Resources
A heavy industrial container of mass rests on a rough horizontal concrete platform. The static coefficient of friction between the container and the concrete is . A hydraulic arm pushes downward and horizontally on the container with a force inclined at an angle below the horizontal (so that its components act horizontally in the direction and vertically downward in the direction). Take . (a) Formulate the static equilibrium threshold equations along the horizontal and vertical axes for the condition of impending slip. (b) Calculate the critical threshold magnitude of the pushing force required to initiate movement.
Answer and steps
Final answer
(a) , where ; (b) .
Steps
Part (a): Formulate the Static Equilibrium Threshold Equations
To find the condition for impending slip, we model the container as a particle in static equilibrium and resolve all acting forces into rectangular components.
-
Identify the forces acting on the container:
- Weight (): Directed vertically downward along the axis, with magnitude .
- Normal force (): Exerted upward by the floor along the axis.
- Applied pushing force (): Directed at an angle below the horizontal. Its components are:
- Maximum static friction force (): Opposes impending motion along the horizontal interface, directed in the direction, with magnitude:
- Vertical equilibrium (): The container does not accelerate vertically: Solving for the normal force: (Common Pitfall: Forgetting that pushing downward increases the normal force above the container's weight, which correspondingly increases the maximum available static friction.)
- Horizontal equilibrium at the threshold of motion (): At the point of impending slip, the horizontal pushing force balances the maximum static friction: where .
Part (b): Calculate the Critical Pushing Force Magnitude
- Substitute into the horizontal equilibrium equation:
- Rearrange and isolate :
-
Substitute the given numerical values:
Evaluating the denominator and numerator:
- Numerator:
- Denominator:
Typical errors
01 The student forgets that the downward component of the applied force increases the normal force, setting N = M * g instead.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
F_p \cos(30.0^) - f_s = 0 f_s = s N
- Step 2
N - M g = 0 N = M g
Correct\Sigma F_y = F_N - Mg - F_p \sin = 0 F_N = Mg + F_p \sin
Because the hydraulic arm pushes downward at an angle of below the horizontal, it exerts a downward vertical force component of . This presses the container harder into the concrete, increasing the normal force above the container's weight.
- Step 3
N = 85.0 9.80 = 833 F_p \cos(30.0^) = 0.420 833 F_p 0.866 = 349.86
CorrectF_p \cos(30.0^) - 0.420(Mg + F_p \sin(30.0^)) = 0 F_p(\cos(30.0^) - 0.420\sin(30.0^)) = 0.420 Mg
Because the normal force expression omitted the term, you treated as a constant rather than an expression dependent on .
- Step 4
F_{p,} = 349.86 / 0.866 = 404_
CorrectF_{p,} = 539_
This numerical result followed algebraically from your simplified normal force, but it does not account for the additional friction created by pushing downward.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly projected the pushing force along the horizontal axis as .
You correctly stated the threshold friction condition .
You carried out the subsequent arithmetic and division accurately according to your equations.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed the normal force always equals the object's weight (), forgetting to account for the vertical component of an angled external force when summing forces along the vertical axis.
REASONING PATH
Your ACEpath teacher’s suggested approach- Free-Body Diagram Component Check
Every angled force must be resolved into both horizontal and vertical components before writing and .
Draw the vertical component arrow alongside gravity to ensure it is included in .
- Variable Normal Force
When an applied force has a vertical component, the normal force depends on that applied force magnitude (), so friction also depends on .
Substitute the complete expression for into the friction equation and isolate algebraically before computing numerical values.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete vertical equilibrium condition: .
Substitute into the horizontal equilibrium equation: .
Group terms containing : .
Solve for .
Substitute values: .
02 The student treats the vertical component of the pushing force as directed upward, subtracting it from weight when determining the normal force.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the arm pushes downward at an angle below the horizontal, its vertical component acts in the direction alongside gravity, pressing the container harder against the floor.
- Step 3Correct
Your algebraic rearrangement was executed correctly based on your equation, but it inherited the sign error from the vertical force balance.
- Step 4Correct
Your arithmetic evaluation was mathematically sound, but the numerical answer is smaller than the true critical force due to the earlier vertical sign mistake.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the applied force into rectangular trigonometric components.
You correctly related the maximum available static friction to the normal force via .
You carried out algebraic isolation and arithmetic evaluation with strong consistency.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou assigned a positive sign to the vertical component of a force applied downward below the horizontal.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated an applied force angle without referencing the physical direction of the push: pushing downward adds to the compressive load against the supporting surface, increasing the normal force rather than relieving it.
REASONING PATH
Your ACEpath teacher’s suggested approach- Trace Vector Arrows Outward From the Object
On a free-body diagram, draw each contact force originating from the body's center of mass or surface and pointing in the direction of the physical push or pull.
When a force is directed 'below the horizontal', draw its vertical arrow pointing downward ().
- Perform a Physical Sanity Check on the Normal Force
Pushing downward on an object always increases the contact force (), whereas pulling upward relieves it ().
Check the sign of : downward applied forces must satisfy .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up vertical equilibrium with both weight and the vertical component acting downward: .
Substitute into the horizontal impending slip condition: .
Group terms on the left side: .
Isolate the critical force: .
Substitute values: .
03 The student swaps sine and cosine components for the horizontal and vertical forces with respect to the horizontal angle.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
F_p \sin(30.0^) F_p \cos(30.0^)
CorrectF_{px} = F_p \cos(30.0^) F_{py} = F_p \sin(30.0^)
The angle is given relative to the horizontal. Therefore, the horizontal component is adjacent to the angle () and the vertical component is opposite to the angle (). You reversed the sine and cosine assignments.
- Step 2
F_p \sin(30.0^) = s N N = M g + F_p \cos(30.0^)
Correct\Sigma F_x = F_p \cos(30.0^) - s F_N = 0 \Sigma F_y = F_N - M g - F_p \sin(30.0^) = 0
Your equilibrium structure is conceptually sound—correctly balancing horizontal thrust with maximum friction and recognizing that the downward push adds to the normal force—but this step is affected by the swapped trigonometric components from Step 1.
- Step 3
F_p \sin(30.0^) = s(M g + F_p \cos(30.0^)) F{p,} = = 2567
CorrectF_{p,} = = 539_
Your algebra and arithmetic correctly followed from your equations, but the numerical answer is incorrect due to the propagated trigonometric error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the downward component of the applied force increases the normal force above the object's weight.
You correctly formulated the condition of impending slip where the horizontal component balances maximum static friction .
You executed the multi-step algebraic isolation of accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated the horizontal component with sine and the vertical component with cosine instead of using the right-triangle definitions where the side adjacent to the specified horizontal reference angle requires cosine.
REASONING PATH
Your ACEpath teacher’s suggested approach- Reference Angle and Right Triangle
When an angle is measured with respect to the horizontal, the horizontal adjacent leg is and the vertical opposite leg is .
Always sketch a force triangle with the angle labeled at the horizontal axis before writing equations to visually confirm adjacent (cosine) versus opposite (sine).
CORRECTED PATH
ACEpath Teacher's DemonstrationDecompose the pushing force using the horizontal reference angle: and .
Formulate the vertical equilibrium equation: .
Formulate the horizontal equilibrium equation at impending slip: .
Substitute into the horizontal equation: .
Factor and isolate : .
Evaluate numerically: .
539 N
Lock it in
Does the normal force on a horizontal surface always equal the object's weight ?
No. Any vertical component of an applied force adds to or subtracts from the required normal force: .
Similar question
A crate rests on a horizontal floor with . A worker pushes downward and forward on the crate with a force at an angle of below the horizontal. What is the critical pushing force needed to start motion? Take .
Answer
. Using gives . At threshold, . Solving for : .
A sled of mass is on horizontal snow with . Instead of pushing, a rope pulls upward and forward at an angle of above the horizontal. Find the minimum tension required to start moving the sled. Take .
Answer
. Pulling upward reduces the normal force: . Horizontal equilibrium: . Rearranging yields .
A box of mass is pushed downward at angle below the horizontal on a floor with coefficient . (a) Determine the threshold force in terms of . (b) What happens to if ? Take .
Answer
(a) . (b) If (i.e., ), the denominator . The critical force becomes infinite or impossible, meaning no matter how hard the person pushes, the increase in static friction from the downward push matches or exceeds the additional forward driving force, completely jamming the box.