Resources
A test vehicle carrying experimental braking packages slides down a rough incline inclined at above the horizontal. The vehicle starts from rest at the top and slides a distance of along the ramp. At the base of the ramp, sensors measure its speed to be . During the descent, thermal energy generated by friction represents the entire non-conservative work done on the vehicle. Taking , reverse-engineer: (a) the acceleration of the vehicle down the incline, (b) the coefficient of kinetic friction between the vehicle and the incline surface, and (c) the fraction of the initial gravitational potential energy that was dissipated as thermal energy.
Answer and steps
Final answer
(a) ; (b) ; (c) (or )
Steps
Part (a): Acceleration of the Vehicle Down the Incline
The vehicle undergoes motion with constant acceleration along the straight ramp. Using the kinematic relation connecting initial velocity , final velocity , acceleration , and displacement :
Since the vehicle starts from rest, :
Substitute the given values and :
Part (b): Coefficient of Kinetic Friction
Set up a coordinate system with the -axis pointing down the ramp and the -axis perpendicular to the ramp:
- Perpendicular to the ramp (-direction): The forces are balanced, so the normal force is:
- Down the ramp (-direction): The component of gravity pulls the vehicle down, while kinetic friction opposes the motion:
Substitute into Newton's second law:
Dividing both sides by the mass :
Solve for :
Substitute , , and :
Part (c): Fraction of Initial Potential Energy Dissipated
Let the base of the ramp be the reference level where gravitational potential energy is zero ().
- Initial mechanical energy at the top: The vertical height of the ramp is . With :
- Final mechanical energy at the base: At the base, all remaining mechanical energy is kinetic:
- Energy dissipated by friction: By the work-energy theorem, the non-conservative work done by friction converts mechanical energy into thermal energy :
-
Fraction dissipated:
Since , this simplifies directly to:
Substitute and :
Typical errors
01 The student forgets the factor of 2 in the kinematic equation v² = 2aL, leading to an acceleration that is twice the correct value and propagating this into subsequent parts.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the kinematic relation without the factor of . The correct kinematic formula relating velocity, constant acceleration, and displacement from rest is .
- Step 2Correct
Your force balance down the ramp was set up correctly, but substituting the incorrect acceleration from Part (a) caused the calculated friction coefficient to become unphysically negative.
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the forces parallel and perpendicular to the inclined plane using Newton's second law.
You recognized that mass cancels when solving for the coefficient of kinetic friction.
You calculated both the initial gravitational potential energy and final kinetic energy directly from the given values to find the exact dissipated fraction in Part (c).
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou dropped the factor of in the kinematic relation, writing instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMissing the factor of in the constant-acceleration formula led to an acceleration value larger than the frictionless component of gravity (), which produced an unphysical negative kinetic friction coefficient in Part (b).
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinematic Relation Check
For constant acceleration starting from rest, work-energy equivalence implies .
Verify that your velocity-displacement relation always includes the denominator of when solving for acceleration: .
- Physical Reality Check for Friction
On a downward incline resisting motion, the acceleration must be less than , so .
If your calculated turns out negative, check whether your acceleration exceeded due to an earlier calculation error.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate the acceleration using : .
Substitute into the force balance equation: .
Solve for : .
(a) ; (b) ; (c) (or )
02 The student assumes the normal force on an incline is N = mg instead of N = mg cos(θ), underestimating the friction coefficient.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
On an inclined plane, the surface supports only the perpendicular component of gravity, so . Using overstates the normal force for a given friction force and results in an incorrect value for .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the constant-acceleration kinematic formula to find the acceleration down the incline.
You correctly identified that gravity provides a driving force component of parallel to the slope.
You set up the energy balance properly to find the fraction of initial mechanical energy dissipated by friction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeIn part (b), you wrote instead of resolving the gravitational force perpendicular to the ramp ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating horizontal surfaces (where when no vertical acceleration is present) with inclined surfaces, forgetting that the normal axis tilts with the incline and balances only the component .
REASONING PATH
Your ACEpath teacher’s suggested approach- Resolve Forces in the Normal Direction
For a ramp tilted at angle with no perpendicular acceleration, Newton's second law gives , so .
Always draw coordinate axes aligned parallel and perpendicular to the ramp surface before writing the normal force equation.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) ; (b) ; (c) (or )
03 The student calculates the fraction of energy remaining as kinetic energy rather than the fraction dissipated as thermal energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You computed the fraction of initial energy that remains as kinetic energy () instead of the fraction lost to friction as thermal energy ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used kinematics to find the acceleration down the incline.
You set up the net force balance correctly using Newton's second law to solve for the coefficient of kinetic friction.
You correctly expressed both the initial potential energy and final kinetic energy in terms of the vehicle mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou found the fraction of mechanical energy retained () instead of the fraction dissipated ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the ratio of preserved kinetic energy to initial energy with the ratio of dissipated thermal energy to initial energy.
REASONING PATH
Your ACEpath teacher’s suggested approach- Define the target energy quantity
Dissipated thermal energy equals initial mechanical energy minus final mechanical energy: .
Always write the numerator of your ratio explicitly in terms of the thermal loss before plugging in values.
- Complementary ratio check
.
When you find the ratio of final kinetic energy, subtract it from to get the fraction dissipated.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the thermal energy generated by friction: .
Divide by the initial energy to find the fraction dissipated: .
(a) ; (b) ; (c)
Lock it in
What is the kinematic equation relating velocity change, uniform acceleration , and displacement ?
. The factor of comes from integrating acceleration over distance (or equating to ).
Similar question
A sled accelerates from rest down a snow-covered hill of length inclined at . Its final speed at the bottom is . Taking , find the sled's acceleration and the coefficient of kinetic friction .
Answer
, . Key steps: . From , .
A crate slides down a ramp from rest. If friction dissipates exactly of the initial gravitational potential energy, what is the coefficient of kinetic friction between the crate and the ramp?
Answer
. Key steps: Initial potential energy is , and thermal energy generated is . The dissipated fraction is . Since , .
A test cart starts from rest on a ramp of angle and length where . Taking , calculate its final speed at the bottom and the percentage of initial potential energy converted into kinetic energy.
Answer
, kinetic energy. Key steps: . Final speed . The kinetic energy fraction is .