Resources

A block of mass m=1.50 kgm = 1.50\text{ kg} is launched across a level floor with an initial kinetic energy Ek=45.0 JE_k = 45.0\text{ J} directly toward an uncompressed spring with stiffness k=320 N/mk = 320\text{ N/m}. The surface between the launch point and the spring has length D=2.00 mD = 2.00\text{ m}. To prevent the block from coming to a complete stop before touching the spring, what is the maximum allowable value for the coefficient of kinetic friction μk,max\mu_{k,\text{max}} of the floor? Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

μk,max=1.53\mu_{k,\text{max}} = 1.53

Steps

01

Identify the Physical Condition

For the block to reach the uncompressed spring without stopping beforehand, its kinetic energy upon touching the spring must be greater than zero. At the limiting case, the block stops just as it makes contact with the spring:

Ek,final≥0E_{k,\text{final}} \ge 0

Note that the spring constant kk is extraneous for this specific condition, as the block has not yet compressed the spring.


02

Relate the Work Done by Friction to Kinetic Energy

As the block slides along the horizontal floor over the distance DD:

  • The vertical forces are balanced: the normal force is N=mgN = mg.
  • The magnitude of the kinetic friction force is: fk=μkN=μkmgf_k = \mu_k N = \mu_k mg
  • The work done by friction over the displacement DD opposes the motion: Wf=−fkD=−μkmgDW_f = -f_k D = -\mu_k mg D

According to the Work-Energy Theorem:

Ek,final−Ek=Wf=−μkmgDE_{k,\text{final}} - E_k = W_f = -\mu_k mg D

Ek,final=Ek−μkmgDE_{k,\text{final}} = E_k - \mu_k mg D


03

Solve for the Maximum Coefficient of Kinetic Friction

To prevent the block from stopping before it reaches the spring, we require:

Ek−μkmgD≥0  ⟹  μk≤EkmgDE_k - \mu_k mg D \ge 0 \implies \mu_k \le \frac{E_k}{mgD}

Thus, the maximum allowable value μk,max\mu_{k,\text{max}} corresponds to the equality:

μk,max=EkmgD\mu_{k,\text{max}} = \frac{E_k}{mgD}


04

Substitute Numerical Values

Substitute Ek=45.0 JE_k = 45.0\text{ J}, m=1.50 kgm = 1.50\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, and D=2.00 mD = 2.00\text{ m}:

μk,max=45.0(1.50)(9.80)(2.00)=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{(1.50)(9.80)(2.00)} = \frac{45.0}{29.4} \approx 1.53

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student includes the spring potential energy even though the block only needs to reach the uncompressed spring before stopping.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ek=Wf+(12)⋅k⋅x2  ⟹  Ek=μk⋅m⋅g⋅D+(12)⋅k⋅D2E_k = W_f + \left(\frac{1}{2}\right) \cdot k \cdot x^2 \implies E_k = \mu_k \cdot m \cdot g \cdot D + \left(\frac{1}{2}\right) \cdot k \cdot D^2

    Correct

    Ek−Wf≥0  ⟹  Ek=μkmgDE_k - W_f \ge 0 \implies E_k = \mu_k m g D

    The block only needs to reach the spring without stopping beforehand. At the moment it touches the spring, the spring is not yet compressed (x=0x = 0), so no elastic potential energy is stored in the spring. Furthermore, setting the spring compression xx equal to the floor length DD incorrectly conflates the travel distance before contact with the spring deformation.

  2. Step 2

    45.0=μk⋅(1.50)(9.80)(2.00)+0.5⋅(320)(2.00)2  ⟹  45.0=29.4⋅μk+64045.0 = \mu_k \cdot (1.50)(9.80)(2.00) + 0.5 \cdot (320)(2.00)^2 \implies 45.0 = 29.4 \cdot \mu_k + 640

    Correct

    45.0=μk⋅(1.50)(9.80)(2.00)  ⟹  45.0=29.4μk45.0 = \mu_k \cdot (1.50)(9.80)(2.00) \implies 45.0 = 29.4 \mu_k

    You substituted the numerical values correctly into your equation, but the step inherits the extraneous 640 J640\text{ J} spring energy term from Step 1.

  3. Step 3

    μk=45.0−64029.4=−20.2\mu_k = \frac{45.0 - 640}{29.4} = -20.2

    Correct

    μk,max=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{29.4} \approx 1.53

    Your algebra is executed correctly from your previous equation, but the resulting negative coefficient reflects the error introduced in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the work done by kinetic friction as Wf=μkmgDW_f = \mu_k m g D.

You correctly solved the resulting linear algebraic equation for μk\mu_k.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Extraneous spring potential energy

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You included spring potential energy in the energy conservation equation even though the problem specifies that the block only needs to reach and touch the uncompressed spring, meaning the spring compression is zero (x=0x = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Initial and Final States
  • Only include energy terms corresponding to the actual deformation or configuration at the chosen boundary states.

  • Check whether the spring is compressed at the target instant. If the block just reaches the uncompressed spring, x=0x = 0 and Us=0U_s = 0.

Physical Reality Check
  • The coefficient of kinetic friction μk\mu_k between ordinary surfaces must always be non-negative.

  • If you obtain a negative friction coefficient, pause and re-check whether an unnecessary energy sink or source was introduced into the equation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. At the limiting condition, the block reaches the spring with zero remaining kinetic energy: Ek,final=Ek−fkD=0E_{k,\text{final}} = E_k - f_k D = 0.

  2. Set the initial kinetic energy equal to the work done against friction over distance DD: Ek=μk,maxmgDE_k = \mu_{k,\text{max}} m g D.

  3. Substitute the given numbers: 45.0=μk,max(1.50)(9.80)(2.00)=29.4μk,max45.0 = \mu_{k,\text{max}} (1.50)(9.80)(2.00) = 29.4 \mu_{k,\text{max}}.

  4. Solve for the maximum coefficient: μk,max=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{29.4} \approx 1.53.

Final answer

μk,max=1.53\mu_{k,\text{max}} = 1.53

NEXT STEPS
Final Takeaways from Your Teacher
  • Carefully reread boundary conditions such as 'before touching the spring' to identify which components are active.

  • Practice distinguishing between travel distance across a surface and compression distance of an elastic element.

OverviewACEpath Teacher's Diagnosis

02 The student omits the acceleration due to gravity g when calculating the frictional force, equating normal force directly to mass.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    fk=μk⋅mf_k = \mu_k \cdot m

    Correct

    fk=μkN=μkmgf_k = \mu_k N = \mu_k m g

    You defined the kinetic friction force using mass instead of weight or normal force. On a flat horizontal surface, the normal force is N=mgN = mg, making the friction force fk=μkmgf_k = \mu_k mg.

  2. Step 2

    Wf=μk⋅m⋅D  ⟹  Ek=μk⋅m⋅DW_f = \mu_k \cdot m \cdot D \implies E_k = \mu_k \cdot m \cdot D

    Correct

    Wf=fkD=μkmgD  ⟹  Ek=μkmgDW_f = f_k D = \mu_k m g D \implies E_k = \mu_k m g D

    You correctly recognized that the block stops right before the spring when the work dissipated by friction equals the initial kinetic energy, but this relation inherited the missing factor of gg from Step 1.

  3. Step 3

    45.0=μk⋅(1.50)⋅(2.00)  ⟹  μk=45.0/3.00=15.045.0 = \mu_k \cdot (1.50) \cdot (2.00) \implies \mu_k = 45.0 / 3.00 = 15.0

    Correct

    45.0=μk⋅(1.50)(9.80)(2.00)  ⟹  μk,max=45.029.4≈1.5345.0 = \mu_k \cdot (1.50)(9.80)(2.00) \implies \mu_{k,\text{max}} = \frac{45.0}{29.4} \approx 1.53

    Your arithmetic was carried out accurately based on your expression, but the final numerical value is off by a factor of gg (9.80 m/s29.80\text{ m/s}^2).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the limiting condition occurs when all initial kinetic energy is dissipated by friction over distance DD.

You recognized that the spring constant is not needed before the block reaches the spring.

You solved the resulting linear algebraic equation cleanly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of gravitational acceleration in normal force

You wrote fk=μkmf_k = \mu_k m instead of fk=μkmgf_k = \mu_k mg, leaving out the acceleration due to gravity gg.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing mass mm (measured in kilograms) with normal force NN or weight W=mgW = mg (measured in newtons) when computing friction.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimension and Units Check
  • Friction force must have units of newtons (N=kg⋅m/s2\text{N} = \text{kg}\cdot\text{m/s}^2). Since the coefficient of friction μ\mu is dimensionless, the product μm\mu m only has units of kg\text{kg}, which is not a force.

  • Always multiply mass by gravitational acceleration gg to get the normal force N=mgN = mg on a horizontal surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the normal force on a horizontal floor: N=mg=(1.50 kg)(9.80 m/s2)=14.7 NN = mg = (1.50\text{ kg})(9.80\text{ m/s}^2) = 14.7\text{ N}.

  2. Express friction force correctly: fk=μkN=μkmgf_k = \mu_k N = \mu_k mg.

  3. Set the maximum work done by friction equal to the initial kinetic energy: μk,maxmgD=Ek\mu_{k,\text{max}} mg D = E_k.

  4. Substitute the given numbers: μk,max=45.0(1.50)(9.80)(2.00)=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{(1.50)(9.80)(2.00)} = \frac{45.0}{29.4} \approx 1.53.

Final answer

μk,max≈1.53\mu_{k,\text{max}} \approx 1.53

NEXT STEPS
Final Takeaways from Your Teacher
  • Perform a quick dimensional check whenever you write a force formula to ensure the expression yields units of newtons.

  • Draw a quick free-body diagram showing NN balancing mgmg vertically before substituting into fk=μkNf_k = \mu_k N.

OverviewACEpath Teacher's Diagnosis

03 The student misinterprets the given kinetic energy value as initial velocity v_0 and recalculates kinetic energy as (1/2) · m · (45.0)².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ek=12⋅m⋅v2=0.5⋅(1.50)⋅(45.0)2=1518.75 JE_k = \frac{1}{2} \cdot m \cdot v^2 = 0.5 \cdot (1.50) \cdot (45.0)^2 = 1518.75\text{ J}

    Correct

    Ek=45.0 JE_k = 45.0\text{ J}

    The problem directly provided the initial kinetic energy as Ek=45.0 JE_k = 45.0\text{ J}. You substituted 45.045.0 in place of velocity vv into 12mv2\frac{1}{2}mv^2, which inflated the energy value.

  2. Step 2

    Wf=μk⋅m⋅g⋅D=Ek  ⟹  μk⋅(1.50)⋅(9.80)⋅(2.00)=1518.75  ⟹  29.4⋅μk=1518.75W_f = \mu_k \cdot m \cdot g \cdot D = E_k \implies \mu_k \cdot (1.50) \cdot (9.80) \cdot (2.00) = 1518.75 \implies 29.4 \cdot \mu_k = 1518.75

    Correct

    μk⋅(1.50)(9.80)(2.00)=45.0  ⟹  29.4μk=45.0\mu_k \cdot (1.50)(9.80)(2.00) = 45.0 \implies 29.4\mu_k = 45.0

    You correctly identified that the work done by friction over distance DD must equal the initial kinetic energy at the stopping limit, but this step inherited the incorrect energy value from Step 1.

  3. Step 3

    μk=1518.7529.4≈51.7\mu_k = \frac{1518.75}{29.4} \approx 51.7

    Correct

    μk,max=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{29.4} \approx 1.53

    You solved the linear equation correctly, but because the numerator was inflated, the resulting friction coefficient is much too large.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the work done by friction as Wf=μkmgDW_f = \mu_k m g D.

You accurately applied the work-energy theorem to set the friction work equal to the initial kinetic energy for the limiting stopping condition.

You executed the algebraic division accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Variable Misinterpretation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused a given energy quantity (Ek=45.0 JE_k = 45.0\text{ J}) with a kinematic velocity (v=45.0 m/sv = 45.0\text{ m/s}) and redundantly evaluated 12mv2\frac{1}{2}mv^2, which produced an unphysically high friction coefficient of 51.751.7.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Given Units Before Calculating
  • Always verify the unit of each given numerical value ([J][\text{J}] denotes energy, while [m/s][\text{m/s}] denotes speed or velocity).

  • If a quantity is already given in joules (J\text{J}), use it directly as energy rather than substituting it into 12mv2\frac{1}{2}mv^2.

Sanity-Check Friction Coefficients
  • Typical kinetic friction coefficients μk\mu_k in introductory physics problems range between 00 and 22.

  • If your calculated μk\mu_k is an extreme outlier such as 51.751.7, pause and check whether you squared an already-computed energy or mixed up units.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the work done by friction equal to the directly given initial kinetic energy: μkmgD=Ek\mu_k m g D = E_k.

  2. Substitute the given values: μk(1.50 kg)(9.80 m/s2)(2.00 m)=45.0 J\mu_k (1.50\text{ kg})(9.80\text{ m/s}^2)(2.00\text{ m}) = 45.0\text{ J}.

  3. Simplify the left side: 29.4μk=45.029.4\mu_k = 45.0.

  4. Solve for the maximum coefficient: μk,max=45.029.4≈1.53\mu_{k,\text{max}} = \frac{45.0}{29.4} \approx 1.53.

Final answer

μk,max≈1.53\mu_{k,\text{max}} \approx 1.53

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the given problem statement to distinguish directly stated energies from velocities based on their units.

  • Redo the final division using Ek=45.0 JE_k = 45.0\text{ J} to confirm the allowable friction coefficient μk,max≈1.53\mu_{k,\text{max}} \approx 1.53.

Lock it in

Similar question

01

A 2.0 kg2.0\text{ kg} box slides across a rough horizontal floor with an initial speed of 4.0 m/s4.0\text{ m/s}. It travels a distance D=5.0 mD = 5.0\text{ m} to just reach an uncompressed bumper spring (k=500 N/mk = 500\text{ N/m}) before stopping. What is the coefficient of kinetic friction μk\mu_k? Take g=9.8 m/s2g = 9.8\text{ m/s}^2.

Answer

μk≈0.163\mu_k \approx 0.163. Key steps: Initial kinetic energy Ek=12mv2=12(2.0)(4.0)2=16 JE_k = \frac{1}{2}mv^2 = \frac{1}{2}(2.0)(4.0)^2 = 16\text{ J}. Work against friction is Wf=μkmgD=μk(2.0)(9.8)(5.0)=98μkW_f = \mu_k m g D = \mu_k(2.0)(9.8)(5.0) = 98\mu_k. Since the spring is not compressed, Ek=Wf  ⟹  16=98μk  ⟹  μk=1698≈0.163E_k = W_f \implies 16 = 98\mu_k \implies \mu_k = \frac{16}{98} \approx 0.163.

02

A 0.50 kg0.50\text{ kg} puck with initial kinetic energy 12.0 J12.0\text{ J} travels across a rough floor of length D=3.0 mD = 3.0\text{ m} (where μk=0.40\mu_k = 0.40) and then contacts a horizontal spring with k=200 N/mk = 200\text{ N/m}. Does the puck reach the spring? If so, what is its maximum compression xx? Take g=9.8 m/s2g = 9.8\text{ m/s}^2.

Answer

Yes, it reaches the spring and compresses it by x≈0.25 mx \approx 0.25\text{ m}. Key steps: Energy lost to friction before touching the spring is Wf1=μkmgD=(0.40)(0.50)(9.8)(3.0)=5.88 JW_{f1} = \mu_k m g D = (0.40)(0.50)(9.8)(3.0) = 5.88\text{ J}. Since 12.0 J>5.88 J12.0\text{ J} > 5.88\text{ J}, the puck reaches the spring with Ek1=12.0−5.88=6.12 JE_{k1} = 12.0 - 5.88 = 6.12\text{ J}. Assuming the floor beneath the spring is smooth, 12kx2=6.12  ⟹  x=2(6.12)200≈0.247 m\frac{1}{2}kx^2 = 6.12 \implies x = \sqrt{\frac{2(6.12)}{200}} \approx 0.247\text{ m}.

03

A mass mm is projected with speed v0v_0 toward a spring located a distance DD away on a floor where the coefficient of friction is μk\mu_k. Derive the inequality that v0v_0 must satisfy so that the mass makes contact with the spring before coming to rest.

Answer

v0>2μkgDv_0 > \sqrt{2\mu_k g D}. Key steps: The work done by friction over distance DD is Wf=μkmgDW_f = \mu_k m g D. For the mass to reach the spring without stopping, final kinetic energy at contact must be strictly positive: 12mv02−μkmgD>0  ⟹  v02>2μkgD  ⟹  v0>2μkgD\frac{1}{2}mv_0^2 - \mu_k m g D > 0 \implies v_0^2 > 2\mu_k g D \implies v_0 > \sqrt{2\mu_k g D}.

Loading workspace…