Resources

In human biomechanics, the human forearm acts as a third-class lever when lifting a weight in the hand. The elbow joint serves as the fulcrum, the biceps muscle exerts an upward effort force attached approximately dE=4.00 cmd_E = 4.00\text{ cm} from the joint, and a m=8.00 kgm = 8.00\text{ kg} dumbbell is held in the hand at a distance of dL=36.0 cmd_L = 36.0\text{ cm} from the joint. Students often assume that simple machines always make forces smaller (i.e., MA>1\text{MA} > 1). With the forearm held horizontally and taking g=9.80 m/s2g = 9.80\text{ m/s}^2 (neglecting the forearm's mass): (a) calculate the ideal mechanical advantage (IMA\text{IMA}) of the forearm lever, (b) calculate the tension force FbicepsF_{\text{biceps}} required by the biceps, and (c) calculate the ratio of the distance moved by the hand ΔyL\Delta y_L to the contraction distance of the biceps muscle ΔyE\Delta y_E when the arm flexes through a small angle.

Answer and steps

Final answer

(a) IMA=0.111\text{IMA} = 0.111; (b) Fbiceps=706 NF_{\text{biceps}} = 706\text{ N}; (c) ΔyLΔyE=9.00\frac{\Delta y_L}{\Delta y_E} = 9.00

Steps

(a) Calculating the Ideal Mechanical Advantage (IMA\text{IMA})

A lever's ideal mechanical advantage is defined as the ratio of the effort arm distance (dEd_E) to the load arm distance (dLd_L) measured from the pivot (elbow joint):

IMA=dEdL\text{IMA} = \frac{d_E}{d_L}

Substitute the given lever arm lengths:

IMA=4.00 cm36.0 cm=19≈0.111\text{IMA} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = \frac{1}{9} \approx 0.111

Key Concept: A third-class lever always has the effort applied between the fulcrum and the load (dE<dLd_E < d_L), which means IMA<1\text{IMA} < 1. A common pitfall is assuming simple machines must always reduce the required force; third-class levers intentionally sacrifice force advantage to gain distance and speed.


(b) Determining the Muscle Tension (FbicepsF_{\text{biceps}})

First, determine the downward force exerted by the dumbbell due to gravity:

FL=mg=(8.00 kg)(9.80 m/s2)=78.4 NF_L = m g = (8.00\text{ kg})(9.80\text{ m/s}^2) = 78.4\text{ N}

For the forearm held horizontally in static equilibrium, the net torque about the elbow fulcrum must be zero:

∑τelbow=0\sum \tau_{\text{elbow}} = 0

Taking counterclockwise torque as positive:

Fbiceps⋅dE−FL⋅dL=0F_{\text{biceps}} \cdot d_E - F_L \cdot d_L = 0

Rearranging for the biceps force:

Fbiceps=FL(dLdE)=FLIMAF_{\text{biceps}} = F_L \left(\frac{d_L}{d_E}\right) = \frac{F_L}{\text{IMA}}

Substitute the values:

Fbiceps=(78.4 N)(36.0 cm4.00 cm)=78.4 N×9=705.6 N≈706 NF_{\text{biceps}} = (78.4\text{ N})\left(\frac{36.0\text{ cm}}{4.00\text{ cm}}\right) = 78.4\text{ N} \times 9 = 705.6\text{ N} \approx 706\text{ N}

The muscle must exert approximately 706 N706\text{ N} of upward tension—nine times the weight of the dumbbell—because its lever arm is nine times shorter than the load arm.


(c) Finding the Ratio of Displacements (ΔyL/ΔyE\Delta y_L / \Delta y_E)

When the forearm rotates upward through a small angle Δθ\Delta \theta (measured in radians) about the elbow pivot, the vertical displacement of any point along the forearm is directly proportional to its distance from the joint:

ΔyE=dE⋅Δθ\Delta y_E = d_E \cdot \Delta \theta

ΔyL=dL⋅Δθ\Delta y_L = d_L \cdot \Delta \theta

Dividing the hand's displacement by the biceps' contraction distance yields:

ΔyLΔyE=dL⋅ΔθdE⋅Δθ=dLdE=1IMA\frac{\Delta y_L}{\Delta y_E} = \frac{d_L \cdot \Delta \theta}{d_E \cdot \Delta \theta} = \frac{d_L}{d_E} = \frac{1}{\text{IMA}}

Substitute the distances:

ΔyLΔyE=36.0 cm4.00 cm=9.00\frac{\Delta y_L}{\Delta y_E} = \frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00

This demonstrates the evolutionary advantage of third-class levers in human limbs: a small contraction of the biceps muscle produces a displacement nine times larger at the hand, enabling rapid and extensive hand movements.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student inverts the definition of mechanical advantage by dividing the load arm by the effort arm, assuming mechanical advantage must always be greater than 1.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    IMA=dLdE  ⟹  IMA=36.0 cm4.00 cm=9.00\text{IMA} = \frac{d_L}{d_E} \implies \text{IMA} = \frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00

    Correct

    IMA=dEdL=4.00 cm36.0 cm=19≈0.111\text{IMA} = \frac{d_E}{d_L} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = \frac{1}{9} \approx 0.111

    The ideal mechanical advantage is defined as the ratio of effort distance to load distance, IMA=dEdL\text{IMA} = \frac{d_E}{d_L}. For a third-class lever where the effort acts closer to the pivot than the load, IMA\text{IMA} is strictly less than 11.

  2. Step 2

    Fload=8.00 kg×9.80 m/s2=78.4 N  ⟹  Fbiceps×4.00 cm=78.4 N×36.0 cm  ⟹  Fbiceps=705.6 NF_{\text{load}} = 8.00\text{ kg} \times 9.80\text{ m/s}^2 = 78.4\text{ N} \implies F_{\text{biceps}} \times 4.00\text{ cm} = 78.4\text{ N} \times 36.0\text{ cm} \implies F_{\text{biceps}} = 705.6\text{ N}

  3. Step 3

    ΔyLΔyE=36.0 cm4.00 cm=9.00\frac{\Delta y_L}{\Delta y_E} = \frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00

WHAT YOU DID WELL
Compliments from Your Teacher

You set up and evaluated the torque equilibrium equation about the elbow joint correctly.

You correctly calculated the ratio of hand displacement to muscle displacement using proportional arc lengths.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Mechanical Advantage Definition

No, this is a conceptual misunderstanding about the definition and range of mechanical advantage for third-class levers.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that mechanical advantage must always be greater than 1, leading you to set the ratio as larger distancesmaller distance\frac{\text{larger distance}}{\text{smaller distance}} (dL/dEd_L / d_E) instead of the standard definition of effort distance divided by load distance (dE/dLd_E / d_L).

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Ideal Mechanical Advantage (IMA)
  • For any simple machine or lever, IMA=deffortdload\text{IMA} = \frac{d_{\text{effort}}}{d_{\text{load}}}.

  • Always place the effort arm in the numerator and the load arm in the denominator, even when the resulting ratio is less than 11.

Nature of Third-Class Levers
  • Third-class levers have the effort applied between the fulcrum and the load (dE<dLd_E < d_L), which guarantees IMA<1\text{IMA} < 1.

  • Remember that human limbs trade force for speed and range of motion; a value of IMA<1\text{IMA} < 1 is physically expected.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the standard definition of ideal mechanical advantage: IMA=dEdL\text{IMA} = \frac{d_E}{d_L}.

  2. Substitute the given effort arm dE=4.00 cmd_E = 4.00\text{ cm} and load arm dL=36.0 cmd_L = 36.0\text{ cm}: IMA=4.00 cm36.0 cm=19≈0.111\text{IMA} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = \frac{1}{9} \approx 0.111.

Final answer

(a) IMA=0.111\text{IMA} = 0.111; (b) Fbiceps=706 NF_{\text{biceps}} = 706\text{ N}; (c) ΔyLΔyE=9.00\frac{\Delta y_L}{\Delta y_E} = 9.00

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three lever classes to see why third-class levers always have an IMA less than 1.

  • Practice checking whether a machine is designed to magnify force (IMA > 1) or magnify displacement and speed (IMA < 1) before writing the ratio.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to multiply the mass by gravitational acceleration to find force, directly using mass in kilograms in the torque equilibrium equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    IMA=dEdL  ⟹  IMA=4.00 cm36.0 cm=0.111\text{IMA} = \frac{d_E}{d_L} \implies \text{IMA} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = 0.111

  2. Step 2

    Fbiceps⋅dE=m⋅dL  ⟹  Fbiceps⋅4.00 cm=8.00 kg⋅36.0 cm  ⟹  Fbiceps=72.0 NF_{\text{biceps}} \cdot d_E = m \cdot d_L \implies F_{\text{biceps}} \cdot 4.00\text{ cm} = 8.00\text{ kg} \cdot 36.0\text{ cm} \implies F_{\text{biceps}} = 72.0\text{ N}

    Correct

    Fbiceps⋅dE=(mg)⋅dL  ⟹  Fbiceps=(8.00 kg)(9.80 m/s2)(36.0 cm)4.00 cm=705.6 N≈706 NF_{\text{biceps}} \cdot d_E = (mg) \cdot d_L \implies F_{\text{biceps}} = \frac{(8.00\text{ kg})(9.80\text{ m/s}^2)(36.0\text{ cm})}{4.00\text{ cm}} = 705.6\text{ N} \approx 706\text{ N}

    Torque is defined as force multiplied by perpendicular lever arm distance (τ=F⋅d\tau = F \cdot d), not mass times distance. You need to multiply the 8.00 kg8.00\text{ kg} mass by g=9.80 m/s2g = 9.80\text{ m/s}^2 to obtain the downward load force FL=78.4 NF_L = 78.4\text{ N} before balancing torques.

  3. Step 3

    ΔyLΔyE=dLdE=36.0 cm4.00 cm=9.00\frac{\Delta y_L}{\Delta y_E} = \frac{d_L}{d_E} = \frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the forearm as a lever and calculated the ideal mechanical advantage using the ratio of effort arm to load arm.

You correctly set up the rotational equilibrium condition equating clockwise and counterclockwise torques about the elbow fulcrum.

You correctly derived the displacement amplification ratio from the lever arm geometry.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing Mass with Force in Torque Balance

You substituted the dumbbell's mass (8.00 kg8.00\text{ kg}) directly into the torque balance equation instead of multiplying by g=9.80 m/s2g = 9.80\text{ m/s}^2 to find the force of gravity.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Torque requires force (extN ext{N}), whereas mass (extkg ext{kg}) is a measure of inertia. In static equilibrium problems on Earth, an object's downward load force is its weight W=mgW = mg, so the gravitational torque is (mg)⋅d(mg) \cdot d, not m⋅dm \cdot d.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check the units of torque
  • Torque has SI units of newton-meters (N⋅m\text{N}\cdot\text{m}), meaning every torque term must be a force (in N\text{N}) multiplied by a lever arm (in m\text{m}).

  • Whenever you see a mass given in kg\text{kg}, convert it immediately to a downward force using Fg=mgF_g = mg before entering it into ∑τ=0\sum \tau = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the weight of the dumbbell: FL=mg=(8.00 kg)(9.80 m/s2)=78.4 NF_L = mg = (8.00\text{ kg})(9.80\text{ m/s}^2) = 78.4\text{ N}.

  2. Apply rotational equilibrium about the elbow fulcrum: ∑τ=Fbiceps⋅dE−FL⋅dL=0\sum \tau = F_{\text{biceps}} \cdot d_E - F_L \cdot d_L = 0.

  3. Solve for the muscle tension: Fbiceps=FL⋅dLdE=(78.4 N)⋅36.0 cm4.00 cm=78.4 N×9=705.6 N≈706 NF_{\text{biceps}} = F_L \cdot \frac{d_L}{d_E} = (78.4\text{ N}) \cdot \frac{36.0\text{ cm}}{4.00\text{ cm}} = 78.4\text{ N} \times 9 = 705.6\text{ N} \approx 706\text{ N}.

Final answer

(a) IMA=0.111\text{IMA} = 0.111; (b) Fbiceps=706 NF_{\text{biceps}} = 706\text{ N}; (c) ΔyLΔyE=9.00\frac{\Delta y_L}{\Delta y_E} = 9.00

NEXT STEPS
Final Takeaways from Your Teacher
  • Perform a quick dimensional check on every torque equation to confirm every term has units of N⋅m\text{N}\cdot\text{m} (or N⋅cm\text{N}\cdot\text{cm}).

  • Practice drawing free-body diagrams that explicitly label weight forces as mgmg rather than just mm.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the displacement ratio by assuming that the smaller muscle displacement corresponds to the numerator.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    IMA=dEdL=4.00 cm36.0 cm=0.111\text{IMA} = \frac{d_E}{d_L} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = 0.111

  2. Step 2

    Fload=8.00 kg⋅9.80 m/s2=78.4 N  ⟹  Fbiceps⋅4.00 cm=78.4 N⋅36.0 cm  ⟹  Fbiceps=705.6 NF_{\text{load}} = 8.00\text{ kg} \cdot 9.80\text{ m/s}^2 = 78.4\text{ N} \implies F_{\text{biceps}} \cdot 4.00\text{ cm} = 78.4\text{ N} \cdot 36.0\text{ cm} \implies F_{\text{biceps}} = 705.6\text{ N}

  3. Step 3

    ΔyLΔyE=dEdL=4.00 cm36.0 cm=0.111\frac{\Delta y_L}{\Delta y_E} = \frac{d_E}{d_L} = \frac{4.00\text{ cm}}{36.0\text{ cm}} = 0.111

    Correct

    ΔyLΔyE=dLΔθdEΔθ=dLdE=36.0 cm4.00 cm=9.00\frac{\Delta y_L}{\Delta y_E} = \frac{d_L \Delta \theta}{d_E \Delta \theta} = \frac{d_L}{d_E} = \frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00

    Because points on the rotating forearm share the same angular displacement Δθ\Delta \theta, linear arc displacement is directly proportional to radius (Δy=dΔθ\Delta y = d \Delta \theta). Therefore, the hand at distance dLd_L moves farther than the muscle attachment at dEd_E, making the displacement ratio ΔyLΔyE=dLdE=1IMA=9.00\frac{\Delta y_L}{\Delta y_E} = \frac{d_L}{d_E} = \frac{1}{\text{IMA}} = 9.00.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the effort arm and load arm to compute the ideal mechanical advantage.

You accurately converted the load mass to a gravitational force and applied rotational equilibrium to determine the biceps force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted displacement ratio in lever rotation

You equated the ratio of displacements directly to IMA\text{IMA} rather than recognizing that linear displacement is proportional to distance from the fulcrum.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the force multiplier with the distance multiplier. In a lever, work conservation dictates that force and displacement are inversely related: a machine with IMA<1\text{IMA} < 1 requires more input force but produces a correspondingly larger output displacement (fracΔyLΔyE=1IMA\\frac{\Delta y_L}{\Delta y_E} = \frac{1}{\text{IMA}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Circular Arc Displacement
  • For a rigid body rotating through angle Δθ\Delta \theta, linear travel is Δs=rΔθ\Delta s = r \Delta \theta. Points farther from the pivot sweep out greater distances.

  • Check which point is farther from the pivot; that point must have the larger displacement in the numerator or denominator.

Trade-off in Third-Class Levers
  • Third-class levers have IMA<1\text{IMA} < 1, sacrificing force advantage to gain a distance and speed advantage.

  • Ensure that the hand displacement ΔyL\Delta y_L is larger than the muscle contraction ΔyE\Delta y_E, yielding a ratio greater than 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Relate the linear displacement of each point to the small rotation angle Δθ\Delta \theta: ΔyL=dLΔθ\Delta y_L = d_L \Delta \theta and ΔyE=dEΔθ\Delta y_E = d_E \Delta \theta.

  2. Form the ratio of hand displacement to muscle displacement: ΔyLΔyE=dLΔθdEΔθ=dLdE\frac{\Delta y_L}{\Delta y_E} = \frac{d_L \Delta \theta}{d_E \Delta \theta} = \frac{d_L}{d_E}.

  3. Substitute dL=36.0 cmd_L = 36.0\text{ cm} and dE=4.00 cmd_E = 4.00\text{ cm} to evaluate the ratio: 36.0 cm4.00 cm=9.00\frac{36.0\text{ cm}}{4.00\text{ cm}} = 9.00.

Final answer

(a) IMA=0.111\text{IMA} = 0.111; (b) Fbiceps=706 NF_{\text{biceps}} = 706\text{ N}; (c) ΔyLΔyE=9.00\frac{\Delta y_L}{\Delta y_E} = 9.00

NEXT STEPS
Final Takeaways from Your Teacher
  • Review circular motion kinematics where arc length equals radius times angular displacement (Δs=rΔθ\Delta s = r \Delta \theta).

  • Check your final ratio against physical intuition: since the hand is farther from the elbow joint than the tendon, flexing the arm must move the hand through a much larger distance than the muscle contracts.

Lock it in

Similar question

01

A pair of tweezers acts as a third-class lever. Your fingers apply a pinch force at a distance of 3.0 cm3.0\text{ cm} from the joined end (fulcrum), while the tips grasp an object 9.0 cm9.0\text{ cm} from the fulcrum. Calculate the ideal mechanical advantage (IMA) of the tweezers.

Answer

IMA=dEdL=3.0 cm9.0 cm=13≈0.333\text{IMA} = \frac{d_E}{d_L} = \frac{3.0\text{ cm}}{9.0\text{ cm}} = \frac{1}{3} \approx 0.333.

02

A person uses a broom to sweep a floor. The upper hand acts as the pivot, the lower hand applies an effort force 0.40 m0.40\text{ m} below the pivot, and the bristles touch the floor 1.60 m1.60\text{ m} below the pivot. If the floor offers a frictional resistance of 15 N15\text{ N} against the bristles, calculate (a) the IMA\text{IMA} of the broom and (b) the effort force required by the lower hand (assuming static balance).

Answer

(a) IMA=dEdL=0.40 m1.60 m=0.25\text{IMA} = \frac{d_E}{d_L} = \frac{0.40\text{ m}}{1.60\text{ m}} = 0.25. (b) By torque balance about the pivot: FE⋅dE=FL⋅dL  ⟹  FE=15 N×(1.60 m0.40 m)=60 NF_E \cdot d_E = F_L \cdot d_L \implies F_E = 15\text{ N} \times \left(\frac{1.60\text{ m}}{0.40\text{ m}}\right) = 60\text{ N}.

03

When chewing, the human jaw functions as a third-class lever. The temporomandibular joint (TMJ) is the fulcrum. The masseter muscle attaches 3.5 cm3.5\text{ cm} anterior to the joint, while the incisor teeth are located 8.0 cm8.0\text{ cm} anterior to the joint. If a bite force of 140 N140\text{ N} is exerted at the incisors, find (a) the lever's IMA\text{IMA}, (b) the upward muscle force exerted by the masseter, and (c) the ratio of incisor displacement to muscle contraction distance.

Answer

(a) IMA=dEdL=3.5 cm8.0 cm=716≈0.438\text{IMA} = \frac{d_E}{d_L} = \frac{3.5\text{ cm}}{8.0\text{ cm}} = \frac{7}{16} \approx 0.438. (b) Torque balance: Fmuscle=FbiteIMA=140 N0.4375=320 NF_{\text{muscle}} = \frac{F_{\text{bite}}}{\text{IMA}} = \frac{140\text{ N}}{0.4375} = 320\text{ N}. (c) ΔyincisorΔymuscle=dLdE=1IMA=8.0 cm3.5 cm≈2.29\frac{\Delta y_{\text{incisor}}}{\Delta y_{\text{muscle}}} = \frac{d_L}{d_E} = \frac{1}{\text{IMA}} = \frac{8.0\text{ cm}}{3.5\text{ cm}} \approx 2.29.

Loading workspace…