Resources

In an analytical chemistry laboratory, a peristaltic metering pump is calibrated by dispensing distilled water through narrow PEEK tubing (internal diameter d=0.500 mmd = 0.500\text{ mm}) into an analytical balance tared with a weighing vial. Over an elapsed time of Δt=5.00 minutes\Delta t = 5.00\text{ minutes}, the recorded mass of collected water is m=23.85 gm = 23.85\text{ g}. Given that the density of water at the measured laboratory temperature of 22.0∘C22.0^\circ\text{C} is ρ=0.9978 g/cm3\rho = 0.9978\text{ g/cm}^3, determine the experimental volumetric flow rate QQ in milliliters per minute (mL/min\text{mL/min}) and the mean linear flow velocity vv inside the tubing in meters per second (m/s\text{m/s}).

Answer and steps

Final answer

Q=4.78 mL/minQ = 4.78\text{ mL/min} (or 7.97×10−8 m3/s7.97 \times 10^{-8}\text{ m}^3\text{/s}), v=0.406 m/sv = 0.406\text{ m/s}

Steps

Step 1: Determine the Total Volume of Dispensed Water

The relationship between mass mm, density ρ\rho, and volume VV is given by:

V=mρV = \frac{m}{\rho}

Substitute the given mass m=23.85 gm = 23.85\text{ g} and density ρ=0.9978 g/cm3\rho = 0.9978\text{ g/cm}^3:

V=23.85 g0.9978 g/cm3≈23.903 cm3V = \frac{23.85\text{ g}}{0.9978\text{ g/cm}^3} \approx 23.903\text{ cm}^3

Since 1 cm3=1 mL1\text{ cm}^3 = 1\text{ mL}, the collected volume is:

V≈23.903 mLV \approx 23.903\text{ mL}


Step 2: Calculate the Volumetric Flow Rate (QQ)

The volumetric flow rate QQ is the volume of fluid passing through a cross-section per unit time:

Q=VΔtQ = \frac{V}{\Delta t}

Substitute V=23.903 mLV = 23.903\text{ mL} and Δt=5.00 min\Delta t = 5.00\text{ min}:

Q=23.903 mL5.00 min≈4.78 mL/minQ = \frac{23.903\text{ mL}}{5.00\text{ min}} \approx 4.78\text{ mL/min}

To prepare for finding the linear velocity in standard SI units (m/s\text{m/s}), convert QQ to cubic meters per second (m3/s\text{m}^3\text{/s}):

  • 1 mL=10−6 m31\text{ mL} = 10^{-6}\text{ m}^3
  • 1 min=60 s1\text{ min} = 60\text{ s}

Q=23.903×10−6 m35.00×60 s=23.903×10−6 m3300 s≈7.97×10−8 m3/sQ = \frac{23.903 \times 10^{-6}\text{ m}^3}{5.00 \times 60\text{ s}} = \frac{23.903 \times 10^{-6}\text{ m}^3}{300\text{ s}} \approx 7.97 \times 10^{-8}\text{ m}^3\text{/s}


Step 3: Calculate the Cross-Sectional Area of the Tubing (AA)

The tubing has a circular cross-section with an internal diameter d=0.500 mm=5.00×10−4 md = 0.500\text{ mm} = 5.00 \times 10^{-4}\text{ m}. The cross-sectional area AA is:

A=πd24=π⋅(5.00×10−4 m)24≈1.9635×10−7 m2A = \frac{\pi d^2}{4} = \frac{\pi \cdot (5.00 \times 10^{-4}\text{ m})^2}{4} \approx 1.9635 \times 10^{-7}\text{ m}^2


Step 4: Calculate the Mean Linear Flow Velocity (vv)

From the definition of volumetric flow rate, Q=A⋅vQ = A \cdot v, the mean flow velocity is:

v=QAv = \frac{Q}{A}

Substitute Q=7.968×10−8 m3/sQ = 7.968 \times 10^{-8}\text{ m}^3\text{/s} and A=1.9635×10−7 m2A = 1.9635 \times 10^{-7}\text{ m}^2:

v=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{7.968 \times 10^{-8}\text{ m}^3\text{/s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}

Common Pitfall: Ensure all variables are converted into matching base SI units (m3/s\text{m}^3\text{/s} and m2\text{m}^2) before dividing to find velocity in m/s\text{m/s}. Dividing flow rate in mL/min\text{mL/min} directly by an area in mm2\text{mm}^2 without proper unit factors is a frequent source of order-of-magnitude errors.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the diameter instead of the radius in the area formula, underestimating the cross-sectional area by a factor of 4 and resulting in an overestimated velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=23.850.9978=23.903 mLV = \frac{23.85}{0.9978} = 23.903\text{ mL}

  2. Step 2

    Q=23.9035.00=4.78 mL/min  ⟹  Q=4.7805×10−660=7.9675×10−8 m3/sQ = \frac{23.903}{5.00} = 4.78\text{ mL/min} \implies Q = \frac{4.7805 \times 10^{-6}}{60} = 7.9675 \times 10^{-8}\text{ m}^3/\text{s}

  3. Step 3

    A=π⋅d2=π⋅(0.000500)2=7.854×10−7 m2A = \pi \cdot d^2 = \pi \cdot (0.000500)^2 = 7.854 \times 10^{-7}\text{ m}^2

    Correct

    A=πd24=πr2=π(5.00×10−4 m)24≈1.9635×10−7 m2A = \frac{\pi d^2}{4} = \pi r^2 = \frac{\pi (5.00 \times 10^{-4}\text{ m})^2}{4} \approx 1.9635 \times 10^{-7}\text{ m}^2

    You wrote the circle area formula as πd2\pi d^2 rather than πd24\frac{\pi d^2}{4} (or πr2\pi r^2). Because the given dimension is the diameter d=0.500 mmd = 0.500\text{ mm}, the radius is r=d2=0.250 mmr = \frac{d}{2} = 0.250\text{ mm}, making the true cross-sectional area 4 times smaller.

  4. Step 4

    v=QA=7.9675×10−87.854×10−7=0.101 m/sv = \frac{Q}{A} = \frac{7.9675 \times 10^{-8}}{7.854 \times 10^{-7}} = 0.101\text{ m/s}

    Correct

    v=QA=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{Q}{A} = \frac{7.968 \times 10^{-8}\text{ m}^3/\text{s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}

    Your formula v=QAv = \frac{Q}{A} is correct, but dividing by the four-times-overestimated area propagated to give 0.101 m/s0.101\text{ m/s} instead of 0.406 m/s0.406\text{ m/s}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the collected liquid volume using mass and density.

You found the volumetric flow rate QQ and converted it to SI units with correct conversion factors.

You correctly identified that linear velocity relates to flow rate via v=QAv = \frac{Q}{A}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Substitution Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the diameter directly into the place of the radius in the area formula πr2\pi r^2, omitting the required division by 4 when expressing area in terms of diameter (A=πd24A = \frac{\pi d^2}{4}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Circular Cross-Section Formula
  • For a circle of diameter dd and radius r=d2r = \frac{d}{2}, the area is A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}.

  • Always write down r=d2r = \frac{d}{2} explicitly before calculating circular area, or use A=πd24A = \frac{\pi d^2}{4} whenever a problem gives internal diameter.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the tubing cross-sectional area using A=πd24=π(5.00×10−4 m)24≈1.9635×10−7 m2A = \frac{\pi d^2}{4} = \frac{\pi (5.00 \times 10^{-4}\text{ m})^2}{4} \approx 1.9635 \times 10^{-7}\text{ m}^2.

  2. Substitute the SI volumetric flow rate and corrected area into the velocity formula: v=QA=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{Q}{A} = \frac{7.968 \times 10^{-8}\text{ m}^3/\text{s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}.

Final answer

Q=4.78 mL/min,  v=0.406 m/sQ = 4.78\text{ mL/min},\; v = 0.406\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between expressing circle area via radius (A=πr2A = \pi r^2) versus diameter (A=πd24A = \frac{\pi d^2}{4}).

  • Practice converting cylindrical inner pipe diameters directly into cross-sectional areas across various microfluidic and fluid-flow contexts.

OverviewACEpath Teacher's Diagnosis

02 The student omits converting minutes to seconds when calculating velocity from volumetric flow rate, producing a velocity 60 times too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=23.85/0.9978=23.903 mLV = 23.85 / 0.9978 = 23.903\text{ mL}

  2. Step 2

    Q=23.903/5.00=4.78 mL/minQ = 23.903 / 5.00 = 4.78\text{ mL/min}

  3. Step 3

    A=π⋅(0.000250)2=1.9635×10−7 m2A = \pi \cdot (0.000250)^2 = 1.9635 \times 10^{-7}\text{ m}^2

  4. Step 4

    Q=4.7805×10−6 m3/min  ⟹  v=QA=4.7805×10−61.9635×10−7=24.3 m/sQ = 4.7805 \times 10^{-6}\text{ m}^3\text{/min} \implies v = \frac{Q}{A} = \frac{4.7805 \times 10^{-6}}{1.9635 \times 10^{-7}} = 24.3\text{ m/s}

    Correct

    Q=4.7805×10−6 m360 s≈7.968×10−8 m3/s  ⟹  v=QA=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sQ = \frac{4.7805 \times 10^{-6}\text{ m}^3}{60\text{ s}} \approx 7.968 \times 10^{-8}\text{ m}^3\text{/s} \implies v = \frac{Q}{A} = \frac{7.968 \times 10^{-8}\text{ m}^3\text{/s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}

    You converted volume from milliliters to cubic meters, but kept time in minutes. Dividing m3/min\text{m}^3\text{/min} by m2\text{m}^2 gives linear velocity in m/min\text{m/min}, not m/s\text{m/s}. To get velocity in meters per second, divide the flow rate by 60 s/min60\text{ s/min} before dividing by the area.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the fluid density to convert mass to volume.

You calculated the volumetric flow rate accurately in mL/min\text{mL/min}.

You correctly computed the cross-sectional area of the narrow tubing in square meters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion error (time base mismatch)

You converted the volume unit from mL\text{mL} to m3\text{m}^3 but omitted converting minutes to seconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating mixed units as coherent SI base units without explicitly carrying unit labels through the calculation of linear velocity.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Base SI Units for Flow Rate
  • 1 mL/min=10−6 m360 s=160×10−6 m3/s1\text{ mL/min} = \frac{10^{-6}\text{ m}^3}{60\text{ s}} = \frac{1}{60} \times 10^{-6}\text{ m}^3\text{/s}

  • Whenever you calculate velocity v=Q/Av = Q/A in m/s\text{m/s}, ensure that flow rate QQ is fully converted to m3/s\text{m}^3\text{/s} before dividing by area in m2\text{m}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert volumetric flow rate from m3/min\text{m}^3\text{/min} to standard SI units (m3/s\text{m}^3\text{/s}): Q=4.7805×10−6 m360 s≈7.968×10−8 m3/sQ = \frac{4.7805 \times 10^{-6}\text{ m}^3}{60\text{ s}} \approx 7.968 \times 10^{-8}\text{ m}^3\text{/s}.

  2. Divide by cross-sectional area A=1.9635×10−7 m2A = 1.9635 \times 10^{-7}\text{ m}^2: v=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{7.968 \times 10^{-8}\text{ m}^3\text{/s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}.

Final answer

Q=4.78 mL/minQ = 4.78\text{ mL/min} and v=0.406 m/sv = 0.406\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Include explicit physical units at each step of your algebra rather than writing bare numbers.

  • Perform a sanity check on velocity: 24.3 m/s24.3\text{ m/s} is about 87 km/h87\text{ km/h}, which is far too fast for a micro-dispensing lab pump.

OverviewACEpath Teacher's Diagnosis

03 The student assumes water density is exactly 1.00 g/cm³ instead of using the provided temperature-dependent density, leading to an inaccurate volume and flow rate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=23.85/1.00=23.85 mLV = 23.85 / 1.00 = 23.85\text{ mL}

    Correct

    V=mρ=23.85 g0.9978 g/cm3≈23.903 cm3=23.903 mLV = \frac{m}{\rho} = \frac{23.85\text{ g}}{0.9978\text{ g/cm}^3} \approx 23.903\text{ cm}^3 = 23.903\text{ mL}

    You used the approximate standard density 1.00 g/cm31.00\text{ g/cm}^3 instead of the exact laboratory value ρ=0.9978 g/cm3\rho = 0.9978\text{ g/cm}^3 given at 22.0∘C22.0^\circ\text{C}.

  2. Step 2

    Q=23.85/5.00=4.77 mL/minQ = 23.85 / 5.00 = 4.77\text{ mL/min}

    Correct

    Q=23.903 mL5.00 min≈4.78 mL/minQ = \frac{23.903\text{ mL}}{5.00\text{ min}} \approx 4.78\text{ mL/min}

    Your formula and division are correct, but this value is affected by your earlier volume calculation.

  3. Step 3

    A=π⋅(0.000250)2=1.9635×10−7 m2A = \pi \cdot (0.000250)^2 = 1.9635 \times 10^{-7}\text{ m}^2

  4. Step 4

    Q=(4.77×10−6)/60=7.95×10−8 m3/sQ = (4.77 \times 10^{-6}) / 60 = 7.95 \times 10^{-8}\text{ m}^3/\text{s}

    Correct

    Q=4.7806×10−6 m360 s≈7.97×10−8 m3/sQ = \frac{4.7806 \times 10^{-6}\text{ m}^3}{60\text{ s}} \approx 7.97 \times 10^{-8}\text{ m}^3/\text{s}

    Your unit conversion method from mL/min\text{mL/min} to m3/s\text{m}^3/\text{s} is entirely correct, though carrying through the previous rounded value gives 7.95×10−8 m3/s7.95 \times 10^{-8}\text{ m}^3/\text{s} instead of 7.97×10−8 m3/s7.97 \times 10^{-8}\text{ m}^3/\text{s}.

  5. Step 5

    v=QA=7.95×10−81.9635×10−7=0.405 m/sv = \frac{Q}{A} = \frac{7.95 \times 10^{-8}}{1.9635 \times 10^{-7}} = 0.405\text{ m/s}

    Correct

    v=QA=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{Q}{A} = \frac{7.968 \times 10^{-8}\text{ m}^3/\text{s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}

    You applied the continuity relationship v=QAv = \frac{Q}{A} correctly, but the result reflects the propagated density discrepancy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related volumetric flow rate to linear velocity via Q=A⋅vQ = A \cdot v.

You converted units between mL/min\text{mL/min} and m3/s\text{m}^3/\text{s} accurately.

You calculated the circular cross-sectional area using the correct radius in SI units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Density Value Assumption

You substituted an assumed density of 1.00 g/cm31.00\text{ g/cm}^3 instead of the exact laboratory value ρ=0.9978 g/cm3\rho = 0.9978\text{ g/cm}^3 stated in the problem.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In high-precision calibration problems, physical parameters such as density vary with temperature. Relying on default mental constants rather than checking provided conditions introduces systematic errors in analytical calculations.

REASONING PATH
Your ACEpath teacher’s suggested approach
Temperature-Dependent Properties
  • Always use the explicitly provided fluid density rather than the nominal standard density of 1.00 g/cm31.00\text{ g/cm}^3.

  • Scan the problem statement for temperature and corresponding fluid density before converting measured mass into volume.

Consistent SI Base Units
  • Linear flow velocity requires volumetric flow in m3/s\text{m}^3/\text{s} and area in m2\text{m}^2.

  • Multiply mL\text{mL} by 10−6 m3/mL10^{-6}\text{ m}^3/\text{mL} and divide minutes by 60 s/min60\text{ s/min} before solving for velocity.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. V=mρ=23.85 g0.9978 g/cm3≈23.903 cm3=23.903 mLV = \frac{m}{\rho} = \frac{23.85\text{ g}}{0.9978\text{ g/cm}^3} \approx 23.903\text{ cm}^3 = 23.903\text{ mL}

  2. Q=23.903 mL5.00 min=4.78 mL/minQ = \frac{23.903\text{ mL}}{5.00\text{ min}} = 4.78\text{ mL/min}

  3. Q=23.903×10−6 m3300 s≈7.968×10−8 m3/sQ = \frac{23.903 \times 10^{-6}\text{ m}^3}{300\text{ s}} \approx 7.968 \times 10^{-8}\text{ m}^3/\text{s}

  4. v=QA=7.968×10−8 m3/s1.9635×10−7 m2≈0.406 m/sv = \frac{Q}{A} = \frac{7.968 \times 10^{-8}\text{ m}^3/\text{s}}{1.9635 \times 10^{-7}\text{ m}^2} \approx 0.406\text{ m/s}

Final answer

Q=4.78 mL/minQ = 4.78\text{ mL/min}, v=0.406 m/sv = 0.406\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review problem statements carefully for temperature-adjusted physical constants before beginning calculations.

  • Practice distinguishing nominal textbook approximations from calibrated experimental parameters.

  • Keep intermediate values unrounded in your calculator to avoid cumulative rounding discrepancies.

Lock it in

Similar question

01

A syringe pump dispenses fluid through a needle with inner diameter d=0.40 mmd = 0.40\text{ mm} at a steady rate of Q=1.20 mL/minQ = 1.20\text{ mL/min}. Calculate the mean flow velocity vv inside the needle in m/s\text{m/s}.

Answer

v=0.159 m/sv = 0.159\text{ m/s}. Convert Q=1.20×10−6 m3/60 s=2.00×10−8 m3/sQ = 1.20 \times 10^{-6}\text{ m}^3 / 60\text{ s} = 2.00 \times 10^{-8}\text{ m}^3/\text{s}. The area is A=π(4.0×10−4 m)24=1.257×10−7 m2A = \frac{\pi (4.0 \times 10^{-4}\text{ m})^2}{4} = 1.257 \times 10^{-7}\text{ m}^2. Thus, v=QA=2.00×10−81.257×10−7≈0.159 m/sv = \frac{Q}{A} = \frac{2.00 \times 10^{-8}}{1.257 \times 10^{-7}} \approx 0.159\text{ m/s}.

02

Water flows through a horizontal pipe of diameter d1=4.0 cmd_1 = 4.0\text{ cm} at a speed of v1=1.5 m/sv_1 = 1.5\text{ m/s}. The pipe narrows to a nozzle with diameter d2=1.0 cmd_2 = 1.0\text{ cm}. Find the volumetric flow rate QQ in L/s\text{L/s} and the exit velocity v2v_2 in m/s\text{m/s}.

Answer

Q=1.88 L/sQ = 1.88\text{ L/s}, v2=24.0 m/sv_2 = 24.0\text{ m/s}. Cross-sectional area A1=π(0.040 m)24=1.257×10−3 m2A_1 = \frac{\pi (0.040\text{ m})^2}{4} = 1.257 \times 10^{-3}\text{ m}^2. Flow rate Q=A1v1=(1.257×10−3 m2)(1.5 m/s)=1.885×10−3 m3/s=1.88 L/sQ = A_1 v_1 = (1.257 \times 10^{-3}\text{ m}^2)(1.5\text{ m/s}) = 1.885 \times 10^{-3}\text{ m}^3/\text{s} = 1.88\text{ L/s}. By continuity, v2=v1(d1d2)2=1.5×42=24.0 m/sv_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 1.5 \times 4^2 = 24.0\text{ m/s}.

03

An oil of density ρ=850 kg/m3\rho = 850\text{ kg/m}^3 flows steadily through an industrial tubing system. A collection vessel records m=10.2 kgm = 10.2\text{ kg} of oil over Δt=2.00 minutes\Delta t = 2.00\text{ minutes}. If the mean flow velocity inside the tubing must not exceed vmax=0.800 m/sv_{\text{max}} = 0.800\text{ m/s}, what is the minimum required internal diameter dmind_{\text{min}} of the tubing in millimeters?

Answer

dmin=12.6 mmd_{\text{min}} = 12.6\text{ mm}. Volume collected is V=mρ=10.2850=0.012 m3V = \frac{m}{\rho} = \frac{10.2}{850} = 0.012\text{ m}^3. Flow rate Q=0.012 m3120 s=1.00×10−4 m3/sQ = \frac{0.012\text{ m}^3}{120\text{ s}} = 1.00 \times 10^{-4}\text{ m}^3/\text{s}. Minimum area is Amin=Qvmax=1.00×10−40.800=1.25×10−4 m2A_{\text{min}} = \frac{Q}{v_{\text{max}}} = \frac{1.00 \times 10^{-4}}{0.800} = 1.25 \times 10^{-4}\text{ m}^2. Then dmin=4Aminπ=4×1.25×10−4π≈0.0126 m=12.6 mmd_{\text{min}} = \sqrt{\frac{4 A_{\text{min}}}{\pi}} = \sqrt{\frac{4 \times 1.25 \times 10^{-4}}{\pi}} \approx 0.0126\text{ m} = 12.6\text{ mm}.

Loading workspace…