Resources

In a precision micro-hydraulic positioner, an ultra-fine control plunger of radius r1=0.250 mmr_1 = 0.250\text{ mm} drives an actuator platform of radius r2=12.5 mmr_2 = 12.5\text{ mm} via an incompressible, degassed hydraulic fluid. To investigate the behavior under extreme geometric scaling, find: (a) the theoretical mechanical advantage MA=F2F1\text{MA} = \frac{F_2}{F_1} of the system, and (b) the stroke displacement d1d_1 of the micro-plunger required to advance the actuator platform by an incremental distance of d2=1.60 μmd_2 = 1.60\text{ }\mu\text{m}.

Answer and steps

Final answer

(a) MA=2500\text{MA} = 2500; (b) d1=4.00 mmd_1 = 4.00\text{ mm}

Steps

Part (a): Theoretical Mechanical Advantage (MA\text{MA})

By Pascal's principle, any change in pressure applied to an enclosed, incompressible fluid is transmitted undiminished to every portion of the fluid and to the walls of its container.

  1. Relate pressure, force, and area: The hydrostatic pressure PP created by the input force F1F_1 on the micro-plunger cross-sectional area A1A_1 is: P1=F1A1P_1 = \frac{F_1}{A_1}

    This same pressure acts on the actuator platform of area A2A_2, producing an output force F2F_2: P2=F2A2P_2 = \frac{F_2}{A_2}

    Since P1=P2P_1 = P_2: F1A1=F2A2  ⟹  MA=F2F1=A2A1\frac{F_1}{A_1} = \frac{F_2}{A_2} \implies \text{MA} = \frac{F_2}{F_1} = \frac{A_2}{A_1}

  2. Calculate the ratio of the cross-sectional areas: The cross-sectional area of a cylinder is A=πr2A = \pi r^2. Therefore, the area ratio depends on the square of the radii: MA=πr22πr12=(r2r1)2\text{MA} = \frac{\pi r_2^2}{\pi r_1^2} = \left(\frac{r_2}{r_1}\right)^2

    Given r1=0.250 mmr_1 = 0.250\text{ mm} and r2=12.5 mmr_2 = 12.5\text{ mm}: r2r1=12.5 mm0.250 mm=50\frac{r_2}{r_1} = \frac{12.5\text{ mm}}{0.250\text{ mm}} = 50

    MA=(50)2=2500\text{MA} = (50)^2 = 2500


Part (b): Plunger Stroke Displacement (d1d_1)

  1. Conservation of fluid volume: Because the hydraulic fluid is incompressible, the volume of fluid displaced by the micro-plunger (ΔV1\Delta V_1) must equal the volume gained under the actuator platform (ΔV2\Delta V_2): ΔV1=ΔV2\Delta V_1 = \Delta V_2 A1d1=A2d2A_1 d_1 = A_2 d_2
  2. Solve for the stroke displacement d1d_1: d1=(A2A1)d2=MA⋅d2d_1 = \left(\frac{A_2}{A_1}\right) d_2 = \text{MA} \cdot d_2

    Substitute MA=2500\text{MA} = 2500 and d2=1.60 μmd_2 = 1.60\text{ }\mu\text{m}: d1=2500⋅(1.60 μm)=4000 μmd_1 = 2500 \cdot (1.60\text{ }\mu\text{m}) = 4000\text{ }\mu\text{m}

    Converting to millimeters: d1=4000 μm1000 μm/mm=4.00 mmd_1 = \frac{4000\text{ }\mu\text{m}}{1000\text{ }\mu\text{m/mm}} = 4.00\text{ mm}

Common Pitfall: Mechanical advantage scales with the square of the radius ratio (r2r1)2(\frac{r_2}{r_1})^2, not linearly with r2r1\frac{r_2}{r_1}. Furthermore, while force is magnified by a factor of 25002500, displacement is reduced by that same factor, illustrating the trade-off between force amplification and stroke distance governed by work and volume conservation.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the ratio of circular cross-sectional areas with the simple linear ratio of radii, neglecting to square the radius ratio.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    MA=F2F1=r2r1  ⟹  MA=12.5 mm0.250 mm=50\text{MA} = \frac{F_2}{F_1} = \frac{r_2}{r_1} \implies \text{MA} = \frac{12.5\text{ mm}}{0.250\text{ mm}} = 50

    Correct

    MA=F2F1=A2A1=πr22πr12=(r2r1)2=(12.5 mm0.250 mm)2=502=2500\text{MA} = \frac{F_2}{F_1} = \frac{A_2}{A_1} = \frac{\pi r_2^2}{\pi r_1^2} = \left(\frac{r_2}{r_1}\right)^2 = \left(\frac{12.5\text{ mm}}{0.250\text{ mm}}\right)^2 = 50^2 = 2500

    Pascal's principle states that pressure is transmitted equally, so F2F1=A2A1\frac{F_2}{F_1} = \frac{A_2}{A_1}. Because the pistons have circular faces, the area scales with the square of the radius, (r2r1)2\left(\frac{r_2}{r_1}\right)^2, rather than linearly with r2r1\frac{r_2}{r_1}.

  2. Step 2

    A1d1=A2d2A_1 d_1 = A_2 d_2

  3. Step 3

    d1=r2r1×d2  ⟹  d1=50×1.60 μm=80 μmd_1 = \frac{r_2}{r_1} \times d_2 \implies d_1 = 50 \times 1.60\text{ }\mu\text{m} = 80\text{ }\mu\text{m}

    Correct

    d1=A2A1d2=(r2r1)2d2=2500×1.60 μm=4000 μm=4.00 mmd_1 = \frac{A_2}{A_1} d_2 = \left(\frac{r_2}{r_1}\right)^2 d_2 = 2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m} = 4.00\text{ mm}

    When solving for d1d_1, the area ratio A2A1\frac{A_2}{A_1} equals (r2r1)2=2500\left(\frac{r_2}{r_1}\right)^2 = 2500. Multiplying by the squared radius ratio yields d1=4.00 mmd_1 = 4.00\text{ mm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the hydraulic fluid is incompressible and set up the volume conservation equation A1d1=A2d2A_1 d_1 = A_2 d_2.

You accurately computed the linear radius ratio r2r1=50\frac{r_2}{r_1} = 50.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional Scaling Misconception

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the ratio of circular piston cross-sections as a linear ratio of radii rather than squaring the radius ratio according to the area formula A=πr2A = \pi r^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Area Scaling Rule
  • For circular pistons, the cross-sectional area is A=πr2A = \pi r^2, making the area ratio A2A1=(r2r1)2\frac{A_2}{A_1} = \left(\frac{r_2}{r_1}\right)^2.

  • Always write down A=πr2A = \pi r^2 before substituting radii into force or volume formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Pascal's principle to find mechanical advantage: MA=F2F1=A2A1=(r2r1)2\text{MA} = \frac{F_2}{F_1} = \frac{A_2}{A_1} = \left(\frac{r_2}{r_1}\right)^2.

  2. Substitute the given radii: MA=(12.5 mm0.250 mm)2=502=2500\text{MA} = \left(\frac{12.5\text{ mm}}{0.250\text{ mm}}\right)^2 = 50^2 = 2500.

  3. Use conservation of volume to find displacement: d1=A2A1d2=MA⋅d2d_1 = \frac{A_2}{A_1} d_2 = \text{MA} \cdot d_2.

  4. Calculate d1=2500×1.60 μm=4000 μm=4.00 mmd_1 = 2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m} = 4.00\text{ mm}.

Final answer

(a) MA=2500\text{MA} = 2500; (b) d1=4.00 mmd_1 = 4.00\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how 1D dimensions (radii, diameters) scale to 2D areas (A∝r2A \propto r^2).

  • Practice deriving hydraulic relations directly from pressure equilibrium P1=P2P_1 = P_2 and volume conservation ΔV1=ΔV2\Delta V_1 = \Delta V_2.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the relationship between mechanical advantage and displacement, mistakenly dividing the output displacement by the mechanical advantage instead of multiplying it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    MA=(r2r1)2  ⟹  MA=(12.50.250)2=502=2500\text{MA} = \left(\frac{r_2}{r_1}\right)^2 \implies \text{MA} = \left(\frac{12.5}{0.250}\right)^2 = 50^2 = 2500

  2. Step 2

    d1=d2MA  ⟹  d1=1.60 μm2500=0.00064 μm=6.40×10−10 md_1 = \frac{d_2}{\text{MA}} \implies d_1 = \frac{1.60\text{ }\mu\text{m}}{2500} = 0.00064\text{ }\mu\text{m} = 6.40 \times 10^{-10}\text{ m}

    Correct

    A1d1=A2d2  ⟹  d1=(A2A1)d2=MA⋅d2=2500⋅(1.60 μm)=4000 μm=4.00 mmA_1 d_1 = A_2 d_2 \implies d_1 = \left(\frac{A_2}{A_1}\right) d_2 = \text{MA} \cdot d_2 = 2500 \cdot (1.60\text{ }\mu\text{m}) = 4000\text{ }\mu\text{m} = 4.00\text{ mm}

    Because the fluid is incompressible, fluid volume is conserved (A1d1=A2d2A_1 d_1 = A_2 d_2). Since the input plunger has a much smaller area, it must travel a much greater distance (d1=MA⋅d2d_1 = \text{MA} \cdot d_2) rather than a smaller distance.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the mechanical advantage equals the ratio of cross-sectional areas.

You properly squared the radius ratio to obtain MA=2500\text{MA} = 2500.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted displacement-to-mechanical advantage ratio

You divided the output displacement by MA\text{MA} instead of multiplying it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated displacement as if it scaled directly with the force ratio rather than through volume conservation (A1d1=A2d2A_1 d_1 = A_2 d_2) or energy conservation (F1d1=F2d2F_1 d_1 = F_2 d_2), which requires a trade-off where force amplification demands a proportionally larger input stroke.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservation of Fluid Volume
  • For an incompressible fluid, ΔV1=ΔV2\Delta V_1 = \Delta V_2, meaning A1d1=A2d2A_1 d_1 = A_2 d_2.

  • Always write the volume conservation equation before solving for displacement to verify whether you need to multiply or divide by the area ratio.

Work and Mechanical Trade-off
  • In an ideal hydraulic system, input work equals output work: W1=W2  ⟹  F1d1=F2d2W_1 = W_2 \implies F_1 d_1 = F_2 d_2.

  • Check your physical intuition: when a machine multiplies force by 25002500, the input distance must be 25002500 times larger than the output distance, never smaller.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the volume conservation equality: A1d1=A2d2A_1 d_1 = A_2 d_2.

  2. Solve for the input stroke: d1=(A2A1)d2=MA⋅d2d_1 = \left(\frac{A_2}{A_1}\right) d_2 = \text{MA} \cdot d_2.

  3. Substitute MA=2500\text{MA} = 2500 and d2=1.60 μmd_2 = 1.60\text{ }\mu\text{m}: d1=2500×1.60 μm=4000 μmd_1 = 2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m}.

  4. Convert micrometers to millimeters: d1=4000 μm1000 μm/mm=4.00 mmd_1 = \frac{4000\text{ }\mu\text{m}}{1000\text{ }\mu\text{m/mm}} = 4.00\text{ mm}.

Final answer

(a) MA=2500\text{MA} = 2500; (b) d1=4.00 mmd_1 = 4.00\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the trade-off principle in simple machines: force gain always corresponds to distance loss.

  • Practice deriving displacements directly from ΔV=A⋅d\Delta V = A \cdot d rather than memorizing multiplier formulas.

OverviewACEpath Teacher's Diagnosis

03 The student fails to convert the displacement d₂ from micrometers to millimeters or meters, writing the final value directly with millimetric magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    MA=(r2r1)2=(12.50.250)2=2500\text{MA} = \left(\frac{r_2}{r_1}\right)^2 = \left(\frac{12.5}{0.250}\right)^2 = 2500

  2. Step 2

    V1=V2V_1 = V_2

  3. Step 3

    d1=2500×1.60=4000 mmd_1 = 2500 \times 1.60 = 4000\text{ mm}

    Correct

    d1=2500×1.60 μm=4000 μm=4.00 mmd_1 = 2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m} = 4.00\text{ mm}

    You substituted d2=1.60 μmd_2 = 1.60\text{ }\mu\text{m} without carrying its unit, resulting in 4000 μm4000\text{ }\mu\text{m} which was erroneously labeled as 4000 mm4000\text{ mm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the squared ratio of the radii to calculate the mechanical advantage.

You recognized that fluid incompressibility requires equal volume displacement.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion omission

You calculated 2500×1.60=40002500 \times 1.60 = 4000 using the numerical value of micrometers, but appended millimeters as the final unit.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating given quantities as dimensionless numbers during intermediate substitution instead of carrying metric prefixes (1 μm=10−3 mm1\text{ }\mu\text{m} = 10^{-3}\text{ mm}) through the calculation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Carry Units in Every Calculation
  • Dimensionless scaling factors preserve the unit of the multiplied quantity: dimensionless×μm=μm\text{dimensionless} \times \mu\text{m} = \mu\text{m}.

  • Always write the unit alongside the numerical value during substitution: 2500×1.60 μm=4000 μm2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m}.

Prefix Conversion Check
  • 1 mm=1000 μm  ⟹  1 μm=10−3 mm1\text{ mm} = 1000\text{ }\mu\text{m} \implies 1\text{ }\mu\text{m} = 10^{-3}\text{ mm}.

  • Convert micro-units to milli-units by dividing by 1000 before reporting the final result.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute d2=1.60 μmd_2 = 1.60\text{ }\mu\text{m} with explicit units: d1=2500×1.60 μm=4000 μmd_1 = 2500 \times 1.60\text{ }\mu\text{m} = 4000\text{ }\mu\text{m}.

  2. Convert micrometers to millimeters: d1=4000 μm1000 μm/mm=4.00 mmd_1 = \frac{4000\text{ }\mu\text{m}}{1000\text{ }\mu\text{m/mm}} = 4.00\text{ mm}.

Final answer

(a) MA=2500\text{MA} = 2500; (b) d1=4.00 mmd_1 = 4.00\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write down explicit units in every algebraic substitution step.

  • Perform a sanity check on hydraulic displacements: a 1.60 μm1.60\text{ }\mu\text{m} output stroke cannot require a 4-meter (4000 mm4000\text{ mm}) input stroke on a micro-hydraulic actuator.

Lock it in

Similar question

01

A hydraulic car lift has an input piston of radius r1=1.0 cmr_1 = 1.0\text{ cm} and an output piston of radius r2=10.0 cmr_2 = 10.0\text{ cm}. What is the mechanical advantage of the lift, and how far must the input piston move to lift a car by 5.0 mm5.0\text{ mm}?

Answer

MA=100\text{MA} = 100; d1=500 mmd_1 = 500\text{ mm} (or 50 cm50\text{ cm}). Key steps: MA=(r2/r1)2=(10/1)2=100\text{MA} = (r_2/r_1)^2 = (10/1)^2 = 100. By volume conservation, d1=MA×d2=100×5.0 mm=500 mmd_1 = \text{MA} \times d_2 = 100 \times 5.0\text{ mm} = 500\text{ mm}.

02

A syringe with an internal barrel diameter of 16 mm16\text{ mm} is connected to a hypodermic needle with an inner diameter of 0.40 mm0.40\text{ mm}. If a nurse pushes the plunger with a force of 2.0 N2.0\text{ N}, what is the theoretical fluid force generated inside the needle bore, and what is the ratio of fluid speeds vneedle/vbarrelv_{\text{needle}}/v_{\text{barrel}}?

Answer

Fneedle=1.25×10−3 NF_{\text{needle}} = 1.25 \times 10^{-3}\text{ N}; vneedle/vbarrel=1600v_{\text{needle}}/v_{\text{barrel}} = 1600. Key steps: Diameter ratio D1/D2=16/0.40=40D_1/D_2 = 16/0.40 = 40. Area ratio A1/A2=402=1600A_1/A_2 = 40^2 = 1600. Pressure is uniform, so F2=F1/1600=2.0/1600=1.25×10−3 NF_2 = F_1 / 1600 = 2.0 / 1600 = 1.25 \times 10^{-3}\text{ N}. By continuity, v2/v1=A1/A2=1600v_2/v_1 = A_1/A_2 = 1600.

03

A two-stage hydraulic intensifier consists of a low-pressure cylinder of diameter da=60 mmd_a = 60\text{ mm} driving a high-pressure ram of diameter db=15 mmd_b = 15\text{ mm}. The high-pressure fluid from the ram then acts on a clamping piston of diameter dc=120 mmd_c = 120\text{ mm}. Find the overall mechanical advantage MAtotal=Fclamp/Finput\text{MA}_{\text{total}} = F_{\text{clamp}} / F_{\text{input}}.

Answer

MAtotal=1024\text{MA}_{\text{total}} = 1024. Key steps: Stage 1 connects pistons mechanically: Fa=FbF_a = F_b, so Pb=Pa(da/db)2=Pa(60/15)2=16PaP_b = P_a (d_a/d_b)^2 = P_a (60/15)^2 = 16 P_a. Stage 2 applies hydraulic pressure PbP_b to piston cc: Fc=PbAc=16PaAc=16FaAaAc=16(dc/da)2Fa=16×(120/60)2Fa=16×4Fa=64FaF_c = P_b A_c = 16 P_a A_c = 16 \frac{F_a}{A_a} A_c = 16 (d_c/d_a)^2 F_a = 16 \times (120/60)^2 F_a = 16 \times 4 F_a = 64 F_a... Wait, more directly: stage 1 transfers mechanical force directly (Fb=FaF_b = F_a), so intensifier output pressure is P2=Fa/AbP_2 = F_a / A_b. The clamping force is Fc=P2Ac=Fa(Ac/Ab)=Fa(dc/db)2=Fa(120/15)2=Fa(8)2=64FaF_c = P_2 A_c = F_a (A_c / A_b) = F_a (d_c / d_b)^2 = F_a (120/15)^2 = F_a (8)^2 = 64 F_a, giving MA=64\text{MA} = 64.

Loading workspace…