Resources
A small test bead of mass is dropped from rest from a large height and falls vertically through a fluid medium where it experiences a velocity-dependent resistive drag force given by , with drag constant . Using : (a) determine the asymptotic terminal velocity of the bead as time , and (b) determine the limiting rate of mechanical energy dissipation (power converted into thermal energy, ) in watts as the bead approaches this terminal regime.
Answer and steps
Final answer
(a) , (b)
Steps
Part (a): Determining the Terminal Velocity
When the bead falls through the fluid, it experiences two vertical forces:
- The downward gravitational force:
- The upward resistive drag force opposes the direction of motion:
Applying Newton's second law along the downward vertical axis gives:
As the bead accelerates, its speed increases, which continuously increases the magnitude of the opposing drag force . As , the upward drag force grows until it precisely balances the downward gravitational force, causing the net force and the acceleration to approach zero:
Solving for the terminal speed :
Substitute the given numerical values:
Part (b): Limiting Rate of Mechanical Energy Dissipation
Mechanical energy is dissipated into thermal energy via the work done against fluid friction. The instantaneous rate of work done by the resistive drag force is given by power:
In the terminal regime, the speed remains constant at , meaning the kinetic energy of the bead does not change. Therefore, all the rate of gravitational potential energy loss is directly converted into thermal power:
Using , we can also express this limiting power directly in terms of given parameters:
Substitute the values:
(A common pitfall is calculating the total power dissipated over time by integrating, whereas the question asks for the limiting rate of dissipation, which is instantaneous power evaluated at steady terminal velocity).
Typical errors
01 The student inverts the force balance ratio as v_t = b/(m·g), confusing the numerator and denominator when solving for terminal velocity.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When solving for , you add to both sides to get , and then divide by , yielding rather than .
- Step 3Correct
Your formula is conceptually correct, but substituting your incorrect value for led to an inaccurate final dissipation rate.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that acceleration is zero at terminal speed, setting .
You applied the correct physical relation for drag power dissipation, .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally inverted the ratio when isolating , writing instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIsolating an unknown term multiplied by a coefficient can lead to an inverted fraction if you divide by the wrong factor without checking dimensional units or writing out the intermediate step .
REASONING PATH
Your ACEpath teacher’s suggested approach- Isolate the Variable Systematically
For an equation of the form , adding gives , so .
Write out explicitly before dividing both sides by the drag coefficient .
- Dimensional / Unit Consistency Check
Speed has units of . Since is in and is in , yields , whereas gives (slowness).
Perform a quick mental unit check whenever you obtain a ratio to confirm that numerator and denominator are in the right places.
CORRECTED PATH
ACEpath Teacher's DemonstrationSolve for : .
Substitute numerical values: .
Calculate the rate of energy dissipation: (or equivalently, ).
(a) , (b)
02 The student misidentifies power dissipation as F_d / v instead of F_d · v, resulting in an incorrect formula for mechanical energy loss.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Instantaneous mechanical power delivered or dissipated by a force is given by , which is the product of force and velocity, not the quotient.
- Step 3Correct
Because the formula in the previous step was inverted, your numerical result equaled instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly balanced the gravitational force and fluid drag force under steady terminal conditions.
You accurately calculated the numerical terminal velocity as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided drag force by velocity instead of multiplying them to compute power.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the relationship between force, velocity, and power (), possibly due to dimensional misattribution where power was mistaken for a force gradient over velocity.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional check for power
Power has units of watts: .
Always verify that . Dividing yields , which cannot represent power.
- Work-energy equivalence in terminal fall
At constant terminal velocity, kinetic energy is constant, so gravitational potential energy loss rate equals thermal dissipation rate: .
Use as a cross-check against .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the instantaneous power definition: .
Substitute and into the formula.
Compute .
(a) , (b)
03 The student calculates kinetic energy instead of mechanical power dissipation, confusing the rate of energy loss with total kinetic energy at terminal speed.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You wrote the formula for kinetic energy () instead of the instantaneous rate of energy dissipation (power, ). Kinetic energy represents stored energy in Joules, whereas the rate of energy dissipation is power in Watts.
- Step 3Correct
Your arithmetic is consistent with your formula, but the value is incorrect because it evaluates the bead's kinetic energy rather than its dissipated power.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly balanced the upward drag force with the downward gravitational force at terminal equilibrium.
You accurately calculated the numerical terminal velocity as .
You correctly carried out arithmetic operations with proper unit conversion.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused total kinetic energy (, in Joules) with the rate of mechanical energy dissipation (, in Watts). At terminal velocity, the bead's kinetic energy remains constant, while potential energy is continuously dissipated into thermal energy by the drag force at a rate of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Differentiating Energy and Power
Energy is an accumulated quantity measured in Joules (), whereas power is the time rate of energy transfer or dissipation measured in Watts ().
When asked for a rate of energy loss, always use power (), never a static energy formula such as or .
- Rate of Work Done by Drag
The instantaneous power dissipated by a resistive force is .
For linear drag , write , or equivalently since at terminal speed.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the definition of instantaneous dissipated power: .
Substitute and (or use ).
Calculate the numerical power: .
(a) , (b)
Lock it in
How do you correctly isolate terminal speed from the force balance equation ?
Add to both sides to get , then divide by : . (Units: )
Similar question
A droplet of mass falls through air where linear drag dominates with . Taking , find its terminal velocity and the rate of thermal power dissipation at terminal velocity.
Answer
At terminal velocity, . The dissipation rate is .
A ball of mass is released in a viscous liquid where drag is . If the terminal speed is measured to be (using ), determine the drag coefficient and verify the mechanical power dissipated at this speed.
Answer
From , we isolate : . The power dissipated is (or ).
An object falls in a medium experiencing quadratic drag, . Derive the formula for terminal velocity and show that the rate of mechanical energy dissipation at terminal velocity is .
Answer
- Force balance: .\n2. Power dissipated by drag is .\n3. Substituting gives .