Resources

A standard 0.250 W0.250\text{ W} rated metal-film resistor has an electrical resistance of R=1.60×103 ΩR = 1.60 \times 10^3\ \Omega. To prevent permanent thermal breakdown, the maximum electrical power dissipation must not exceed its 0.250 W0.250\text{ W} operating threshold. (a) Calculate the critical threshold voltage VmaxV_{\text{max}} that can be placed across the resistor without exceeding this power rating. (b) Calculate the corresponding critical threshold current ImaxI_{\text{max}} passing through the resistor at this physical boundary. (c) If a student inadvertently applies a voltage of V=30.0 VV = 30.0\text{ V}, explain whether the current, voltage, or resistance fundamentally dictates the component failure.

Answer and steps

Final answer

(a) Vmax=20.0 VV_{\text{max}} = 20.0\text{ V}; (b) Imax=1.25×10−2 A=12.5 mAI_{\text{max}} = 1.25 \times 10^{-2}\text{ A} = 12.5\text{ mA}; (c) At V=30.0 VV = 30.0\text{ V}, the dissipated power is P=V2R=(30.0 V)21600 Ω=0.563 W>0.250 WP = \frac{V^2}{R} = \frac{(30.0\text{ V})^2}{1600\ \Omega} = 0.563\text{ W} > 0.250\text{ W}; component failure is caused by excessive thermal energy generated per unit time, resulting from current driven beyond the physical heat dissipation limit dictated by the combination of voltage and the element's fixed resistance.

Steps

Part (a): Maximum Operating Voltage (VmaxV_{\text{max}})

The electric power PP dissipated in a resistor of resistance RR subjected to a potential difference VV is given by Joule's Law:

P=V2RP = \frac{V^2}{R}

Rearranging this relationship to solve for the maximum allowable voltage VmaxV_{\text{max}} for a given maximum power rating Pmax=0.250 WP_{\text{max}} = 0.250\text{ W}:

Vmax=Pmax⋅RV_{\text{max}} = \sqrt{P_{\text{max}} \cdot R}

Substitute the given values:

Vmax=0.250 W⋅1.60×103 Ω=400 V2=20.0 VV_{\text{max}} = \sqrt{0.250\text{ W} \cdot 1.60 \times 10^3\ \Omega} = \sqrt{400\text{ V}^2} = 20.0\text{ V}


Part (b): Maximum Operating Current (ImaxI_{\text{max}})

The power dissipated can also be expressed in terms of electric current II and resistance RR:

P=I2RP = I^2 R

Rearranging for the maximum safe current ImaxI_{\text{max}}:

Imax=PmaxRI_{\text{max}} = \sqrt{\frac{P_{\text{max}}}{R}}

Alternatively, using Ohm's law (Imax=VmaxRI_{\text{max}} = \frac{V_{\text{max}}}{R}):

Imax=20.0 V1.60×103 Ω=1.25×10−2 A=12.5 mAI_{\text{max}} = \frac{20.0\text{ V}}{1.60 \times 10^3\ \Omega} = 1.25 \times 10^{-2}\text{ A} = 12.5\text{ mA}


Part (c): Analysis of Component Failure

  1. Calculate the Power at V=30.0 VV = 30.0\text{ V}:

    P=V2R=(30.0 V)21600 Ω=900 V21600 Ω=0.563 WP = \frac{V^2}{R} = \frac{(30.0\text{ V})^2}{1600\ \Omega} = \frac{900\text{ V}^2}{1600\ \Omega} = 0.563\text{ W}

    Since 0.563 W>0.250 W0.563\text{ W} > 0.250\text{ W}, the power exceeds the safe operating threshold.

  2. Physical Cause of Failure:

    • Resistance (RR): An intrinsic physical property of the material and geometry; it determines how strongly charge carriers are opposed, but does not actively drive energy transfer on its own.
    • Voltage (VV): The driving electrical potential difference (force per unit charge) that establishes the electric field across the resistor.
    • Current (II): The actual flow of charge carriers. Electrical power is converted into thermal internal energy via inelastic collisions between moving electrons and the ionic lattice (Joule heating).

    Component failure occurs because the thermal dissipation rate exceeds the physical cooling rate of the resistor package, causing thermal breakdown. This excessive heating is driven by the applied voltage pushing excessive current through the fixed resistance, so the failure fundamentally arises from the rate of thermal energy generation exceeding the rated threshold.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to take the square root when rearranging P = V²/R, calculating V_max = P · R instead of √(P · R).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=V2R  ⟹  P⋅R=0.250⋅1600=400 VP = \frac{V^2}{R} \implies P \cdot R = 0.250 \cdot 1600 = 400\text{ V}

    Correct

    Vmax=P⋅R=0.250 W⋅1600 Ω=20.0 VV_{\text{max}} = \sqrt{P \cdot R} = \sqrt{0.250\text{ W} \cdot 1600\ \Omega} = 20.0\text{ V}

    You selected the correct power formula P=V2RP = \frac{V^2}{R}, but multiplying both sides by RR yields V2=P⋅RV^2 = P \cdot R. You forgot to take the square root to solve for VV, which gave 400 V400\text{ V} instead of 400 V2=20.0 V\sqrt{400\text{ V}^2} = 20.0\text{ V}.

  2. Step 2

    Imax=PR=0.2501600=0.0125 AI_{\text{max}} = \sqrt{\frac{P}{R}} = \sqrt{\frac{0.250}{1600}} = 0.0125\text{ A}

  3. Step 3

    "Current dictates failure because Joule heating caused by current exceeding the threshold leads to thermal destruction."

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct physical formulas relating power, current, voltage, and resistance for every part of the problem.

You took the square root correctly when solving for current in part (b).

You correctly linked thermal failure to Joule heating caused by excessive current in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Radical in Inversion

You equated VV directly to P⋅RP \cdot R instead of writing V2=P⋅RV^2 = P \cdot R and completing the inversion with a square root.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating V2V^2 as VV during intermediate algebraic manipulation, failing to invert the quadratic power term before substituting values.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate the Squared Term Explicitly
  • If P=V2RP = \frac{V^2}{R}, then multiplying by RR gives V2=P⋅RV^2 = P \cdot R, not V=P⋅RV = P \cdot R.

  • Always write the intermediate line V2=…V^2 = \dots before taking the square root: V=P⋅RV = \sqrt{P \cdot R}.

Unit and Dimensional Sanity Check
  • The product of power and resistance has units W⋅Ω=(J/s)⋅(V/A)=V⋅A⋅(V/A)=V2\text{W} \cdot \Omega = (\text{J}/\text{s}) \cdot (\text{V}/\text{A}) = \text{V} \cdot \text{A} \cdot (\text{V}/\text{A}) = \text{V}^2.

  • Notice that P⋅RP \cdot R carries units of V2\text{V}^2, signaling that a square root is mathematically required to yield volts (V\text{V}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from the power relation: P=Vmax2RP = \frac{V_{\text{max}}^2}{R}

  2. Multiply both sides by RR: Vmax2=P⋅RV_{\text{max}}^2 = P \cdot R

  3. Take the principal square root: Vmax=P⋅RV_{\text{max}} = \sqrt{P \cdot R}

  4. Substitute the numerical values: Vmax=0.250 W⋅1600 Ω=400 V2=20.0 VV_{\text{max}} = \sqrt{0.250\text{ W} \cdot 1600\ \Omega} = \sqrt{400\text{ V}^2} = 20.0\text{ V}

Final answer

(a) Vmax=20.0 VV_{\text{max}} = 20.0\text{ V}; (b) Imax=12.5 mAI_{\text{max}} = 12.5\text{ mA}; (c) Component failure fundamentally results from thermal destruction caused by Joule heating when current exceeds the safe power rating.

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out intermediate algebraic steps showing exponents before clearing them with radicals.

  • Perform a quick dimensional check whenever solving for linear variables from quadratic energy/power expressions.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers the power formula as P = I · R² instead of P = I² · R, resulting in an incorrect critical current calculation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Vmax=P⋅R=0.250⋅1600=20.0 VV_{\text{max}} = \sqrt{P \cdot R} = \sqrt{0.250 \cdot 1600} = 20.0\text{ V}

  2. Step 2

    P=I⋅R2  ⟹  Imax=PR2=0.250(1600)2=9.77×10−8 AP = I \cdot R^2 \implies I_{\text{max}} = \frac{P}{R^2} = \frac{0.250}{(1600)^2} = 9.77 \times 10^{-8}\text{ A}

    Correct

    P=I2R  ⟹  Imax=PmaxR=0.250 W1600 Ω=1.25×10−2 A=12.5 mAP = I^2 R \implies I_{\text{max}} = \sqrt{\frac{P_{\text{max}}}{R}} = \sqrt{\frac{0.250\text{ W}}{1600\ \Omega}} = 1.25 \times 10^{-2}\text{ A} = 12.5\text{ mA}

    You placed the exponent on resistance rather than current. The correct power relation is P=I2RP = I^2 R, or equivalently by Ohm's law, Imax=VmaxR=20.0 V1600 Ω=12.5 mAI_{\text{max}} = \frac{V_{\text{max}}}{R} = \frac{20.0\text{ V}}{1600\ \Omega} = 12.5\text{ mA}.

  3. Step 3

    Current dictates failure because excessive current produces thermal dissipation that burns out the resistor.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly rearranged P=V2RP = \frac{V^2}{R} to solve for the maximum operating voltage in part (a).

You correctly identified that thermal dissipation from charge flow is the physical mechanism causing the resistor to burn out in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula transcription error

You squared the resistance instead of the current when writing down Joule's power formula.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the location of the exponent in the two standard power formulas: voltage is squared over resistance (P=V2RP = \frac{V^2}{R}), whereas current is squared times resistance (P=I2RP = I^2 R).

REASONING PATH
Your ACEpath teacher’s suggested approach
Deriving Joule's Law from Fundamental Definitions
  • Electric power is P=IVP = I V. Substituting Ohm's law V=IRV = I R gives P=I(IR)=I2RP = I(I R) = I^2 R.

  • Always rebuild the power formula from P=IVP = I V and V=IRV = I R if you are uncertain where the square belongs.

Cross-Checking with Ohm's Law
  • At the critical operating point, VmaxV_{\text{max}} and ImaxI_{\text{max}} must satisfy Ohm's law: Imax=VmaxRI_{\text{max}} = \frac{V_{\text{max}}}{R}.

  • Verify your calculated current against your calculated voltage: 20.0 V1600 Ω=0.0125 A\frac{20.0\text{ V}}{1600\ \Omega} = 0.0125\text{ A}, which exposes that 9.77×10−8 A9.77 \times 10^{-8}\text{ A} is unphysically small.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from the correct Joule heating formula: P=I2RP = I^2 R.

  2. Divide both sides by RR: I2=PRI^2 = \frac{P}{R}.

  3. Take the square root of both sides: Imax=PmaxRI_{\text{max}} = \sqrt{\frac{P_{\text{max}}}{R}}.

  4. Substitute the numerical values: Imax=0.250 W1600 Ω=1.5625×10−4 A2=1.25×10−2 A=12.5 mAI_{\text{max}} = \sqrt{\frac{0.250\text{ W}}{1600\ \Omega}} = \sqrt{1.5625 \times 10^{-4}\text{ A}^2} = 1.25 \times 10^{-2}\text{ A} = 12.5\text{ mA}.

Final answer

(a) Vmax=20.0 VV_{\text{max}} = 20.0\text{ V}; (b) Imax=1.25×10−2 A=12.5 mAI_{\text{max}} = 1.25 \times 10^{-2}\text{ A} = 12.5\text{ mA}; (c) Excessive Joule heating driven by current exceeding the package power rating (0.563 W>0.250 W0.563\text{ W} > 0.250\text{ W}) causes thermal failure.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three fundamental representations of electric power: P=IVP = IV, P=I2RP = I^2 R, and P=V2RP = \frac{V^2}{R}.

  • Practice checking consistency between parts by verifying V=IRV = I R with your computed values.

  • Solve the practice problems below to reinforce choosing and rearranging the correct power formulas.

OverviewACEpath Teacher's Diagnosis

03 The student believes applied voltage directly causes breakdown as an electrostatic or field breakdown, ignoring that thermal failure in a resistor is fundamentally caused by excessive current and Joule heating.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Vmax=P⋅R=0.250⋅1600=20.0 VV_{\text{max}} = \sqrt{P \cdot R} = \sqrt{0.250 \cdot 1600} = 20.0\text{ V}

  2. Step 2

    Imax=PR=0.2501600=0.0125 AI_{\text{max}} = \sqrt{\frac{P}{R}} = \sqrt{\frac{0.250}{1600}} = 0.0125\text{ A}

  3. Step 3

    Voltage dictates failure because the applied voltage of 30.0 V exceeds the maximum rated voltage of 20.0 V.

    Correct

    At V=30.0 VV = 30.0\text{ V}, P=V2R=0.563 W>0.250 WP = \frac{V^2}{R} = 0.563\text{ W} > 0.250\text{ W}. Component failure is fundamentally caused by excessive current: flowing charge carriers collide inelastically with the crystal lattice, generating thermal energy via Joule heating (P=I2RP = I^2 R) faster than the package can dissipate heat to the environment.

    You noted that the voltage exceeded the nominal rating, but voltage is only the external driving potential difference. Resistor breakdown is fundamentally a thermal failure caused by excessive charge carrier flow (current) dissipating heat through lattice collisions beyond the physical cooling threshold.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived and calculated the critical voltage threshold using the power-voltage relation.

You correctly derived and calculated the critical current threshold using the power-current relation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing driving variable with physical mechanism

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You selected voltage because the numerical voltage value exceeded the threshold calculated in part (a), confusing the external circuit variable with the internal physical mechanism: thermal burnout in a resistor is caused by charge carriers (current) transferring excessive kinetic energy to the lattice as heat (I2RI^2 R).

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish driving potential from the physical mechanism of heating
  • Voltage establishes the electric field, but current represents the physical flow of charge whose collisions with lattice ions produce Joule heating (P=I2RP = I^2 R).

  • When explaining thermal component breakdown, attribute the physical failure to excessive heat generation driven by charge carrier collisions (current) rather than treating voltage as a direct physical destructive force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the actual power dissipated when 30.0 V30.0\text{ V} is applied: P=V2R=(30.0 V)21600 Ω=0.563 WP = \frac{V^2}{R} = \frac{(30.0\text{ V})^2}{1600\ \Omega} = 0.563\text{ W}, which exceeds the 0.250 W0.250\text{ W} safe rating.

  2. Analyze the microscopic role of each quantity: resistance is a passive material and geometric property; voltage is the external electric potential difference that drives charges; current is the rate of charge flow through the material.

  3. Conclude that thermal breakdown occurs because excessive current leads to intense Joule heating (P=I2RP = I^2 R), creating internal thermal energy at a rate higher than the package can radiate or conduct away.

Final answer

(a) Vmax=20.0 VV_{\text{max}} = 20.0\text{ V}; (b) Imax=0.0125 A=12.5 mAI_{\text{max}} = 0.0125\text{ A} = 12.5\text{ mA}; (c) Excessive current fundamentally dictates thermal failure because charge carrier collisions produce Joule heat (P=I2RP = I^2 R) beyond the resistor's physical heat dissipation threshold.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the microscopic model of conduction (Drude model) to see how electron-lattice collisions convert electrical energy into thermal energy.

  • Contrast thermal breakdown in conductors/resistors (current-induced heating) with dielectric breakdown in insulators (electric-field-induced ionization).

Lock it in

Similar question

01

A 0.50 W0.50\text{ W} carbon-composition resistor has a resistance of 200 Ω200\ \Omega. Calculate the maximum allowable direct-current voltage VmaxV_{\text{max}} that can be sustained across this resistor without exceeding its power rating.

Answer

Vmax=P⋅R=0.50 W⋅200 Ω=100 V2=10 VV_{\text{max}} = \sqrt{P \cdot R} = \sqrt{0.50\text{ W} \cdot 200\ \Omega} = \sqrt{100\text{ V}^2} = 10\text{ V}.

02

A surface-mount resistor rated at 0.125 W0.125\text{ W} is connected across a fixed 5.0 V5.0\text{ V} supply. (a) Determine the minimum safe resistance RminR_{\text{min}} that prevents thermal damage. (b) Calculate the resulting current II at this boundary.

Answer

(a) Rmin=V2P=(5.0 V)20.125 W=250.125=200 ΩR_{\text{min}} = \frac{V^2}{P} = \frac{(5.0\text{ V})^2}{0.125\text{ W}} = \frac{25}{0.125} = 200\ \Omega. (b) I=VR=5.0 V200 Ω=0.025 A=25 mAI = \frac{V}{R} = \frac{5.0\text{ V}}{200\ \Omega} = 0.025\text{ A} = 25\text{ mA}.

03

Two resistors, R1=500 ΩR_1 = 500\ \Omega and R2=2000 ΩR_2 = 2000\ \Omega, each have an identical maximum power rating of Prated=0.500 WP_{\text{rated}} = 0.500\text{ W}. If they are connected in parallel across an adjustable voltage source VV, determine the maximum voltage Vsource, maxV_{\text{source, max}} that can be applied without damaging either component, and identify which resistor limits the system.

Answer

For parallel resistors, both experience the same voltage VV. The voltage limit for each is Vmax=P⋅RV_{\text{max}} = \sqrt{P \cdot R}. For R1R_1: V1=0.500⋅500=250≈15.8 VV_1 = \sqrt{0.500 \cdot 500} = \sqrt{250} \approx 15.8\text{ V}. For R2R_2: V2=0.500⋅2000=1000≈31.6 VV_2 = \sqrt{0.500 \cdot 2000} = \sqrt{1000} \approx 31.6\text{ V}. Since both share the source voltage, R1R_1 dissipates power faster (P=V2RP = \frac{V^2}{R} is larger for smaller RR), so R1R_1 sets the maximum system voltage: Vsource, max=250 V≈15.8 VV_{\text{source, max}} = \sqrt{250}\text{ V} \approx 15.8\text{ V}.

Loading workspace…