{Hz} (cycles/s) or rad/s\text{rad/s} before squaring it in dynamic formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the cyclical frequency to angular frequency: ω=2πf=2π(50.0 s−1)=100π rad/s≈314.16 rad/s\omega = 2\pi f = 2\pi (50.0\text{ s}^{-1}) = 100\pi\text{ rad/s} \approx 314.16\text{ rad/s}.

  2. Substitute ω\omega and amplitude A=0.0750 mA = 0.0750\text{ m} into the peak acceleration formula: amax=ω2A=(100π rad/s)2(0.0750 m)=750π2 m/s2≈7402 m/s2a_{\text{max}} = \omega^2 A = (100\pi\text{ rad/s})^2 (0.0750\text{ m}) = 750\pi^2\text{ m/s}^2 \approx 7402\text{ m/s}^2.

  3. Express to three significant figures: amax=7.40×103 m/s2a_{\text{max}} = 7.40 \times 10^3\text{ m/s}^2.

  4. Compare with the structural limit: 7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2.

Final answer

(a) amax=7.40×103 m/s2a_{\text{max}} = 7.40 \times 10^3\text{ m/s}^2; (b) Yes, it remains strictly within the limit.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivatives of x(t)=Acos⁡(ωt+ϕ0)x(t) = A\cos(\omega t + \phi_0) to see why the chain rule brings out a factor of ω\omega with each time derivative.

  • Practice writing ω=2πf\omega = 2\pi f explicitly as your first line of working whenever simple harmonic motion parameters are given in hertz.

OverviewACEpath Teacher's Diagnosis

03 The student squares the frequency but omits squaring the factor of 2π when calculating ω², writing ω² = 2πf² instead of (2πf)².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    amax=2πf2A  ⟹  amax=2π(50.0)2(0.0750)a_{\text{max}} = 2\pi f^2 A \implies a_{\text{max}} = 2\pi(50.0)^2(0.0750)

    Correct

    amax=ω2A=(2πf)2A=4π2f2A  ⟹  amax=4π2(50.0)2(0.0750)a_{\text{max}} = \omega^2 A = (2\pi f)^2 A = 4\pi^2 f^2 A \implies a_{\text{max}} = 4\pi^2 (50.0)^2 (0.0750)

    You substituted ω=2πf\omega = 2\pi f into ω2A\omega^2 A, but only squared the frequency ff rather than the entire quantity (2πf)(2\pi f).

  2. Step 2

    amax=1.18×103 m/s2a_{\text{max}} = 1.18 \times 10^3\text{ m/s}^2

    Correct

    amax=7.40×103 m/s2a_{\text{max}} = 7.40 \times 10^3\text{ m/s}^2

    Because the factor of 2π2\pi was not squared in the formula, your calculated value is too small by a factor of 2π2\pi.

  3. Step 3

    1.18×103 m/s2<7.50×103 m/s2, so it remains within the limit.1.18 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2\text{, so it remains within the limit.}

    Correct

    7.40×103 m/s2<7.50×103 m/s2, so it remains within the limit.7.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2\text{, so it remains within the limit.}

    Your comparison logic is sound, but it relies on your incorrect numerical value from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the maximum acceleration in simple harmonic motion is proportional to frequency squared and amplitude.

You correctly substituted the numerical values for amplitude and frequency into your formula.

You compared your calculated peak acceleration to the manufacturer's limit with a clear inequality.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Parentheses When Squaring Angular Frequency

You squared the variable ff but forgot to square the coefficient 2π2\pi.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating ω2\omega^2 with 2πf22\pi f^2: when replacing the angular frequency ω=2πf\omega = 2\pi f, the entire product must be grouped inside parentheses before squaring, giving ω2=(2πf)2=4π2f2\omega^2 = (2\pi f)^2 = 4\pi^2 f^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Expanding Grouped Quantities
  • (α⋅β)2=α2β2(\alpha \cdot \beta)^2 = \alpha^2 \beta^2, never αβ2\alpha \beta^2.

  • Always write ω2=(2πf)2=4π2f2\omega^2 = (2\pi f)^2 = 4\pi^2 f^2 explicitly before substituting numerical values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct angular frequency: ω=2πf=2π(50.0 s−1)=100π rad/s\omega = 2\pi f = 2\pi(50.0\text{ s}^{-1}) = 100\pi\text{ rad/s}.

  2. Square the full angular frequency: ω2=(100π rad/s)2=10 000π2 rad2/s2\omega^2 = (100\pi\text{ rad/s})^2 = 10\,000\pi^2\text{ rad}^2/\text{s}^2.

  3. Multiply by the amplitude: amax=ω2A=10 000π2×0.0750 m=750π2 m/s2≈7.40×103 m/s2a_{\text{max}} = \omega^2 A = 10\,000\pi^2 \times 0.0750\text{ m} = 750\pi^2\text{ m/s}^2 \approx 7.40 \times 10^3\text{ m/s}^2.

  4. Compare with the threshold: 7.40×103 m/s2<7.50×103 m/s27.40 \times 10^3\text{ m/s}^2 < 7.50 \times 10^3\text{ m/s}^2.

Final answer

(a) amax=7.40×103 m/s2a_{\text{max}} = 7.40 \times 10^3\text{ m/s}^2; (b) Yes, it remains strictly within the threshold.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice writing (2πf)2=4π2f2(2\pi f)^2 = 4\pi^2 f^2 as an explicit intermediate step in formulas involving ω2\omega^2.

  • Check physical units: verify that ω=2πf\omega = 2\pi f is converted to rad/s\text{rad/s} first before evaluating higher powers.

Lock it in

Similar question

01

A mass on a spring oscillates with an amplitude of A=0.040 mA = 0.040\text{ m} and an angular frequency of ω=25 rad/s\omega = 25\text{ rad/s}. Calculate (a) the maximum speed vmaxv_{\text{max}} and (b) the maximum acceleration amaxa_{\text{max}}.

Answer

(a) vmax=ωA=(25)(0.040)=1.0 m/sv_{\text{max}} = \omega A = (25)(0.040) = 1.0\text{ m/s}; (b) amax=ω2A=(25)2(0.040)=25 m/s2a_{\text{max}} = \omega^2 A = (25)^2(0.040) = 25\text{ m/s}^2.

02

A speaker cone oscillates in simple harmonic motion at a frequency of f=120 Hzf = 120\text{ Hz} with a peak-to-peak displacement of 4.0 mm4.0\text{ mm}. Determine the maximum acceleration magnitude of the cone in terms of gg (take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer

A=2.0 mm=0.0020 mA = 2.0\text{ mm} = 0.0020\text{ m}. ω=2πf=240π rad/s\omega = 2\pi f = 240\pi\text{ rad/s}. amax=ω2A=(240π)2(0.0020)≈1137 m/s2a_{\text{max}} = \omega^2 A = (240\pi)^2(0.0020) \approx 1137\text{ m/s}^2. In terms of gg: amax/g≈1137/9.80≈116ga_{\text{max}}/g \approx 1137 / 9.80 \approx 116g (or 1.14×103 m/s21.14 \times 10^3\text{ m/s}^2).

03

A delicate sensor component undergoes linear vibration at f=80.0 Hzf = 80.0\text{ Hz}. The component is rated for a maximum acceleration of 5.00×103 m/s25.00 \times 10^3\text{ m/s}^2. What is the maximum allowable oscillation amplitude AallowA_{\text{allow}} that keeps the component safely within its acceleration limit?

Answer

ω=2π(80.0)=160π rad/s\omega = 2\pi(80.0) = 160\pi\text{ rad/s}. Since amax=ω2A≤5.00×103 m/s2a_{\text{max}} = \omega^2 A \le 5.00 \times 10^3\text{ m/s}^2, we have Aallow=alimitω2=5000(160π)2=500025600π2≈1.98×10−2 m=1.98 cmA_{\text{allow}} = \frac{a_{\text{limit}}}{\omega^2} = \frac{5000}{(160\pi)^2} = \frac{5000}{25600\pi^2} \approx 1.98 \times 10^{-2}\text{ m} = 1.98\text{ cm} (or 19.8 mm19.8\text{ mm}).

Loading workspace…