Resources

A laboratory heating mantle is designed to dissipate an electric power of P=350 WP = 350\ \text{W} when operating continuously, consuming a total electrical energy of E=1.26×106 JE = 1.26 \times 10^6\ \text{J} from a V=110 VV = 110\ \text{V} DC source. (a) Calculate the required operating duration Δt\Delta t of the heating mantle in minutes. (b) Calculate the internal electrical resistance RR of the heating mantle.

Answer and steps

Final answer

(a) Δt=60.0 min\Delta t = 60.0\ \text{min}; (b) R=34.6 ΩR = 34.6\ \Omega

Steps

Part (a): Determine the Operating Duration Δt\Delta t

  1. Relate electrical energy, power, and time: Electrical power PP is the rate at which electrical energy EE is transferred or dissipated over time Δt\Delta t: E=P⋅ΔtE = P \cdot \Delta t
  2. Solve for time in seconds: Rearrange the formula to express Δt\Delta t in terms of EE and PP: Δt=EP\Delta t = \frac{E}{P} Substitute the given values (E=1.26×106 JE = 1.26 \times 10^6\ \text{J} and P=350 WP = 350\ \text{W}): Δt=1.26×106 J350 W=3600 s\Delta t = \frac{1.26 \times 10^6\ \text{J}}{350\ \text{W}} = 3600\ \text{s}
  3. Convert time to minutes: Since 1 min=60 s1\ \text{min} = 60\ \text{s}: Δt=3600 s60 s/min=60.0 min\Delta t = \frac{3600\ \text{s}}{60\ \text{s/min}} = 60.0\ \text{min}

Common Pitfall: Standard energy units (Joules\text{Joules}) divided by power (Watts\text{Watts}) directly give time in seconds (s\text{s}). Be sure to perform the unit conversion to minutes as requested.


Part (b): Determine the Internal Electrical Resistance RR

  1. Relate electric power, potential difference, and resistance: The electrical power dissipated by an ohmic resistor connected to a voltage source VV is given by Joule's law: P=V2RP = \frac{V^2}{R}
  2. Solve for the resistance RR: Rearrange the formula to solve for RR: R=V2PR = \frac{V^2}{P}
  3. Substitute the known values: Using V=110 VV = 110\ \text{V} and P=350 WP = 350\ \text{W}: R=(110 V)2350 W=12100 V2350 W≈34.57 ΩR = \frac{(110\ \text{V})^2}{350\ \text{W}} = \frac{12100\ \text{V}^2}{350\ \text{W}} \approx 34.57\ \Omega

    Rounding to three significant figures gives: R=34.6 ΩR = 34.6\ \Omega

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the operating time in seconds using Δt = E / P but forgets to convert the result into minutes as requested.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δt=EP  ⟹  Δt=1.26×106350  ⟹  Δt=3600 s\Delta t = \frac{E}{P} \implies \Delta t = \frac{1.26 \times 10^6}{350} \implies \Delta t = 3600\text{ s}

    Correct

    Δt=EP=1.26×106 J350 W=3600 s=60.0 min\Delta t = \frac{E}{P} = \frac{1.26 \times 10^6\text{ J}}{350\text{ W}} = 3600\text{ s} = 60.0\text{ min}

    You correctly applied the relationship E=P⋅ΔtE = P \cdot \Delta t and accurately computed the time in seconds as 3600 s3600\text{ s}. However, this step is incomplete because the problem explicitly asked for the operating duration in minutes, requiring a final conversion by dividing by 60 s/min60\text{ s/min}.

  2. Step 2

    P=V2R  ⟹  R=V2P=1102350  ⟹  R=34.6 ΩP = \frac{V^2}{R} \implies R = \frac{V^2}{P} = \frac{110^2}{350} \implies R = 34.6\ \Omega

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the electrical energy formula E=P⋅ΔtE = P \cdot \Delta t to find operating time.

You correctly related electric power, voltage, and resistance using P=V2RP = \frac{V^2}{R} and solved for R=34.6 ΩR = 34.6\ \Omega.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Time Unit Conversion

You calculated the operating duration in standard SI units (3600 s3600\text{ s}), but missed the final unit conversion to minutes requested in the prompt.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Dividing energy in joules by power in watts yields time directly in seconds (1 W=1 J/s1\text{ W} = 1\text{ J/s}). When an SI calculation works out smoothly to a clean number, it is easy to stop before verifying whether the question specified a different unit such as minutes or hours.

REASONING PATH
Your ACEpath teacher’s suggested approach
Verify Target Units
  • SI formulas produce base units (seconds for time). Always check whether the prompt asks for a non-base unit like minutes or hours (1 min=60 s1\text{ min} = 60\text{ s}, 1 h=3600 s1\text{ h} = 3600\text{ s}).

  • Underline the target unit in the problem prompt and perform the unit conversion as your final step before boxing your answer.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall the unit conversion relationship: 1 min=60 s1\text{ min} = 60\text{ s}.

  2. Convert seconds to minutes by dividing by 60 s/min60\text{ s/min}: Δt=3600 s60 s/min=60.0 min\Delta t = \frac{3600\text{ s}}{60\text{ s/min}} = 60.0\text{ min}.

Final answer

(a) Δt=60.0 min\Delta t = 60.0\text{ min}; (b) R=34.6 ΩR = 34.6\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Before boxing your final answer, re-read the prompt to ensure your final numerical value matches the requested unit.

  • Practice writing explicit units at each substitution stage to maintain awareness of dimensions throughout the calculation.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers the power-voltage-resistance relationship as P = V / R without squaring the voltage, resulting in an incorrect resistance of 0.314 Ω.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δt=EP=1.26×106350=3600 s  ⟹  Δt=360060=60 min\Delta t = \frac{E}{P} = \frac{1.26 \times 10^6}{350} = 3600\text{ s} \implies \Delta t = \frac{3600}{60} = 60\text{ min}

  2. Step 2

    P=VR  ⟹  R=VPP = \frac{V}{R} \implies R = \frac{V}{P}

    Correct

    P=V2R  ⟹  R=V2PP = \frac{V^2}{R} \implies R = \frac{V^2}{P}

    You misstated the formula relating power, voltage, and resistance as P=VRP = \frac{V}{R}. Electric power is given by P=IVP = IV; combining this with Ohm's law (I=VRI = \frac{V}{R}) gives P=V2RP = \frac{V^2}{R}.

  3. Step 3

    R=110350=0.314 ΩR = \frac{110}{350} = 0.314\ \Omega

    Correct

    R=1102350=12100350≈34.6 ΩR = \frac{110^2}{350} = \frac{12100}{350} \approx 34.6\ \Omega

    Your arithmetic was carried out correctly based on your equation, but because the voltage was not squared, the resulting resistance value is incorrect.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of electric power as the rate of energy consumption to find the operating duration.

You performed the unit conversion from seconds to minutes cleanly and accurately.

You correctly isolated the resistance variable algebraically from your initial formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion between Ohm's law and electrical power

You wrote P=VRP = \frac{V}{R} instead of squaring the voltage to get P=V2RP = \frac{V^2}{R}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You likely confused Ohm's law for current (I=VRI = \frac{V}{R}) with the expression for electric power in terms of voltage and resistance (P=V2RP = \frac{V^2}{R}). Remember that electric power is P=IVP = IV, so substituting I=VRI = \frac{V}{R} introduces a factor of VV in the numerator, yielding V2V^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Deriving the Power Formulas
  • P=IV=I2R=V2RP = IV = I^2 R = \frac{V^2}{R}

  • Whenever you need power from voltage and resistance, derive it quickly from P=IVP = IV by substituting I=VRI = \frac{V}{R} to verify that VV is squared.

Dimensional / Unit Check
  • [VR]=Amperes=Current[\frac{V}{R}] = \text{Amperes} = \text{Current}, whereas [V2R]=Watts=Power[\frac{V^2}{R}] = \text{Watts} = \text{Power}

  • Check the units of your expression before plugging in numbers: VR\frac{V}{R} has units of current (extA ext{A}), not power (extW ext{W}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State Joule's law relating power, potential difference, and resistance: P=V2RP = \frac{V^2}{R}.

  2. Rearrange the equation to isolate resistance: R=V2PR = \frac{V^2}{P}.

  3. Substitute V=110 VV = 110\text{ V} and P=350 WP = 350\text{ W}: R=(110 V)2350 W=12100350≈34.6 ΩR = \frac{(110\text{ V})^2}{350\text{ W}} = \frac{12100}{350} \approx 34.6\ \Omega.

Final answer

(a) Δt=60.0 min\Delta t = 60.0\text{ min}; (b) R=34.6 ΩR = 34.6\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the three core representations of electric power: P=IVP = IV, P=I2RP = I^2 R, and P=V2RP = \frac{V^2}{R}.

  • Practice dimensional checks on circuit equations so you immediately catch when an expression yields current (extA ext{A}) instead of power (extW ext{W}).

  • Solve follow-up circuit problems where you alternate between finding resistance from current and from voltage.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly multiplies by 60 instead of dividing by 60 when converting seconds to minutes, yielding an operating time of 216000 min.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δt=EP=1.26×106350=3600 s\Delta t = \frac{E}{P} = \frac{1.26 \times 10^6}{350} = 3600\text{ s}

  2. Step 2

    Δt=3600×60=216000 min\Delta t = 3600 \times 60 = 216000\text{ min}

    Correct

    Δt=3600 s60 s/min=60.0 min\Delta t = \frac{3600\text{ s}}{60\text{ s/min}} = 60.0\text{ min}

    Converting from a smaller unit (seconds) to a larger unit (minutes) requires dividing by 6060, not multiplying.

  3. Step 3

    R=V2P=1102350  ⟹  R=12100350=34.6 ΩR = \frac{V^2}{P} = \frac{110^2}{350} \implies R = \frac{12100}{350} = 34.6\ \Omega

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly selected and rearranged the electrical energy-power formula Δt=EP\Delta t = \frac{E}{P}.

You accurately computed the duration in SI units as 3600 s3600\text{ s}.

You used the correct power-voltage-resistance formula R=V2PR = \frac{V^2}{P} and evaluated it to 34.6 Ω34.6\ \Omega.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted unit conversion factor

You accidentally multiplied by 6060 instead of dividing by 6060 when changing seconds into minutes.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the direction of conversion between smaller and larger units without carrying explicit conversion units (dimensional analysis) to cancel units algebraically.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Scaling Sanity Check
  • When expressing a fixed time interval in a larger unit, the numerical value must decrease.

  • Check whether minutes should be a smaller number than seconds: since 1 min=60 s1\text{ min} = 60\text{ s}, the value in minutes must be much smaller than 36003600.

Fractional Unit Cancellation
  • Multiply by conversion factors structured so that unwanted units cancel: s×1 min60 s=min\text{s} \times \frac{1\text{ min}}{60\text{ s}} = \text{min}.

  • Write the conversion factor explicitly as a fraction with s\text{s} in the denominator to ensure it cancels.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the conversion using unit fractions: Δt=3600 s×1 min60 s\Delta t = 3600\text{ s} \times \frac{1\text{ min}}{60\text{ s}}.

  2. Divide 36003600 by 6060: Δt=60.0 min\Delta t = 60.0\text{ min}.

Final answer

(a) Δt=60.0 min\Delta t = 60.0\text{ min}; (b) R=34.6 ΩR = 34.6\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice writing unit conversion factors as explicit multiplying fractions (e.g., 1 min60 s\frac{1\text{ min}}{60\text{ s}}) to visually confirm unit cancellation.

  • Always perform a magnitude sanity check: a duration measured in minutes must be numerically smaller than the same duration measured in seconds.

Lock it in

Similar question

01

A 500 W500\ \text{W} electric kettle uses 4.50×105 J4.50 \times 10^5\ \text{J} of electrical energy to boil water. Calculate the operating duration of the kettle in minutes.

Answer

Δt=15.0 min\Delta t = 15.0\ \text{min}. Key steps: Δt=EP=4.50×105 J500 W=900 s\Delta t = \frac{E}{P} = \frac{4.50 \times 10^5\ \text{J}}{500\ \text{W}} = 900\ \text{s}; convert to minutes: Δt=900 s60 s/min=15.0 min\Delta t = \frac{900\ \text{s}}{60\ \text{s/min}} = 15.0\ \text{min}.

02

An electric immersion heater with an internal resistance of 24.2 Ω24.2\ \Omega is connected across a 220 V220\ \text{V} DC source. (a) Determine its power dissipation PP. (b) Calculate the time required in minutes to deliver 1.20×106 J1.20 \times 10^6\ \text{J} of energy.

Answer

(a) P=2000 WP = 2000\ \text{W}; (b) Δt=10.0 min\Delta t = 10.0\ \text{min}. Key steps: P=V2R=(220 V)224.2 Ω=2000 WP = \frac{V^2}{R} = \frac{(220\ \text{V})^2}{24.2\ \Omega} = 2000\ \text{W}; Δt=EP=1.20×106 J2000 W=600 s\Delta t = \frac{E}{P} = \frac{1.20 \times 10^6\ \text{J}}{2000\ \text{W}} = 600\ \text{s}; Δt=600 s60 s/min=10.0 min\Delta t = \frac{600\ \text{s}}{60\ \text{s/min}} = 10.0\ \text{min}.

03

A DC heating element operates at a potential difference of V=120 VV = 120\ \text{V} and draws a current of I=5.0 AI = 5.0\ \text{A}. If it consumes a total energy of 4.32×106 J4.32 \times 10^6\ \text{J}, determine the operating duration in hours.

Answer

Δt=2.0 h\Delta t = 2.0\ \text{h}. Key steps: P=VI=(120 V)(5.0 A)=600 WP = V I = (120\ \text{V})(5.0\ \text{A}) = 600\ \text{W}; Δt=EP=4.32×106 J600 W=7200 s\Delta t = \frac{E}{P} = \frac{4.32 \times 10^6\ \text{J}}{600\ \text{W}} = 7200\ \text{s}; convert to hours: Δt=7200 s3600 s/h=2.0 h\Delta t = \frac{7200\ \text{s}}{3600\ \text{s/h}} = 2.0\ \text{h}.

Loading workspace…