Resources
In a resonance tube experiment used to measure sound speed in a laboratory at , a variable-frequency speaker is positioned directly above a vertical glass cylinder partially filled with water. A graduated water reservoir adjusts the water column height, creating a closed acoustic boundary at the water surface and an open boundary at the top of the tube. When driven at , consecutive acoustic resonances are detected at measured water-level distances from the top lip of and . (a) Using the difference between consecutive resonances to eliminate the end-correction error , determine the experimental wavelength of the sound wave. (b) Calculate the experimentally measured sound speed . (c) Calculate the acoustic end correction for this tube.
Answer and steps
Final answer
(a) ; (b) ; (c) (or ).
Steps
(a) Determining the Wavelength
A vertical resonance tube with water forms an air column closed at the bottom (by the water surface) and open at the top.
At the open top, the displacement antinode extends slightly past the physical rim of the tube by an acoustic end correction, . Consequently, the effective acoustic length of the air column includes this offset:
- For the fundamental (first) resonance mode:
- For the next consecutive resonance mode:
Subtracting the first equation from the second eliminates the end correction :
Solving for the wavelength :
Substitute the measured tube lengths and :
(b) Calculating the Experimental Speed of Sound
The speed of a wave relates to its frequency and wavelength through the wave speed formula:
Substitute and :
(c) Calculating the Acoustic End Correction
Using the relationship for the first resonance condition:
Substitute and :
Common Pitfall: A common mistake is calculating the wavelength directly as . This incorrectly assumes the displacement antinode forms precisely at the physical rim of the cylinder, ignoring the end correction . Subtracting two consecutive resonance lengths cancels and yields an accurate wavelength measurement.
Typical errors
01 The student confuses the distance between consecutive resonances in a tube with a quarter wavelength instead of a half wavelength.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Consecutive resonance modes in a tube closed at one end occur at odd quarter-wavelengths, and . Subtracting them gives , so the wavelength is twice the difference, not four times.
- Step 2Correct
Your formula and arithmetic were carried out correctly, but the speed was doubled because of the wavelength error in step 1.
- Step 3Correct
You used the correct equation for the end correction , but the result was thrown off by the incorrect value of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly subtracted the two column heights to isolate the distance between consecutive resonance positions.
You accurately applied the wave equation .
You correctly identified and applied the end-correction relation .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the fundamental acoustic length with the spacing between consecutive resonance positions .
REASONING PATH
Your ACEpath teacher’s suggested approach- Spacing Between Consecutive Standing Wave Nodes
For any standing wave, the distance between adjacent nodes (or adjacent antinodes) is always .
When subtracting consecutive resonance lengths , set the difference equal to .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the difference between consecutive resonances to a half-wavelength: .
Solve for : .
Compute speed: .
Compute end correction: .
(a) , (b) , (c)
02 The student fails to convert the wavelength from centimeters to meters, resulting in a sound speed that is off by a factor of 100.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
While your arithmetic is numerically consistent with the unit , wave speed in physics is standardly expressed in SI units () rounded to the appropriate number of significant figures ( significant figures: ). You should convert to meters before computing .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the consecutive resonance spacing formula to eliminate the unknown end correction.
You accurately calculated the end correction in centimeters using the fundamental resonance condition.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou left the wave speed in with excessive digits instead of converting the wavelength to meters to express the final speed in standard .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisForgetting to convert intermediate lengths to base SI units (meters) when applying the wave equation , which leads to non-standard units () and unrounded figures.
REASONING PATH
Your ACEpath teacher’s suggested approach- Standard SI Units for Wave Speed
In SI units, wave speed is measured in meters per second (), which requires frequency in Hertz () and wavelength in meters ().
Always convert lengths measured in centimeters to meters by dividing by before calculating wave speed.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the wavelength to meters: .
Substitute and into the wave speed formula: .
Round to 3 significant figures: .
03 The student ignores the end correction when finding wavelength and assumes the first resonance is exactly one-quarter wavelength.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because an antinode forms slightly outside the physical top rim of the tube by an end correction , the true acoustic condition is and . Subtracting these two gives , which cancels .
- Step 2Correct
Your application of the wave speed formula is structurally sound, but the numerical result is affected by your earlier underestimated wavelength value.
- Step 3Correct
You substituted your value of into the correct definition of end correction. Because you originally defined , this step inevitably produced .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the wave speed relationship .
You accurately identified the relationship for calculating the end correction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set assuming the displacement antinode sits right at the physical rim of the cylinder.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou overlooked that open-ended acoustic boundaries form their displacement antinode slightly outside the tube opening by an unknown distance . Whenever two consecutive resonance lengths and are provided, their difference is required to cancel out before solving for .
REASONING PATH
Your ACEpath teacher’s suggested approach- Consecutive Resonances in a Closed-Open Tube
The distance between any two consecutive displacement nodes (or antinodes) is always exactly , meaning .
Always find wavelength from when multiple resonance positions are recorded.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the difference between consecutive resonances to eliminate : .
Calculate experimental sound speed: .
Calculate end correction: (or ).
(a) ; (b) ; (c) (or )
Lock it in
What is the spatial distance between two consecutive displacement nodes (or antinodes) in any standing wave?
The distance is . A complete wavelength contains two consecutive node-to-node loops.
Similar question
A resonance tube open at the top and closed by water at the bottom is driven by a tuning fork. The first two resonances occur at and . Calculate the wavelength and the speed of sound .
Answer
and . Step 1: . Step 2: .
In a laboratory experiment at where sound speed is , a speaker at excites standing waves in a vertical resonance column. Find: (a) the separation between consecutive water-level resonance positions, and (b) the physical length of the third resonance if the acoustic end correction is .
Answer
(a) , (b) . Step 1: . Step 2: Consecutive resonance spacing is . Step 3: For the third resonance (, which is the 5th harmonic), the effective acoustic length is ? Note that consecutive resonances are , , . So , or if defined by spacing: .
A cylindrical pipe open at both ends resonates at consecutive frequencies of and . If the speed of sound in the pipe is , determine the effective acoustic length of the pipe and its fundamental resonance frequency.
Answer
Effective length and fundamental frequency . Step 1: For a pipe open at both ends, consecutive harmonics differ by . Step 2: Since , we have .