Resources

A student expects that pushing the narrow piston of a hydraulic lift down by a small distance will lift a massive load on the wide piston by an equal distance. Consider an ideal, leak-free hydraulic lift filled with an incompressible fluid, where the input piston has a radius of r1=1.80 cmr_1 = 1.80\text{ cm} and the output piston has a radius of r2=18.0 cmr_2 = 18.0\text{ cm}. If an operator pushes the input piston downward by a distance of d1=25.0 cmd_1 = 25.0\text{ cm} with a constant force of F1=90.0 NF_1 = 90.0\text{ N}, determine: (a) the displacement distance d2d_2 that the output piston moves upward, and (b) verify the conservation of energy by computing the input work W1W_1 and the output work W2W_2.

Answer and steps

Final answer

(a) d2=0.250 cmd_2 = 0.250\text{ cm}; (b) W1=22.5 JW_1 = 22.5\text{ J} and W2=22.5 JW_2 = 22.5\text{ J}

Steps

Part (a): Determine the displacement distance d2d_2 of the output piston

  1. Relate the displaced fluid volumes
    Because the hydraulic fluid is incompressible and enclosed in a leak-free system, the volume of fluid pushed down by the input piston (V1V_1) must equal the volume of fluid that lifts the output piston (V2V_2): V1=V2V_1 = V_2 A1d1=A2d2A_1 d_1 = A_2 d_2 where A1A_1 and A2A_2 are the cross-sectional areas of the pistons, and d1d_1 and d2d_2 are their respective displacements.
  2. Express the areas in terms of radii
    For circular pistons: A1=πr12andA2=πr22A_1 = \pi r_1^2 \quad \text{and} \quad A_2 = \pi r_2^2 Substituting these into the volume equation gives: πr12d1=πr22d2  ⟹  d2=d1(r1r2)2\pi r_1^2 d_1 = \pi r_2^2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2
  3. Calculate d2d_2
    Substitute the given values (r1=1.80 cmr_1 = 1.80\text{ cm}, r2=18.0 cmr_2 = 18.0\text{ cm}, and d1=25.0 cmd_1 = 25.0\text{ cm}): r1r2=1.80 cm18.0 cm=110\frac{r_1}{r_2} = \frac{1.80\text{ cm}}{18.0\text{ cm}} = \frac{1}{10} d2=25.0 cm×(110)2=25.0 cm×1100=0.250 cmd_2 = 25.0\text{ cm} \times \left(\frac{1}{10}\right)^2 = 25.0\text{ cm} \times \frac{1}{100} = 0.250\text{ cm}

Common Pitfall: A common mistake is to scale the displacement by the radius ratio r1r2\frac{r_1}{r_2} rather than the area ratio (r1r2)2\left(\frac{r_1}{r_2}\right)^2. The volume depends on the cross-sectional area, so the displacement is reduced by the square of the radius ratio.


Part (b): Verify conservation of energy by computing W1W_1 and W2W_2

  1. Calculate the input work (W1W_1)
    Convert the input displacement into meters: d1=25.0 cm=0.250 md_1 = 25.0\text{ cm} = 0.250\text{ m}.
    The work done on the input piston by the constant force F1=90.0 NF_1 = 90.0\text{ N} is: W1=F1d1=(90.0 N)(0.250 m)=22.5 JW_1 = F_1 d_1 = (90.0\text{ N})(0.250\text{ m}) = 22.5\text{ J}
  2. Determine the output force (F2F_2) using Pascal's principle
    According to Pascal's principle, pressure is transmitted equally throughout an enclosed fluid: P1=P2  ⟹  F1A1=F2A2P_1 = P_2 \implies \frac{F_1}{A_1} = \frac{F_2}{A_2} F2=F1(A2A1)=F1(r2r1)2F_2 = F_1 \left(\frac{A_2}{A_1}\right) = F_1 \left(\frac{r_2}{r_1}\right)^2 F2=90.0 N×(10)2=90.0 N×100=9000 NF_2 = 90.0\text{ N} \times (10)^2 = 90.0\text{ N} \times 100 = 9000\text{ N}
  3. Calculate the output work (W2W_2)
    Convert the output displacement into meters: d2=0.250 cm=0.00250 md_2 = 0.250\text{ cm} = 0.00250\text{ m}.
    The work delivered by the output piston is: W2=F2d2=(9000 N)(0.00250 m)=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}

Since W1=W2=22.5 JW_1 = W_2 = 22.5\text{ J}, energy is conserved. Although the output force is magnified by a factor of 100100, the distance moved is reduced by the exact same factor of 100100, meaning a hydraulic lift provides a mechanical advantage without creating extra work.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses a linear ratio of radii instead of area ratio (radius squared) for volume conservation and force multiplication.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V1=V2  ⟹  d2=d1⋅(r1r2)=25.0 cm⋅(1.8018.0)=2.50 cmV_1 = V_2 \implies d_2 = d_1 \cdot \left(\frac{r_1}{r_2}\right) = 25.0\text{ cm} \cdot \left(\frac{1.80}{18.0}\right) = 2.50\text{ cm}

    Correct

    V1=V2  ⟹  A1d1=A2d2  ⟹  d2=d1(r1r2)2=25.0 cm⋅(110)2=0.250 cmV_1 = V_2 \implies A_1 d_1 = A_2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 25.0\text{ cm} \cdot \left(\frac{1}{10}\right)^2 = 0.250\text{ cm}

    Piston displacement scales inversely with cross-sectional area A=πr2A = \pi r^2, not with radius rr. Because the radius increases by a factor of 1010, the area increases by a factor of 102=10010^2 = 100, meaning d2d_2 is reduced by 100100 rather than 1010.

  2. Step 2

    W1=F1⋅d1=90.0 N⋅0.250 m=22.5 JW_1 = F_1 \cdot d_1 = 90.0\text{ N} \cdot 0.250\text{ m} = 22.5\text{ J}

  3. Step 3

    F2=F1⋅(r2r1)=90.0 N⋅(18.01.80)=900 N  ⟹  W2=F2⋅d2=900 N⋅0.0250 m=22.5 JF_2 = F_1 \cdot \left(\frac{r_2}{r_1}\right) = 90.0\text{ N} \cdot \left(\frac{18.0}{1.80}\right) = 900\text{ N} \implies W_2 = F_2 \cdot d_2 = 900\text{ N} \cdot 0.0250\text{ m} = 22.5\text{ J}

    Correct

    F2=F1(r2r1)2=90.0 N×100=9000 N  ⟹  W2=F2d2=(9000 N)(0.00250 m)=22.5 JF_2 = F_1 \left(\frac{r_2}{r_1}\right)^2 = 90.0\text{ N} \times 100 = 9000\text{ N} \implies W_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}

    According to Pascal's principle, pressure is transmitted equally: F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}. Force multiplication scales with the area ratio (r2r1)2=100\left(\frac{r_2}{r_1}\right)^2 = 100, which gives F2=9000 NF_2 = 9000\text{ N}.

  4. Step 4

    W1=W2=22.5 J, so energy is conserved.W_1 = W_2 = 22.5\text{ J}\text{, so energy is conserved.}

    Correct

    W1=W2=22.5 JW_1 = W_2 = 22.5\text{ J}

    Your final work values matched and satisfied conservation of energy only because the linear ratio error in force cancelled out the linear ratio error in distance.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that fluid volume is conserved between the two cylinders (V1=V2V_1 = V_2).

You correctly calculated the input work W1=F1d1W_1 = F_1 d_1 using proper SI units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear radius scaling instead of area scaling

You set the volume and pressure ratios proportional to r1r2\frac{r_1}{r_2} rather than the circular cross-sectional area ratio (r1r2)2\left(\frac{r_1}{r_2}\right)^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating cross-sectional area as linear with radius rather than quadratic (A=πr2A = \pi r^2) when applying volume conservation (A1d1=A2d2A_1 d_1 = A_2 d_2) and Pascal's principle (F1/A1=F2/A2F_1 / A_1 = F_2 / A_2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Cross-sectional area of circular pistons
  • For a circular piston of radius rr, the cross-sectional area is A=πr2A = \pi r^2.

  • Always write down A1=πr12A_1 = \pi r_1^2 and A2=πr22A_2 = \pi r_2^2 before forming ratios of areas.

Scaling factors in hydraulics
  • Both force amplification and distance reduction depend on the area ratio A2A1=(r2r1)2\frac{A_2}{A_1} = \left(\frac{r_2}{r_1}\right)^2.

  • When piston radius increases by a factor of kk, multiply force by k2k^2 and divide displacement by k2k^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. A1d1=A2d2  ⟹  d2=d1(r1r2)2=25.0 cm×(1.8018.0)2=25.0 cm×1100=0.250 cmA_1 d_1 = A_2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 25.0\text{ cm} \times \left(\frac{1.80}{18.0}\right)^2 = 25.0\text{ cm} \times \frac{1}{100} = 0.250\text{ cm}

  2. F2=F1(r2r1)2=90.0 N×100=9000 NF_2 = F_1 \left(\frac{r_2}{r_1}\right)^2 = 90.0\text{ N} \times 100 = 9000\text{ N}

  3. W2=F2d2=(9000 N)(0.00250 m)=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}

Final answer

(a) d2=0.250 cmd_2 = 0.250\text{ cm}; (b) W1=22.5 JW_1 = 22.5\text{ J} and W2=22.5 JW_2 = 22.5\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how area and volume scale with radius (A∝r2A \propto r^2, V∝r2dV \propto r^2 d).

  • Practice deriving Pascal's principle equations explicitly with πr2\pi r^2 before substituting numerical values.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the radius ratio, incorrectly thinking the wider piston moves a larger distance than the narrow piston.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1⋅d1=A2⋅d2  ⟹  d2=d1⋅(r2r1)2=25.0 cm⋅(18.01.80)2=2500 cmA_1 \cdot d_1 = A_2 \cdot d_2 \implies d_2 = d_1 \cdot \left(\frac{r_2}{r_1}\right)^2 = 25.0\text{ cm} \cdot \left(\frac{18.0}{1.80}\right)^2 = 2500\text{ cm}

    Correct

    A1d1=A2d2  ⟹  d2=d1(r1r2)2=25.0 cm⋅(1.80 cm18.0 cm)2=0.250 cmA_1 d_1 = A_2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 25.0\text{ cm} \cdot \left(\frac{1.80\text{ cm}}{18.0\text{ cm}}\right)^2 = 0.250\text{ cm}

    When solving A1d1=A2d2A_1 d_1 = A_2 d_2 for d2d_2, dividing both sides by A2A_2 yields d2=d1A1A2=d1(r1r2)2d_2 = d_1 \frac{A_1}{A_2} = d_1 \left(\frac{r_1}{r_2}\right)^2. You inverted the radius ratio, which incorrectly multiplied the displacement by 100100 instead of dividing by 100100.

  2. Step 2

    W1=F1⋅d1=90.0 N⋅0.250 m=22.5 JW_1 = F_1 \cdot d_1 = 90.0\text{ N} \cdot 0.250\text{ m} = 22.5\text{ J}

  3. Step 3

    F2=F1⋅(r1r2)2=90.0 N⋅(1.8018.0)2=0.900 NF_2 = F_1 \cdot \left(\frac{r_1}{r_2}\right)^2 = 90.0\text{ N} \cdot \left(\frac{1.80}{18.0}\right)^2 = 0.900\text{ N}

    Correct

    F2=F1(A2A1)=F1(r2r1)2=90.0 N⋅(18.0 cm1.80 cm)2=9000 NF_2 = F_1 \left(\frac{A_2}{A_1}\right) = F_1 \left(\frac{r_2}{r_1}\right)^2 = 90.0\text{ N} \cdot \left(\frac{18.0\text{ cm}}{1.80\text{ cm}}\right)^2 = 9000\text{ N}

    By Pascal's principle, pressure is uniform: P=F1A1=F2A2P = \frac{F_1}{A_1} = \frac{F_2}{A_2}, so F2=F1(A2A1)=F1(r2r1)2F_2 = F_1 \left(\frac{A_2}{A_1}\right) = F_1 \left(\frac{r_2}{r_1}\right)^2. The larger output piston exerts a magnified force, not a smaller one.

  4. Step 4

    W2=F2⋅d2=0.900 N⋅25.0 m=22.5 J  ⟹  W1=W2=22.5 J, so energy is conserved.W_2 = F_2 \cdot d_2 = 0.900\text{ N} \cdot 25.0\text{ m} = 22.5\text{ J} \implies W_1 = W_2 = 22.5\text{ J}\text{, so energy is conserved.}

    Correct

    W2=F2d2=(9000 N)(0.00250 m)=22.5 J  ⟹  W1=W2=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J} \implies W_1 = W_2 = 22.5\text{ J}

    Although your final energy product matched 22.5 J22.5\text{ J}, both factor values were off by a factor of 1000010000 because the inverted displacement and inverted force cancelled out algebraically.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated the volume conservation equality A1d1=A2d2A_1 d_1 = A_2 d_2.

You correctly calculated the input work W1=22.5 JW_1 = 22.5\text{ J} using standard SI units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted area ratio in hydraulic scaling

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the algebraic ratios for both displacement and force, misunderstanding the trade-off in hydraulic systems: pushing a narrow piston down forces fluid into a wider cylinder where the fluid level rises much less, while the larger surface area multiplies the upward force.

REASONING PATH
Your ACEpath teacher’s suggested approach
Displacement trade-off
  • For an incompressible fluid, A1d1=A2d2A_1 d_1 = A_2 d_2. Since A2>A1A_2 > A_1, the output displacement must be smaller: d2=d1(r1r2)2<d1d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 < d_1.

  • Always check if the wider piston moves less distance than the narrow piston before finishing the calculation.

Force multiplication
  • Because pressure P=FAP = \frac{F}{A} is equal throughout, F2=F1(A2A1)=F1(r2r1)2F_2 = F_1 \left(\frac{A_2}{A_1}\right) = F_1 \left(\frac{r_2}{r_1}\right)^2.

  • Ensure that the larger piston exerts the larger force (F2>F1F_2 > F_1) to provide mechanical advantage.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve for output displacement: d2=d1(r1r2)2=25.0 cm×(1.8018.0)2=25.0 cm×1100=0.250 cmd_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 25.0\text{ cm} \times \left(\frac{1.80}{18.0}\right)^2 = 25.0\text{ cm} \times \frac{1}{100} = 0.250\text{ cm}.

  2. Calculate output force: F2=F1(r2r1)2=90.0 N×(10)2=9000 NF_2 = F_1 \left(\frac{r_2}{r_1}\right)^2 = 90.0\text{ N} \times (10)^2 = 9000\text{ N}.

  3. Compute output work: W2=F2d2=(9000 N)(0.00250 m)=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}.

Final answer

(a) d2=0.250 cmd_2 = 0.250\text{ cm}; (b) W1=22.5 JW_1 = 22.5\text{ J} and W2=22.5 JW_2 = 22.5\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Check hydraulic relationships with physical intuition: a wider piston must move less distance while exerting more force.

  • Take extra care when isolating variables from A1d1=A2d2A_1 d_1 = A_2 d_2 to divide by the correct cross-sectional area.

OverviewACEpath Teacher's Diagnosis

03 The student assumes piston displacements are equal (d₂ = d₁), ignoring the difference in cross-sectional areas.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    d2=d1  ⟹  d2=25.0 cmd_2 = d_1 \implies d_2 = 25.0\text{ cm}

    Correct

    A1d1=A2d2  ⟹  d2=d1(r1r2)2=25.0 cm×(1.80 cm18.0 cm)2=0.250 cmA_1 d_1 = A_2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 25.0\text{ cm} \times \left(\frac{1.80\text{ cm}}{18.0\text{ cm}}\right)^2 = 0.250\text{ cm}

    In an enclosed incompressible fluid, the volume pushed down at the input must equal the volume displaced at the output (V1=V2V_1 = V_2). Because the output piston has a much larger cross-sectional area, its displacement is reduced by the square of the radius ratio.

  2. Step 2

    W1=F1⋅d1=90.0 N⋅0.250 m=22.5 JW_1 = F_1 \cdot d_1 = 90.0\text{ N} \cdot 0.250\text{ m} = 22.5\text{ J}

  3. Step 3

    F2=F1⋅(r2r1)2=90.0 N⋅(18.01.80)2=9000 NF_2 = F_1 \cdot \left(\frac{r_2}{r_1}\right)^2 = 90.0\text{ N} \cdot \left(\frac{18.0}{1.80}\right)^2 = 9000\text{ N}

  4. Step 4

    W2=F2⋅d2=9000 N⋅0.250 m=2250 JW_2 = F_2 \cdot d_2 = 9000\text{ N} \cdot 0.250\text{ m} = 2250\text{ J}

    Correct

    W2=F2d2=(9000 N)(0.00250 m)=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}

    Your formula for work is correct, but the numerical result is affected by substituting the incorrect displacement from Step 1.

  5. Step 5

    W1≠W2, so energy is not conserved.W_1 \neq W_2\text{, so energy is not conserved.}

    Correct

    W1=W2=22.5 J, verifying energy conservation.W_1 = W_2 = 22.5\text{ J}\text{, verifying energy conservation.}

    Because d2d_2 was overestimated by a factor of 100100, your computed output work appeared much larger than the input work, leading to an incorrect conclusion about energy conservation.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the work done on the input piston using W1=F1d1W_1 = F_1 d_1.

You correctly applied Pascal's principle to calculate the magnified output force F2=F1(r2r1)2F_2 = F_1 \left(\frac{r_2}{r_1}\right)^2.

You correctly recognized that conservation of energy requires comparing input work W1W_1 with output work W2W_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Assuming Equal Piston Displacements

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that both pistons in a hydraulic lift displace by the same linear distance, overlooking that the incompressible fluid conserves volume (A1d1=A2d2A_1 d_1 = A_2 d_2) rather than linear distance. Because a hydraulic lift trades distance for force, magnifying force by (r2r1)2\left(\frac{r_2}{r_1}\right)^2 requires reducing displacement by (r1r2)2\left(\frac{r_1}{r_2}\right)^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservation of Volume in Hydraulics
  • For an incompressible fluid in an ideal hydraulic cylinder: V1=V2  ⟹  A1d1=A2d2V_1 = V_2 \implies A_1 d_1 = A_2 d_2.

  • Always solve for the secondary piston's stroke using the area ratio: d2=d1(A1A2)=d1(r1r2)2d_2 = d_1 \left(\frac{A_1}{A_2}\right) = d_1 \left(\frac{r_1}{r_2}\right)^2.

Work and Mechanical Advantage
  • An ideal machine cannot create energy: Win=Wout  ⟹  F1d1=F2d2W_{\text{in}} = W_{\text{out}} \implies F_1 d_1 = F_2 d_2.

  • Check that any gain in force is paired with an identical proportional loss in distance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Equate the displaced fluid volumes: A1d1=A2d2A_1 d_1 = A_2 d_2

  2. Substitute circular areas A=πr2A = \pi r^2: πr12d1=πr22d2  ⟹  d2=d1(r1r2)2\pi r_1^2 d_1 = \pi r_2^2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2

  3. Calculate d2d_2: d2=25.0 cm×(1.80 cm18.0 cm)2=25.0 cm×1100=0.250 cm=0.00250 md_2 = 25.0\text{ cm} \times \left(\frac{1.80\text{ cm}}{18.0\text{ cm}}\right)^2 = 25.0\text{ cm} \times \frac{1}{100} = 0.250\text{ cm} = 0.00250\text{ m}

  4. Compute the output work with the correct displacement: W2=F2d2=(9000 N)(0.00250 m)=22.5 JW_2 = F_2 d_2 = (9000\text{ N})(0.00250\text{ m}) = 22.5\text{ J}

  5. Compare input and output work: W1=W2=22.5 JW_1 = W_2 = 22.5\text{ J}, confirming energy is conserved.

Final answer

(a) d2=0.250 cmd_2 = 0.250\text{ cm}; (b) W1=22.5 JW_1 = 22.5\text{ J} and W2=22.5 JW_2 = 22.5\text{ J}, confirming energy is conserved.

NEXT STEPS
Final Takeaways from Your Teacher
  • Recompute piston displacements using volume conservation A1d1=A2d2A_1 d_1 = A_2 d_2 instead of equating displacements.

  • Double-check that whenever force increases by a factor MM, the travel distance decreases by the same factor MM so that work is conserved.

Lock it in

Similar question

01

A hydraulic press has an input cylinder of radius r1=2.0 cmr_1 = 2.0\text{ cm} and an output cylinder of radius r2=8.0 cmr_2 = 8.0\text{ cm}. If the input piston is pressed downward by d1=12.0 cmd_1 = 12.0\text{ cm}, find the upward displacement d2d_2 of the output piston.

Answer

d2=0.75 cmd_2 = 0.75\text{ cm}. By incompressibility, A1d1=A2d2  ⟹  d2=d1(r1r2)2=12.0 cm×(2.08.0)2=12.0×116=0.75 cmA_1 d_1 = A_2 d_2 \implies d_2 = d_1 \left(\frac{r_1}{r_2}\right)^2 = 12.0\text{ cm} \times \left(\frac{2.0}{8.0}\right)^2 = 12.0 \times \frac{1}{16} = 0.75\text{ cm}.

02

A mechanic uses a hydraulic car lift where the slave cylinder has a diameter of 30.0 cm30.0\text{ cm} and the master cylinder has a diameter of 3.0 cm3.0\text{ cm}. To lift a 15000 N15000\text{ N} vehicle at constant speed, what force F1F_1 must be applied to the master cylinder?

Answer

F1=150 NF_1 = 150\text{ N}. The ratio of diameters is D2D1=30.03.0=10\frac{D_2}{D_1} = \frac{30.0}{3.0} = 10. The area ratio is (D2D1)2=100\left(\frac{D_2}{D_1}\right)^2 = 100. By Pascal's principle, F1=F2(D1D2)2=15000 N×1100=150 NF_1 = F_2 \left(\frac{D_1}{D_2}\right)^2 = 15000\text{ N} \times \frac{1}{100} = 150\text{ N}.

03

In a hydraulic jack, an input piston of radius r1=1.0 cmr_1 = 1.0\text{ cm} is pushed down by 10.0 cm10.0\text{ cm} with a force of 50.0 N50.0\text{ N}. The output piston has radius r2=5.0 cmr_2 = 5.0\text{ cm}. Calculate (a) the output force F2F_2, (b) the output displacement d2d_2, and (c) verify conservation of energy by computing both works.

Answer

(a) F2=1250 NF_2 = 1250\text{ N}; (b) d2=0.40 cmd_2 = 0.40\text{ cm}; (c) W1=W2=5.0 JW_1 = W_2 = 5.0\text{ J}. Area ratio A2A1=52=25\frac{A_2}{A_1} = 5^2 = 25. Force is magnified: F2=50.0 N×25=1250 NF_2 = 50.0\text{ N} \times 25 = 1250\text{ N}. Displacement is reduced: d2=10.0 cm/25=0.40 cm=0.0040 md_2 = 10.0\text{ cm} / 25 = 0.40\text{ cm} = 0.0040\text{ m}. Works: W1=(50.0 N)(0.10 m)=5.0 JW_1 = (50.0\text{ N})(0.10\text{ m}) = 5.0\text{ J} and W2=(1250 N)(0.0040 m)=5.0 JW_2 = (1250\text{ N})(0.0040\text{ m}) = 5.0\text{ J}.

Loading workspace…