Resources

A wooden crate of mass m=24.0 kgm = 24.0\text{ kg} rests on a rough horizontal warehouse floor where the coefficient of static friction is μs=0.420\mu_s = 0.420 and the coefficient of kinetic friction is μk=0.310\mu_k = 0.310. A worker pulls on a rope attached to the crate with a force of magnitude T=115 NT = 115\text{ N} inclined at an angle of θ=25.0∘\theta = 25.0^\circ above the horizontal. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine whether the applied tension exceeds the threshold of impending slip. State the resulting net horizontal force F⃗net\vec{F}_{\text{net}} acting on the crate.

Answer and steps

Final answer

Does not slip (Tx=104 N≤fs,max=78.4 NT_x = 104\text{ N} \le f_{s,\text{max}} = 78.4\text{ N} is false, wait: FN=mg−Tsin⁡θ=235.2−48.6=186.6 NF_N = mg - T\sin\theta = 235.2 - 48.6 = 186.6\text{ N}; fs,max=0.420×186.6=78.4 Nf_{s,\text{max}} = 0.420 \times 186.6 = 78.4\text{ N}; since Tx=104.2 N>fs,maxT_x = 104.2\text{ N} > f_{s,\text{max}}, the crate slips); with kinetic friction fk=0.310×186.6 N=57.8 Nf_k = 0.310 \times 186.6\text{ N} = 57.8\text{ N}, the net horizontal force is F⃗net=46.4ı^ N\vec{F}_{\text{net}} = 46.4\hat{\imath}\text{ N} (magnitude 46.4 N46.4\text{ N} forward).

Steps

01

Resolve the applied tension into rectangular components

Choose a coordinate system where the positive xx-axis points horizontally in the direction of the pull and the positive yy-axis points vertically upward.

  • Horizontal component: Tx=Tcos⁡θ=115 N⋅cos⁡(25.0∘)≈104.2 NT_x = T \cos\theta = 115\text{ N} \cdot \cos(25.0^\circ) \approx 104.2\text{ N}
  • Vertical component: Ty=Tsin⁡θ=115 N⋅sin⁡(25.0∘)≈48.60 NT_y = T \sin\theta = 115\text{ N} \cdot \sin(25.0^\circ) \approx 48.60\text{ N}

02

Determine the normal force FNF_N

The forces acting along the vertical axis are the upward normal force FNF_N, the upward vertical component of tension TyT_y, and the downward force of gravity W=mgW = mg.

Since the crate does not accelerate vertically, ∑Fy=0\sum F_y = 0: FN+Ty−mg=0F_N + T_y - mg = 0

Substitute the given values: FN=mg−Ty=(24.0 kg⋅9.80 m/s2)−48.60 N=235.2 N−48.60 N=186.6 NF_N = mg - T_y = (24.0\text{ kg} \cdot 9.80\text{ m/s}^2) - 48.60\text{ N} = 235.2\text{ N} - 48.60\text{ N} = 186.6\text{ N}

Common Pitfall: Forgetting to subtract the upward component of the pull TyT_y leads to an overestimation of the normal force (FN≠mgF_N \ne mg), which would incorrectly increase the calculated friction forces.


03

Compare horizontal pulling force with maximum static friction

The maximum static friction threshold is: fs,max=μsFN=0.420⋅186.6 N≈78.4 Nf_{s,\text{max}} = \mu_s F_N = 0.420 \cdot 186.6\text{ N} \approx 78.4\text{ N}

Compare the horizontal pulling force TxT_x with fs,maxf_{s,\text{max}}: Tx=104.2 N>fs,max=78.4 NT_x = 104.2\text{ N} > f_{s,\text{max}} = 78.4\text{ N}

Because TxT_x exceeds fs,maxf_{s,\text{max}}, the applied tension exceeds the threshold of impending slip, and the crate begins to slide.


04

Calculate the kinetic friction and net horizontal force

Once the crate begins to move, the floor exerts a kinetic friction force opposing the motion: fk=μkFN=0.310⋅186.6 N≈57.8 Nf_k = \mu_k F_N = 0.310 \cdot 186.6\text{ N} \approx 57.8\text{ N}

The net horizontal force is the difference between the pulling component and kinetic friction: Fnet,x=Tx−fk=104.2 N−57.8 N=46.4 NF_{\text{net},x} = T_x - f_k = 104.2\text{ N} - 57.8\text{ N} = 46.4\text{ N}

Expressed as a vector in the forward direction (ı^\hat{\imath}): F⃗net=46.4ı^ N\vec{F}_{\text{net}} = 46.4\hat{\imath}\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the upward component of tension when finding the normal force, setting N = mg, which overestimates maximum static friction and incorrectly concludes the crate does not move.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    N=mg=24.0×9.80=235.2 NN = mg = 24.0 \times 9.80 = 235.2\text{ N}

    Correct

    N=mg−Tsin⁡θ=235.2 N−115sin⁡(25.0∘) N=186.6 NN = mg - T\sin\theta = 235.2\text{ N} - 115\sin(25.0^\circ)\text{ N} = 186.6\text{ N}

    You set the normal force equal to the gravitational force alone. Because the rope pulls upward at an angle θ=25.0∘\theta = 25.0^\circ, vertical equilibrium requires N+Tsin⁡θ−mg=0N + T\sin\theta - mg = 0, meaning N=mg−Tsin⁡θN = mg - T\sin\theta.

  2. Step 2

    fs,max⁡=μsN=0.420×235.2=98.78 Nf_{s,\max} = \mu_s N = 0.420 \times 235.2 = 98.78\text{ N}

    Correct

    fs,max⁡=μsN=0.420×186.6 N≈78.4 Nf_{s,\max} = \mu_s N = 0.420 \times 186.6\text{ N} \approx 78.4\text{ N}

    You used the correct formula for maximum static friction, but this value is affected by your overestimated normal force from Step 1.

  3. Step 3

    Tx=115cos⁡(25.0∘)=104.2 NT_x = 115\cos(25.0^\circ) = 104.2\text{ N}

  4. Step 4

    104.2 N>98.78 N104.2\text{ N} > 98.78\text{ N}, so the applied tension exceeds the threshold of impending slip.

    Correct

    Tx=104.2 N>fs,max⁡=78.4 NT_x = 104.2\text{ N} > f_{s,\max} = 78.4\text{ N}, so the applied tension exceeds the threshold of impending slip.

    Your comparison logic is correct, and by coincidence your conclusion holds, though the static friction threshold you compared against was carried over from Step 2.

  5. Step 5

    fk=μkN=0.310×235.2=72.91 Nf_k = \mu_k N = 0.310 \times 235.2 = 72.91\text{ N}

    Correct

    fk=μkN=0.310×186.6 N≈57.8 Nf_k = \mu_k N = 0.310 \times 186.6\text{ N} \approx 57.8\text{ N}

    You correctly applied the formula for kinetic friction, but the numerical result is affected by the incorrect normal force from Step 1.

  6. Step 6

    Fnet=Tx−fk=104.2−72.91=31.3 NF_{\text{net}} = T_x - f_k = 104.2 - 72.91 = 31.3\text{ N} in the direction of the pull

    Correct

    F⃗net=(Tx−fk)ı^=(104.2 N−57.8 N)ı^=46.4ı^ N\vec{F}_{\text{net}} = (T_x - f_k)\hat{\imath} = (104.2\text{ N} - 57.8\text{ N})\hat{\imath} = 46.4\hat{\imath}\text{ N}

    Your setup for the net horizontal force is correct, but because fkf_k was overestimated, your final magnitude is lower than the actual value of 46.4 N46.4\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You resolved the horizontal component of the pulling force accurately using cosine.

You correctly identified the criterion for impending slip by comparing TxT_x to maximum static friction.

You used the correct formula Fnet=Tx−fkF_{\text{net}} = T_x - f_k to determine the net horizontal force once the crate is in motion.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted vertical component of applied force in normal force equilibrium

You defaulted to N=mgN = mg without setting up a full vertical force balance ∑Fy=0\sum F_y = 0.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Assuming the normal force on a level surface is always equal to mgmg overlooks any vertical components from inclined external forces.

REASONING PATH
Your ACEpath teacher’s suggested approach
Vertical Force Balance Check
  • On a horizontal surface with no vertical acceleration, ∑Fy=N+Fext,y−mg=0\sum F_y = N + F_{\text{ext},y} - mg = 0.

  • Always draw a free-body diagram and resolve all forces with vertical components before writing an expression for NN.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve for the vertical component of the tension: Ty=Tsin⁡(25.0∘)=115sin⁡(25.0∘)=48.60 NT_y = T\sin(25.0^\circ) = 115\sin(25.0^\circ) = 48.60\text{ N}.

  2. Apply vertical equilibrium ∑Fy=N+Ty−mg=0\sum F_y = N + T_y - mg = 0 to find N=235.2 N−48.60 N=186.6 NN = 235.2\text{ N} - 48.60\text{ N} = 186.6\text{ N}.

  3. Recalculate maximum static friction: fs,max⁡=0.420×186.6 N=78.4 Nf_{s,\max} = 0.420 \times 186.6\text{ N} = 78.4\text{ N}. Since Tx=104.2 N>78.4 NT_x = 104.2\text{ N} > 78.4\text{ N}, slip occurs.

  4. Recalculate kinetic friction: fk=0.310×186.6 N=57.8 Nf_k = 0.310 \times 186.6\text{ N} = 57.8\text{ N}.

  5. Compute the net horizontal force: Fnet,x=Tx−fk=104.2 N−57.8 N=46.4 NF_{\text{net},x} = T_x - f_k = 104.2\text{ N} - 57.8\text{ N} = 46.4\text{ N}.

Final answer

The applied tension exceeds the threshold of impending slip; the resulting net horizontal force is F⃗net=46.4ı^ N\vec{F}_{\text{net}} = 46.4\hat{\imath}\text{ N} (or 46.4 N46.4\text{ N} forward).

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a quick free-body diagram for every problem involving angled forces to verify all vertical terms.

  • Write out ∑Fy=0\sum F_y = 0 explicitly instead of immediately replacing NN with mgmg.

OverviewACEpath Teacher's Diagnosis

02 The student compares the full tension magnitude T instead of its horizontal component T cos θ against the maximum static friction force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    N=mg−Tsin⁡(25.0∘)=24.0×9.80−115sin⁡(25.0∘)=186.6 NN = mg - T\sin(25.0^\circ) = 24.0 \times 9.80 - 115\sin(25.0^\circ) = 186.6\text{ N}

  2. Step 2

    fs,max=μsN=0.420×186.6=78.37 Nf_{s,\text{max}} = \mu_s N = 0.420 \times 186.6 = 78.37\text{ N}

  3. Step 3

    T=115 N>78.37 NT = 115\text{ N} > 78.37\text{ N}, so the applied tension exceeds the threshold of impending slip.

    Correct

    Tx=Tcos⁡(25.0∘)=115cos⁡(25.0∘)≈104.2 N>78.4 NT_x = T\cos(25.0^\circ) = 115\cos(25.0^\circ) \approx 104.2\text{ N} > 78.4\text{ N}

    Friction acts along the horizontal floor, so only the horizontal component Tx=Tcos⁡(25.0∘)T_x = T\cos(25.0^\circ), not the total tension TT, opposes static friction. While your conclusion that it slips is qualitatively correct, the comparison must be between TxT_x and fs,maxf_{s,\text{max}}.

  4. Step 4

    fk=μkN=0.310×186.6=57.85 N  ⟹  Fnet=T−fk=115−57.85=57.2 Nf_k = \mu_k N = 0.310 \times 186.6 = 57.85\text{ N} \implies F_{\text{net}} = T - f_k = 115 - 57.85 = 57.2\text{ N} in the direction of the pull

    Correct

    Fnet,x=Tcos⁡(25.0∘)−fk=104.2 N−57.85 N=46.4 NF_{\text{net},x} = T\cos(25.0^\circ) - f_k = 104.2\text{ N} - 57.85\text{ N} = 46.4\text{ N} (forward)

    You calculated kinetic friction fkf_k correctly, but you subtracted it from the total tension magnitude T=115 NT = 115\text{ N} directed along the rope rather than from the horizontal pulling component Tx=104.2 NT_x = 104.2\text{ N} along the floor.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly accounted for the upward component of the pull when calculating the normal force.

You correctly computed both the maximum static friction force and the kinetic friction force using FNF_N.

You correctly recognized that the crate slips when the horizontal pulling effort exceeds maximum static friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Used Full Force Instead of Component Along Motion Axis

You compared the full tension magnitude TT against static friction and subtracted horizontal friction directly from TT, rather than resolving tension along the horizontal axis of motion (Tx=Tcos⁡θT_x = T\cos\theta).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating a vector's total magnitude with its parallel component when working along a single coordinate axis. Because friction acts strictly parallel to the surface, Newton's second law along the surface must include only forces or components acting parallel to that surface.

REASONING PATH
Your ACEpath teacher’s suggested approach
Resolve Before Summing Along an Axis
  • Never add or subtract forces pointing in different directions. Along the horizontal axis of motion, only horizontal force components can be summed: ∑Fx=Tx−f=Tcos⁡θ−f\sum F_x = T_x - f = T\cos\theta - f.

  • Always break angled forces into separate xx- and yy-components immediately after drawing your free-body diagram.

Slip Condition Threshold
  • Impending motion on a horizontal surface is governed by the net horizontal pull: the object slips if and only if Fpull,∥>fs,maxF_{\text{pull},\parallel} > f_{s,\text{max}}.

  • Compare Tcos⁡θT\cos\theta against μsFN\mu_s F_N, never the total angled magnitude TT.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the horizontal pulling force: Tx=Tcos⁡(25.0∘)=115cos⁡(25.0∘)≈104.2 NT_x = T\cos(25.0^\circ) = 115\cos(25.0^\circ) \approx 104.2\text{ N}.

  2. Compare TxT_x with maximum static friction: 104.2 N>78.4 N104.2\text{ N} > 78.4\text{ N}, confirming that the applied tension exceeds the impending slip threshold.

  3. Calculate the net horizontal force using kinetic friction: Fnet,x=Tx−fk=104.2 N−57.8 N=46.4 NF_{\text{net},x} = T_x - f_k = 104.2\text{ N} - 57.8\text{ N} = 46.4\text{ N}.

Final answer

The applied tension exceeds the threshold of impending slip, and the resulting net horizontal force is F⃗net=46.4ı^ N\vec{F}_{\text{net}} = 46.4\hat{\imath}\text{ N} (or 46.4 N46.4\text{ N} forward).

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice resolving vectors into rectangular components immediately after sketching a free-body diagram.

  • Set up explicit ∑Fx\sum F_x and ∑Fy\sum F_y equations before inserting numerical values to ensure no off-axis magnitudes enter single-axis calculations.

OverviewACEpath Teacher's Diagnosis

03 The student adds the vertical component of tension to the gravitational force instead of subtracting it when determining the normal force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg+Tsin⁡(25.0∘)=283.8 NN = mg + T\sin(25.0^\circ) = 283.8\text{ N}

    Correct

    N=mg−Tsin⁡(25.0∘)=(24.0 kg)(9.80 m/s2)−(115 N)sin⁡(25.0∘)=235.2 N−48.60 N=186.6 NN = mg - T\sin(25.0^\circ) = (24.0\text{ kg})(9.80\text{ m/s}^2) - (115\text{ N})\sin(25.0^\circ) = 235.2\text{ N} - 48.60\text{ N} = 186.6\text{ N}

    Because the rope pulls upward at an angle above the horizontal, its vertical component Tsin⁡(25.0∘)T\sin(25.0^\circ) acts upward along with the normal force. In vertical equilibrium, N+Tsin⁡θ−mg=0N + T\sin\theta - mg = 0, so N=mg−Tsin⁡θN = mg - T\sin\theta. You added this term instead of subtracting it, which overestimated the normal force.

  2. Step 2

    fs,max⁡=μsN=0.420×283.8=119.2 Nf_{s,\max} = \mu_s N = 0.420 \times 283.8 = 119.2\text{ N}

    Correct

    fs,max⁡=μsN=0.420×186.6 N≈78.4 Nf_{s,\max} = \mu_s N = 0.420 \times 186.6\text{ N} \approx 78.4\text{ N}

    You correctly applied the static friction formula fs,max⁡=μsNf_{s,\max} = \mu_s N, but the numerical value was affected by your overestimated normal force from Step 1.

  3. Step 3

    Tx=115cos⁡(25.0∘)=104.2 NT_x = 115\cos(25.0^\circ) = 104.2\text{ N}

  4. Step 4

    104.2 N<119.2 N, so the applied tension does not exceed the threshold of impending slip.104.2\text{ N} < 119.2\text{ N}\text{, so the applied tension does not exceed the threshold of impending slip.}

    Correct

    Since Tx=104.2 N>fs,max⁡=78.4 NT_x = 104.2\text{ N} > f_{s,\max} = 78.4\text{ N}, the applied tension exceeds the threshold of impending slip and the crate begins to slide.

    Your comparison logic was valid for your values, but because the true threshold is 78.4 N78.4\text{ N}, the pulling force 104.2 N104.2\text{ N} actually overcomes static friction.

  5. Step 5

    Because the crate remains at rest, Fnet=0 N\text{Because the crate remains at rest, } F_{\text{net}} = 0\text{ N}

    Correct

    F⃗net=(Tx−fk)ı^=[104.2 N−(0.310)(186.6 N)]ı^=(104.2 N−57.8 N)ı^=46.4ı^ N\vec{F}_{\text{net}} = (T_x - f_k)\hat{\imath} = [104.2\text{ N} - (0.310)(186.6\text{ N})]\hat{\imath} = (104.2\text{ N} - 57.8\text{ N})\hat{\imath} = 46.4\hat{\imath}\text{ N}

    Because the crate actually slides, kinetic friction opposes the motion rather than static friction holding it at rest, resulting in a net forward force of 46.4 N46.4\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You resolved the horizontal component of the tension vector correctly using the cosine of the angle.

You used the correct relationship between maximum static friction and the normal force.

You correctly understood that if the applied horizontal force is less than maximum static friction, an object remains at rest with zero net force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal force vertical equilibrium sign error

You wrote N=mg+Tsin⁡θN = mg + T\sin\theta instead of N=mg−Tsin⁡θN = mg - T\sin\theta, adding the upward lift of the rope rather than subtracting it from the gravitational force.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing how upward angled forces affect contact pressure: pulling upward relieves contact pressure against the floor, meaning the floor supports less than the object's full weight (N<mgN < mg).

REASONING PATH
Your ACEpath teacher’s suggested approach
Set up $\sum F_y = 0$ explicitly
  • For a surface with upward normal force NN, downward gravity mgmg, and upward pulling force component TyT_y, the vertical equilibrium equation is N+Ty−mg=0N + T_y - mg = 0.

  • Always list all upward forces on one side and all downward forces on the other: N+Tsin⁡θ=mg  ⟹  N=mg−Tsin⁡θN + T\sin\theta = mg \implies N = mg - T\sin\theta.

Physical reality check on normal force
  • Pulling up on an object makes it feel lighter to the floor, reducing NN. Pushing downward makes it press harder into the floor, increasing NN.

  • Check whether your calculated normal force is smaller than mgmg for an upward pull and larger than mgmg for a downward push.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the correct normal force: FN=mg−Tsin⁡(25.0∘)=(24.0)(9.80)−115sin⁡(25.0∘)=235.2−48.60=186.6 NF_N = mg - T\sin(25.0^\circ) = (24.0)(9.80) - 115\sin(25.0^\circ) = 235.2 - 48.60 = 186.6\text{ N}.

  2. Compute the true maximum static friction: fs,max⁡=μsFN=0.420×186.6 N≈78.4 Nf_{s,\max} = \mu_s F_N = 0.420 \times 186.6\text{ N} \approx 78.4\text{ N}.

  3. Compare the horizontal pull to friction: Since Tx=104.2 N>78.4 NT_x = 104.2\text{ N} > 78.4\text{ N}, the crate overcomes static friction and slips.

  4. Calculate kinetic friction: fk=μkFN=0.310×186.6 N≈57.8 Nf_k = \mu_k F_N = 0.310 \times 186.6\text{ N} \approx 57.8\text{ N}.

  5. Compute the net horizontal force: F⃗net=(Tx−fk)ı^=(104.2−57.8)ı^=46.4ı^ N\vec{F}_{\text{net}} = (T_x - f_k)\hat{\imath} = (104.2 - 57.8)\hat{\imath} = 46.4\hat{\imath}\text{ N}.

Final answer

The applied tension exceeds the threshold of impending slip (the crate slips), and the resulting net horizontal force is F⃗net=46.4ı^ N\vec{F}_{\text{net}} = 46.4\hat{\imath}\text{ N} (or 46.4 N46.4\text{ N} in the forward direction).

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw a free-body diagram with labeled coordinate axes before writing algebraic expressions for normal force.

  • Check that any upward applied force component reduces the required support force from the ground.

  • Practice transitioning to kinetic friction whenever the applied horizontal force exceeds maximum static friction.

Lock it in

Similar question

01

A 15.0 kg15.0\text{ kg} box sits on a horizontal surface where μs=0.500\mu_s = 0.500. A pulling force of 60.0 N60.0\text{ N} is applied at an angle of 30.0∘30.0^\circ above the horizontal. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine whether the box starts moving.

Answer

Yes, it starts moving. First find N=mg−Tsin⁡(30.0∘)=(15.0)(9.80)−60.0(0.500)=147.0−30.0=117.0 NN = mg - T\sin(30.0^\circ) = (15.0)(9.80) - 60.0(0.500) = 147.0 - 30.0 = 117.0\text{ N}. The maximum static friction is fs,max⁡=0.500×117.0 N=58.5 Nf_{s,\max} = 0.500 \times 117.0\text{ N} = 58.5\text{ N}. The horizontal pulling force is Tx=60.0cos⁡(30.0∘)≈52.0 NT_x = 60.0\cos(30.0^\circ) \approx 52.0\text{ N}. Since Tx=52.0 N<58.5 NT_x = 52.0\text{ N} < 58.5\text{ N}, wait: 52.0 N<58.5 N52.0\text{ N} < 58.5\text{ N}, so it does NOT start moving. Result: No, the box remains at rest because Tx=52.0 N<fs,max⁡=58.5 NT_x = 52.0\text{ N} < f_{s,\max} = 58.5\text{ N}.

02

A 30.0 kg30.0\text{ kg} crate is pushed along a level floor by a downward diagonal force of P=150 NP = 150\text{ N} directed at 20.0∘20.0^\circ below the horizontal. If μk=0.250\mu_k = 0.250 and g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the magnitude of the normal force and the horizontal acceleration of the crate.

Answer

N=345.3 NN = 345.3\text{ N} and a=1.82 m/s2a = 1.82\text{ m/s}^2. Vertical balance: N=mg+Psin⁡(20.0∘)=(30.0)(9.80)+150sin⁡(20.0∘)=294.0+51.30=345.3 NN = mg + P\sin(20.0^\circ) = (30.0)(9.80) + 150\sin(20.0^\circ) = 294.0 + 51.30 = 345.3\text{ N}. Kinetic friction: fk=μkN=0.250(345.3)=86.33 Nf_k = \mu_k N = 0.250(345.3) = 86.33\text{ N}. Horizontal force balance: Fnet,x=Pcos⁡(20.0∘)−fk=150cos⁡(20.0∘)−86.33=140.95−86.33=54.62 NF_{\text{net},x} = P\cos(20.0^\circ) - f_k = 150\cos(20.0^\circ) - 86.33 = 140.95 - 86.33 = 54.62\text{ N}. Acceleration: a=54.62 N30.0 kg≈1.82 m/s2a = \frac{54.62\text{ N}}{30.0\text{ kg}} \approx 1.82\text{ m/s}^2.

03

A sled of mass m=18.0 kgm = 18.0\text{ kg} is pulled across horizontal snow at a constant velocity by a rope inclined at angle θ\theta above the horizontal. If the coefficient of kinetic friction is μk=0.150\mu_k = 0.150 and the tension is T=32.0 NT = 32.0\text{ N}, find the required angle θ\theta (in degrees). Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

θ≈8.5∘\theta \approx 8.5^\circ. At constant velocity, horizontal and vertical forces balance: Tcos⁡θ=fk=μkNT\cos\theta = f_k = \mu_k N and N=mg−Tsin⁡θN = mg - T\sin\theta. Substituting gives Tcos⁡θ=μk(mg−Tsin⁡θ)T\cos\theta = \mu_k (mg - T\sin\theta), so T(cos⁡θ+μksin⁡θ)=μkmgT(\cos\theta + \mu_k \sin\theta) = \mu_k mg. Evaluating the right-hand side: 0.150×18.0×9.8032.0=26.4632.0≈0.8269\frac{0.150 \times 18.0 \times 9.80}{32.0} = \frac{26.46}{32.0} \approx 0.8269. Solving cos⁡θ+0.150sin⁡θ=0.8269\cos\theta + 0.150\sin\theta = 0.8269 yields θ≈34.5∘\theta \approx 34.5^\circ (or solving Rcos⁡(θ−ϕ)=0.8269R\cos(\theta - \phi) = 0.8269 with R=1+0.152=1.0112R = \sqrt{1 + 0.15^2} = 1.0112 and ϕ=arctan⁡(0.15)=8.53∘\phi = \arctan(0.15) = 8.53^\circ, giving cos⁡(θ−8.53∘)=0.82691.0112=0.8177\cos(\theta - 8.53^\circ) = \frac{0.8269}{1.0112} = 0.8177, so θ−8.53∘=35.14∘  ⟹  θ≈43.7∘\theta - 8.53^\circ = 35.14^\circ \implies \theta \approx 43.7^\circ).

Loading workspace…