Resources

A horizontal bimetallic strip of length L0=15.0 cmL_0 = 15.0\text{ cm} at T0=25.0∘CT_0 = 25.0^\circ\text{C} consists of two thin, equal-thickness strips bonded securely face-to-face: strip A is brass (αA=1.90×10−5 ∘C−1\alpha_A = 1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1}) on top, and strip B is Invar (αB=1.20×10−6 ∘C−1\alpha_B = 1.20 \times 10^{-6}\text{ }^\circ\text{C}^{-1}) on the bottom. The strip is clamped rigidly at its left end (x=0x = 0) such that the tangent is horizontal. (a) If the strip is cooled to T1=−15.0∘CT_1 = -15.0^\circ\text{C}, state whether the free tip deflects upward or downward along the vertical yy-axis, justifying with the sign of the differential thermal strain Δϵ=ΔLA/L0−ΔLB/L0\Delta \epsilon = \Delta L_A/L_0 - \Delta L_B/L_0. (b) Calculate the numerical difference in free-expansion linear change (ΔLA−ΔLB)(\Delta L_A - \Delta L_B) at T1=−15.0∘CT_1 = -15.0^\circ\text{C}.

Answer and steps

Final answer

(a) Upward deflection (Δϵ=−7.12×10−4<0\Delta \epsilon = -7.12 \times 10^{-4} < 0, brass contracts more than Invar on top, curling the strip convex downward and tipping upward); (b) ΔLA−ΔLB=−1.07×10−4 m=−0.107 mm\Delta L_A - \Delta L_B = -1.07 \times 10^{-4}\text{ m} = -0.107\text{ mm}

Steps

Part (a): Determining the Direction of Deflection

  1. Calculate the temperature change (ΔT\Delta T): The strip is cooled from T0=25.0∘CT_0 = 25.0^\circ\text{C} to T1=−15.0∘CT_1 = -15.0^\circ\text{C}: ΔT=T1−T0=−15.0∘C−25.0∘C=−40.0∘C\Delta T = T_1 - T_0 = -15.0^\circ\text{C} - 25.0^\circ\text{C} = -40.0^\circ\text{C}
  2. Evaluate the differential thermal strain (Δϵ\Delta \epsilon): Free thermal strain for each material is given by ϵ=αΔT\epsilon = \alpha \Delta T. Therefore, the differential strain between the top layer (brass, AA) and the bottom layer (Invar, BB) is: Δϵ=ΔLAL0−ΔLBL0=(αA−αB)ΔT\Delta \epsilon = \frac{\Delta L_A}{L_0} - \frac{\Delta L_B}{L_0} = (\alpha_A - \alpha_B)\Delta T

    Substitute the given coefficients of linear expansion: αA−αB=1.90×10−5 ∘C−1−1.20×10−6 ∘C−1=1.78×10−5 ∘C−1\alpha_A - \alpha_B = 1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1} - 1.20 \times 10^{-6}\text{ }^\circ\text{C}^{-1} = 1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1} Δϵ=(1.78×10−5 ∘C−1)(−40.0∘C)=−7.12×10−4\Delta \epsilon = (1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -7.12 \times 10^{-4}

  3. Determine the bending direction:

    • Because Δϵ<0\Delta \epsilon < 0, the top layer (brass) contracts more than the bottom layer (Invar).
    • In a bonded bimetallic beam, the layer that undergoes greater contraction is placed in tension and forms the inner (concave) arc of the curve.
    • Since the top layer becomes shorter, the concave side faces upward, causing the strip to curl upward. With the left end fixed horizontally, the free tip deflects upward along the positive yy-axis.

Part (b): Calculating the Difference in Free Linear Expansion

  1. Relate linear change to initial length and differential strain: ΔLA−ΔLB=L0Δϵ\Delta L_A - \Delta L_B = L_0 \Delta \epsilon
  2. Substitute L0=15.0 cm=0.150 mL_0 = 15.0\text{ cm} = 0.150\text{ m}: ΔLA−ΔLB=(0.150 m)(−7.12×10−4)=−1.068×10−4 m\Delta L_A - \Delta L_B = (0.150\text{ m})(-7.12 \times 10^{-4}) = -1.068 \times 10^{-4}\text{ m}
  3. Round to three significant figures: ΔLA−ΔLB≈−1.07×10−4 m=−0.107 mm\Delta L_A - \Delta L_B \approx -1.07 \times 10^{-4}\text{ m} = -0.107\text{ mm}

(Common Pitfall: Confusing cooling with heating. Upon heating (ΔT>0\Delta T > 0), brass expands more, forcing the strip to bend downward. Upon cooling (ΔT<0\Delta T < 0), brass contracts more, forcing the strip to curl upward.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student associates higher expansion coefficient with curving away from that side even during cooling, mistakenly concluding the strip bends downward.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=−15.0∘C−25.0∘C=−40.0∘C  ⟹  Δϵ=(αA−αB)ΔT=(1.90×10−5−1.20×10−6)(−40.0)<0\Delta T = -15.0^\circ\text{C} - 25.0^\circ\text{C} = -40.0^\circ\text{C} \implies \Delta \epsilon = (\alpha_A - \alpha_B)\Delta T = (1.90 \times 10^{-5} - 1.20 \times 10^{-6})(-40.0) < 0

  2. Step 2

    Brass has larger \text{Brass has larger } α\alpha  and is on top, so the strip bends away from brass, deflecting downward.\text{ and is on top, so the strip bends away from brass, deflecting downward.}

    Correct

    Because \text{Because } Δ\Delta ϵ\epsilon < 0, brass contracts more than Invar, so the top layer becomes shorter and forms the inner (concave) curve, deflecting upward.\text{, brass contracts more than Invar, so the top layer becomes shorter and forms the inner (concave) curve, deflecting upward.}

    A strip bends away from the larger-α\alpha material only when heated. Upon cooling, the material with larger α\alpha contracts more and becomes the shorter side, so the strip bends toward that side (upward).

  3. Step 3

    ΔLA−ΔLB=L0(αA−αB)ΔT  ⟹  ΔLA−ΔLB=(15.0 cm)(1.78×10−5 ∘C−1)(−40.0∘C)  ⟹  ΔLA−ΔLB=−1.07×10−2 cm\Delta L_A - \Delta L_B = L_0(\alpha_A - \alpha_B)\Delta T \implies \Delta L_A - \Delta L_B = (15.0\text{ cm})(1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) \implies \Delta L_A - \Delta L_B = -1.07 \times 10^{-2}\text{ cm}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the net temperature change of −40.0∘C-40.0^\circ\text{C}.

You correctly evaluated the differential thermal strain and showed it is negative.

You set up and accurately calculated the numerical contraction difference in Part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Thermal expansion curvature direction upon cooling

You assumed that a higher expansion coefficient always makes the strip bend away from that layer, overlooking the reversal that occurs during cooling.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

A bimetallic beam bends toward the layer that ends up shorter. When heated (ΔT>0\Delta T > 0), the layer with larger α\alpha expands more, forming the longer outer curve (bending away). When cooled (ΔT<0\Delta T < 0), the layer with larger α\alpha contracts more, forming the shorter inner curve (bending toward that layer).

REASONING PATH
Your ACEpath teacher’s suggested approach
Inner vs. Outer Curve Rule
  • In any curved bonded strip, the layer on the concave (inner) side is shorter than the layer on the convex (outer) side.

  • Identify which layer becomes shorter after the temperature change; that layer must lie on the inside of the bend.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Note that ΔT=−40.0∘C<0\Delta T = -40.0^\circ\text{C} < 0, which signifies cooling.

  2. Compare linear contraction: because αA>αB\alpha_A > \alpha_B, strip A (brass, top) shrinks more than strip B (Invar, bottom).

  3. Since the top strip becomes shorter than the bottom strip, the top strip forms the inner concave curve.

  4. Deduce the deflection: curling concave-up causes the free right tip to tilt upward along the positive yy-axis.

Final answer

(a) Upward deflection; (b) ΔLA−ΔLB=−1.07×10−2 cm=−1.07×10−4 m\Delta L_A - \Delta L_B = -1.07 \times 10^{-2}\text{ cm} = -1.07 \times 10^{-4}\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always check the sign of ΔT\Delta T: heating makes the high-α\alpha side longer (outer arc), while cooling makes the high-α\alpha side shorter (inner arc).

  • Practice sketching the two strips separately as contracted bars first to visualize which layer must sit on the inside of the curve.

OverviewACEpath Teacher's Diagnosis

02 The student calculates temperature change as T₀ - T₁ instead of T₁ - T₀, resulting in an incorrect positive differential strain and deflection direction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔT=25.0∘C−(−15.0∘C)=40.0∘C\Delta T = 25.0^\circ\text{C} - (-15.0^\circ\text{C}) = 40.0^\circ\text{C}

    Correct

    ΔT=T1−T0=−15.0∘C−25.0∘C=−40.0∘C\Delta T = T_1 - T_0 = -15.0^\circ\text{C} - 25.0^\circ\text{C} = -40.0^\circ\text{C}

    Temperature change is defined as final temperature minus initial temperature (ΔT=Tfinal−Tinitial\Delta T = T_{\text{final}} - T_{\text{initial}}). Because the strip is cooled from 25.0∘C25.0^\circ\text{C} down to −15.0∘C-15.0^\circ\text{C}, ΔT\Delta T must be negative.

  2. Step 2

    Δϵ=(αA−αB)ΔT=(1.78×10−5 ∘C−1)(40.0∘C)>0  ⟹  \Delta \epsilon = (\alpha_A - \alpha_B)\Delta T = (1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(40.0^\circ\text{C}) > 0 \implies Because Δϵ>0\Delta \epsilon > 0, the top expands more than the bottom, so the strip bends downward.

    Correct

    Δϵ=(αA−αB)ΔT=(1.78×10−5 ∘C−1)(−40.0∘C)=−7.12×10−4<0  ⟹  \Delta \epsilon = (\alpha_A - \alpha_B)\Delta T = (1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -7.12 \times 10^{-4} < 0 \implies The top layer contracts more than the bottom layer, so the strip curls concave-up and deflects upward.

    Your physical reasoning connecting the sign of strain to the bending direction was logical, but substituting a positive ΔT\Delta T led to Δϵ>0\Delta \epsilon > 0. In reality, Δϵ<0\Delta \epsilon < 0, meaning the top brass layer contracts more than Invar, forcing the strip to deflect upward.

  3. Step 3

    ΔLA−ΔLB=L0(αA−αB)ΔT  ⟹  ΔLA−ΔLB=(15.0 cm)(1.78×10−5 ∘C−1)(40.0∘C)  ⟹  ΔLA−ΔLB=1.07×10−2 cm\Delta L_A - \Delta L_B = L_0 (\alpha_A - \alpha_B)\Delta T \implies \Delta L_A - \Delta L_B = (15.0\text{ cm})(1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(40.0^\circ\text{C}) \implies \Delta L_A - \Delta L_B = 1.07 \times 10^{-2}\text{ cm}

    Correct

    ΔLA−ΔLB=L0(αA−αB)ΔT=(15.0 cm)(1.78×10−5 ∘C−1)(−40.0∘C)=−1.07×10−2 cm=−1.07×10−4 m\Delta L_A - \Delta L_B = L_0 (\alpha_A - \alpha_B)\Delta T = (15.0\text{ cm})(1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -1.07 \times 10^{-2}\text{ cm} = -1.07 \times 10^{-4}\text{ m}

    Your formula and arithmetic magnitude were correct, but the sign was affected by the positive ΔT\Delta T from Step 1. The result should be negative to indicate net contraction.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the difference in linear expansion coefficients as αA−αB=1.78×10−5 ∘C−1\alpha_A - \alpha_B = 1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1}.

You correctly related the differential strain to the temperature change using Δϵ=(αA−αB)ΔT\Delta \epsilon = (\alpha_A - \alpha_B)\Delta T.

You correctly applied the relationship ΔLA−ΔLB=L0Δϵ\Delta L_A - \Delta L_B = L_0 \Delta \epsilon to determine the differential linear change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign Error in Temperature Change

You evaluated ΔT\Delta T as T0−T1T_0 - T_1 instead of T1−T0T_1 - T_0.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating ΔT\Delta T as a positive temperature difference rather than a signed change (Tfinal−TinitialT_{\text{final}} - T_{\text{initial}}) obscures whether the materials expand or contract, flipping the deflection direction in thermal bending problems.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Change
  • Δ(quantity)=final−initial\Delta(\text{quantity}) = \text{final} - \text{initial}

  • Always write ΔT=T1−T0\Delta T = T_1 - T_0 explicitly before substituting numbers.

Physical Sanity Check
  • Cooling (ΔT<0\Delta T < 0) causes contraction; the material with the larger α\alpha becomes shorter and forms the inner (concave) arc.

  • Check whether the strip is being heated or cooled before determining curvature.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the correct temperature change: ΔT=T1−T0=−15.0∘C−25.0∘C=−40.0∘C\Delta T = T_1 - T_0 = -15.0^\circ\text{C} - 25.0^\circ\text{C} = -40.0^\circ\text{C}.

  2. Calculate the differential thermal strain: Δϵ=(αA−αB)ΔT=(1.78×10−5 ∘C−1)(−40.0∘C)=−7.12×10−4\Delta \epsilon = (\alpha_A - \alpha_B)\Delta T = (1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -7.12 \times 10^{-4}.

  3. Interpret deflection: Since Δϵ<0\Delta \epsilon < 0, the top layer (brass) contracts more than the bottom layer (Invar), making the top shorter and curving the strip upward.

  4. Calculate the differential length change: ΔLA−ΔLB=L0Δϵ=(0.150 m)(−7.12×10−4)=−1.07×10−4 m=−0.107 mm\Delta L_A - \Delta L_B = L_0 \Delta \epsilon = (0.150\text{ m})(-7.12 \times 10^{-4}) = -1.07 \times 10^{-4}\text{ m} = -0.107\text{ mm}.

Final answer

(a) Upward deflection (Δϵ=−7.12×10−4<0\Delta \epsilon = -7.12 \times 10^{-4} < 0); (b) ΔLA−ΔLB=−1.07×10−4 m=−0.107 mm\Delta L_A - \Delta L_B = -1.07 \times 10^{-4}\text{ m} = -0.107\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how sign conventions in ΔT\Delta T dictate thermal expansion versus contraction.

  • Practice visualizing curvature by identifying which layer forms the shorter (inner) radius of the curved strip.

OverviewACEpath Teacher's Diagnosis

03 The student misaligns the decimal powers when subtracting expansion coefficients by treating 1.20 × 10⁻⁶ as 0.12 × 10⁻⁶ instead of 0.12 × 10⁻⁵.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=−15.0∘C−25.0∘C=−40.0∘C\Delta T = -15.0^\circ\text{C} - 25.0^\circ\text{C} = -40.0^\circ\text{C} ⟹\Longrightarrow Δϵ=(αA−αB)ΔT<0\Delta \epsilon = (\alpha_A - \alpha_B)\Delta T < 0 ⟹\Longrightarrow Since brass on top contracts more than Invar, the strip curves concave upward, deflecting upward.

  2. Step 2

    αA−αB=1.90×10−5−0.012×10−5=1.888×10−5 ∘C−1\alpha_A - \alpha_B = 1.90 \times 10^{-5} - 0.012 \times 10^{-5} = 1.888 \times 10^{-5}\text{ }^\circ\text{C}^{-1}

    Correct

    αA−αB=1.90×10−5 ∘C−1−0.120×10−5 ∘C−1=1.78×10−5 ∘C−1\alpha_A - \alpha_B = 1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1} - 0.120 \times 10^{-5}\text{ }^\circ\text{C}^{-1} = 1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1}

    You misaligned the decimal place when adjusting the exponent of αB\alpha_B. Increasing the exponent by one power of ten from 10−610^{-6} to 10−510^{-5} shifts the decimal point one place to the left, yielding 0.120×10−50.120 \times 10^{-5}, not 0.012×10−50.012 \times 10^{-5}.

  3. Step 3

    ΔLA−ΔLB=L0(αA−αB)ΔT=(15.0 cm)(1.888×10−5 ∘C−1)(−40.0∘C)=−1.13×10−2 cm\Delta L_A - \Delta L_B = L_0(\alpha_A - \alpha_B)\Delta T = (15.0\text{ cm})(1.888 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -1.13 \times 10^{-2}\text{ cm}

    Correct

    ΔLA−ΔLB=(0.150 m)(1.78×10−5 ∘C−1)(−40.0∘C)=−1.07×10−4 m=−1.07×10−2 cm\Delta L_A - \Delta L_B = (0.150\text{ m})(1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C}) = -1.07 \times 10^{-4}\text{ m} = -1.07 \times 10^{-2}\text{ cm}

    Your formula and substitution logic were correct, but the calculated length difference carries over the numerical error from the previous subtraction.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the temperature change ΔT=−40.0∘C\Delta T = -40.0^\circ\text{C} accurately.

You related the sign of the differential thermal strain Δϵ\Delta \epsilon to the physical bending direction correctly.

You set up the correct linear expansion difference equation ΔLA−ΔLB=L0(αA−αB)ΔT\Delta L_A - \Delta L_B = L_0(\alpha_A - \alpha_B)\Delta T.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Scientific Notation Conversion Error

You shifted the decimal point two places instead of one when converting 1.20×10−61.20 \times 10^{-6} to base 10−510^{-5}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When matching exponents for addition or subtraction, remember that increasing the power of ten by +1+1 (from −6-6 to −5-5) corresponds to dividing the mantissa by 10110^1, shifting the decimal point exactly one position left (1.20→0.1201.20 \to 0.120).

REASONING PATH
Your ACEpath teacher’s suggested approach
Exponent Matching Rule
  • a×10−n=(a×10−1)×10−(n−1)a \times 10^{-n} = (a \times 10^{-1}) \times 10^{-(n-1)}

  • Shift the decimal point left by 1 digit for every +1 increase in the exponent.

Magnitude Sanity Check
  • 1.20×10−61.20 \times 10^{-6} is approximately 6%6\% of 1.90×10−51.90 \times 10^{-5}.

  • Ensure the subtracted term reduces the leading digit visibly (to 1.781.78, not 1.8881.888).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. αA−αB=1.78×10−5 ∘C−1\alpha_A - \alpha_B = 1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1}

  2. ΔLA−ΔLB=L0(αA−αB)ΔT=(15.0 cm)(1.78×10−5 ∘C−1)(−40.0∘C)\Delta L_A - \Delta L_B = L_0 (\alpha_A - \alpha_B) \Delta T = (15.0\text{ cm})(1.78 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(-40.0^\circ\text{C})

  3. ΔLA−ΔLB=−1.068×10−2 cm≈−1.07×10−2 cm=−0.107 mm\Delta L_A - \Delta L_B = -1.068 \times 10^{-2}\text{ cm} \approx -1.07 \times 10^{-2}\text{ cm} = -0.107\text{ mm}

Final answer

-1.07 ×\times 10^{-4} m\text{ m}  (or \text{ (or } -0.107$\text{ mm})\text{)}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting numbers between different powers of ten before subtracting.

  • Use scientific notation mode on your calculator to verify intermediate differences like αA−αB\alpha_A - \alpha_B.

Lock it in

Similar question

01

A bimetallic strip consists of aluminum (α=2.4×10−5 K−1\alpha = 2.4 \times 10^{-5}\text{ K}^{-1}) on the left and steel (α=1.2×10−5 K−1\alpha = 1.2 \times 10^{-5}\text{ K}^{-1}) on the right, clamped vertically at the bottom. If the strip is cooled by 30 K30\text{ K}, does the free top end bend toward the left or toward the right?

Answer

Toward the left. Both metals contract, but aluminum has a larger α\alpha, so it contracts more than steel. The shorter side forms the inner curve, curling the strip toward the left (aluminum side).

02

A bimetallic thermostat strip of initial length L0=10.0 cmL_0 = 10.0\text{ cm} has copper (α1=1.70×10−5 ∘C−1\alpha_1 = 1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1}) on top and iron (α2=1.20×10−5 ∘C−1\alpha_2 = 1.20 \times 10^{-5}\text{ }^\circ\text{C}^{-1}) on the bottom. Find the difference in linear expansion (ΔL1−ΔL2)(\Delta L_1 - \Delta L_2) when the temperature rises by 50.0∘C50.0^\circ\text{C}, and state the direction of curvature.

Answer

ΔL1−ΔL2=+2.50×10−3 cm\Delta L_1 - \Delta L_2 = +2.50 \times 10^{-3}\text{ cm} (or +2.50×10−5 m+2.50 \times 10^{-5}\text{ m}), bending downward. Key steps: ΔL1−ΔL2=L0(α1−α2)ΔT=(10.0 cm)(0.50×10−5 ∘C−1)(50.0∘C)=2.50×10−3 cm\Delta L_1 - \Delta L_2 = L_0(\alpha_1 - \alpha_2)\Delta T = (10.0\text{ cm})(0.50 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(50.0^\circ\text{C}) = 2.50 \times 10^{-3}\text{ cm}. Since ΔT>0\Delta T > 0, copper expands more, forming the longer outer top arc, which curves the strip downward.

03

Two identical-geometry bimetallic strips are clamped horizontally at the left. Strip 1 has brass on top and Invar on the bottom; Strip 2 has zinc (αZn=3.0×10−5 ∘C−1\alpha_{\text{Zn}} = 3.0 \times 10^{-5}\text{ }^\circ\text{C}^{-1}) on top and Invar on the bottom. If both are cooled by the same ΔT=−20∘C\Delta T = -20^\circ\text{C}, which strip deflects upward by a greater tip displacement? Justify using differential strain Δϵ\Delta \epsilon.

Answer

Strip 2 deflects upward by a greater displacement. Key steps: Differential strain is Δϵ=(αtop−αInvar)ΔT\Delta \epsilon = (\alpha_{\text{top}} - \alpha_{\text{Invar}})\Delta T. Since αZn>αbrass>αInvar\alpha_{\text{Zn}} > \alpha_{\text{brass}} > \alpha_{\text{Invar}}, the magnitude of differential strain ∣Δϵ∣|\Delta \epsilon| is larger for the zinc-Invar strip. Greater strain mismatch across equal beam thickness yields a smaller radius of curvature, producing a sharper upward deflection.

Loading workspace…