Resources

A stationary power plant engine consumes fuel oil with an energy density of 44.0 MJ/kg44.0\text{ MJ/kg} at a rate of 15.0 g/s15.0\text{ g/s}. During continuous operation, the engine delivers an output mechanical power of 231 kW231\text{ kW}. Calculate the thermal efficiency η\eta of the power plant.

Answer and steps

Final answer

η=35.0%\eta = 35.0\%

Steps

01

Convert values to consistent SI units

Thermal efficiency η\eta is defined as the ratio of useful work or power output to the total heat or energy input rate: η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}

To calculate the total input power, express both the fuel consumption rate and the energy density in standard SI units:

  • Fuel mass flow rate (m˙\dot{m}): m˙=15.0 g/s=15.0×10−3 kg/s=0.0150 kg/s\dot{m} = 15.0\text{ g/s} = 15.0 \times 10^{-3}\text{ kg/s} = 0.0150\text{ kg/s}
  • Energy density of fuel (HH): H=44.0 MJ/kg=44.0×106 J/kgH = 44.0\text{ MJ/kg} = 44.0 \times 10^6\text{ J/kg}
  • Useful output power (PoutP_{\text{out}}): Pout=231 kW=231×103 WP_{\text{out}} = 231\text{ kW} = 231 \times 10^3\text{ W}
02

Calculate the thermal power input (PinP_{\text{in}})

The rate of energy released by burning the fuel gives the power input:

Pin=m˙⋅HP_{\text{in}} = \dot{m} \cdot H

Pin=(0.0150 kg/s)⋅(44.0×106 J/kg)=6.60×105 W=660 kWP_{\text{in}} = (0.0150\text{ kg/s}) \cdot (44.0 \times 10^6\text{ J/kg}) = 6.60 \times 10^5\text{ W} = 660\text{ kW}

03

Calculate the thermal efficiency (η\eta)

Substitute PoutP_{\text{out}} and PinP_{\text{in}} into the efficiency formula:

η=231 kW660 kW=0.350\eta = \frac{231\text{ kW}}{660\text{ kW}} = 0.350

Expressed as a percentage:

η=35.0%\eta = 35.0\%

Common Pitfall: Always check mass units before multiplying rate by energy density. A common mistake is multiplying 15.0 g/s15.0\text{ g/s} directly by 44.0 MJ/kg44.0\text{ MJ/kg} without converting grams to kilograms, which leads to an input power that is incorrect by a factor of 10001000.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the fuel consumption rate from grams per second to kilograms per second, overestimating input power by a factor of 1000 and yielding an efficiency that is too small by 10^3.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pin=(15.0)⋅(44.0 MJ/s)  ⟹  Pin=660 MW=660000 kWP_{\text{in}} = (15.0) \cdot (44.0\text{ MJ/s}) \implies P_{\text{in}} = 660\text{ MW} = 660000\text{ kW}

    Correct

    Pin=m˙⋅H=(15.0×10−3 kg/s)⋅(44.0 MJ/kg)=0.660 MW=660 kWP_{\text{in}} = \dot{m} \cdot H = (15.0 \times 10^{-3}\text{ kg/s}) \cdot (44.0\text{ MJ/kg}) = 0.660\text{ MW} = 660\text{ kW}

    You multiplied the mass flow rate of 15.0 g/s15.0\text{ g/s} directly by the energy density 44.0 MJ/kg44.0\text{ MJ/kg} without converting grams to kilograms. Since 1 g=10−3 kg1\text{ g} = 10^{-3}\text{ kg}, the actual input power is 0.660 MW0.660\text{ MW} (660 kW660\text{ kW}), not 660 MW660\text{ MW}.

  2. Step 2

    η=PoutPin=231 kW660000 kW=0.035%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{231\text{ kW}}{660000\text{ kW}} = 0.035\%

    Correct

    η=PoutPin=231 kW660 kW=0.350=35.0%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{231\text{ kW}}{660\text{ kW}} = 0.350 = 35.0\%

    You correctly applied the definition η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}} and converted your ratio to a percentage, but your result was affected by the input power error from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that thermal efficiency is the ratio of output power to input power, η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}.

You correctly converted megawatts to kilowatts by multiplying by 10001000.

You converted your decimal ratio into a percentage correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing metric prefix conversion (grams to kilograms)

You substituted 15.0 g/s15.0\text{ g/s} as if it were in kilograms per second when calculating input power.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking unit consistency between mass flow rate (expressed in grams) and specific energy density (expressed per kilogram). Multiplying g/s\text{g/s} by MJ/kg\text{MJ/kg} yields kJ/s\text{kJ/s} (or kW\text{kW}), not MW\text{MW}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Mass Base Units
  • Before multiplying a flow rate m˙\dot{m} by a specific energy HH, verify that their mass units cancel out directly: kg/s×J/kg=J/s=W\text{kg/s} \times \text{J/kg} = \text{J/s} = \text{W}.

  • Always convert grams to kilograms (1 g=10−3 kg1\text{ g} = 10^{-3}\text{ kg}) before substituting into formulas containing kilograms.

Reasonableness Check for Thermal Efficiency
  • Practical thermal power plants and heat engines typically operate at efficiencies between 20%20\% and 50%50\%.

  • If your calculated efficiency is an extreme value like 0.035%0.035\%, check for a factor-of-10001000 unit conversion error in power or mass.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the mass flow rate to standard SI units: m˙=15.0 g/s=0.0150 kg/s\dot{m} = 15.0\text{ g/s} = 0.0150\text{ kg/s}.

  2. Calculate the input thermal power: Pin=(0.0150 kg/s)⋅(44.0×106 J/kg)=6.60×105 W=660 kWP_{\text{in}} = (0.0150\text{ kg/s}) \cdot (44.0 \times 10^6\text{ J/kg}) = 6.60 \times 10^5\text{ W} = 660\text{ kW}.

  3. Substitute into the efficiency formula: η=PoutPin=231 kW660 kW=0.350\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{231\text{ kW}}{660\text{ kW}} = 0.350.

Final answer

η=35.0%\eta = 35.0\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out complete units during intermediate steps to ensure mass units (extg ext{g} vs. extkg ext{kg}) cancel properly.

  • Perform a quick sanity check: an engine efficiency of 0.035%0.035\% is unrealistically low for a modern power plant.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the ratio in the efficiency formula by dividing input power by output power instead of output power by input power.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    dmdt=15.0 g/s=0.0150 kg/s  ⟹  Pin=0.0150 kg/s×44.0 MJ/kg=0.660 MJ/s=660 kW\frac{dm}{dt} = 15.0\text{ g/s} = 0.0150\text{ kg/s} \implies P_{\text{in}} = 0.0150\text{ kg/s} \times 44.0\text{ MJ/kg} = 0.660\text{ MJ/s} = 660\text{ kW}

  2. Step 2

    η=PinPout  ⟹  η=660 kW231 kW\eta = \frac{P_{\text{in}}}{P_{\text{out}}} \implies \eta = \frac{660\text{ kW}}{231\text{ kW}}

    Correct

    η=PoutPin=231 kW660 kW\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{231\text{ kW}}{660\text{ kW}}

    Thermal efficiency is defined as the ratio of useful output power to total input power (η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}), but you inverted this fraction.

  3. Step 3

    η=2.86\eta = 2.86

    Correct

    η=0.350=35.0%\eta = 0.350 = 35.0\%

    Your numerical division followed your inverted formula, resulting in an efficiency greater than 100%100\%.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted the mass flow rate from grams per second to kilograms per second correctly.

You multiplied the mass flow rate by the specific energy density to obtain the correct input power of 660 kW660\text{ kW}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted efficiency ratio

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defined efficiency as input power divided by output power rather than useful work output divided by total energy input, which physically implies an impossible efficiency exceeding 100%.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Efficiency
  • η=What you get (useful)What you pay (total input)=PoutPin\eta = \frac{\text{What you get (useful)}}{\text{What you pay (total input)}} = \frac{P_{\text{out}}}{P_{\text{in}}}

  • Always place the useful energy or power produced in the numerator and the total energy consumed in the denominator.

Sanity Check for Real Engines
  • According to the Second Law of Thermodynamics and conservation of energy, the thermal efficiency of any real engine must satisfy 0<η<10 < \eta < 1 (0%<η<100%0\% < \eta < 100\%).

  • If your calculated efficiency is greater than 11, immediately invert the fraction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the standard efficiency formula: η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}.

  2. Substitute Pout=231 kWP_{\text{out}} = 231\text{ kW} and Pin=660 kWP_{\text{in}} = 660\text{ kW}: η=231 kW660 kW\eta = \frac{231\text{ kW}}{660\text{ kW}}.

  3. Simplify the fraction: η=0.350=35.0%\eta = 0.350 = 35.0\%.

Final answer

η=35.0%\eta = 35.0\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the efficiency ratio as 'useful output over total input'.

  • Perform a sanity check at the end of every efficiency problem to verify that η≤1\eta \le 1.

OverviewACEpath Teacher's Diagnosis

03 The student calculates efficiency relative to energy loss by dividing output power by the difference between input and output power.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pin=0.0150 kg/s×44.0×103 kJ/kg=660 kWP_{\text{in}} = 0.0150\text{ kg/s} \times 44.0 \times 10^3\text{ kJ/kg} = 660\text{ kW}

  2. Step 2

    Ploss=660 kW−231 kW=429 kWP_{\text{loss}} = 660\text{ kW} - 231\text{ kW} = 429\text{ kW}

  3. Step 3

    η=PoutPloss  ⟹  η=231 kW429 kW=0.538\eta = \frac{P_{\text{out}}}{P_{\text{loss}}} \implies \eta = \frac{231\text{ kW}}{429\text{ kW}} = 0.538

    Correct

    η=PoutPin=231 kW660 kW=0.350 (or 35.0%)\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{231\text{ kW}}{660\text{ kW}} = 0.350\text{ (or } 35.0\%)

    Thermal efficiency is defined as the ratio of useful power output to total input power (Pout/PinP_{\text{out}} / P_{\text{in}}), not power lost (Pout/PlossP_{\text{out}} / P_{\text{loss}}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the mass consumption rate to kg/s\text{kg/s} and determined the thermal power input as 660 kW660\text{ kW}.

You correctly calculated the waste heat power using energy conservation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect efficiency formula denominator

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You divided the useful power output by the wasted power (PlossP_{\text{loss}}) instead of dividing by the total supplied power (PinP_{\text{in}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Thermal Efficiency
  • Thermal efficiency measures what fraction of the total supplied energy becomes useful work: η=useful outputtotal input=PoutPin\eta = \frac{\text{useful output}}{\text{total input}} = \frac{P_{\text{out}}}{P_{\text{in}}}.

  • Always place the total energy or power supplied into the denominator, ensuring η≤1\eta \le 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the definition of thermal efficiency: η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}.

  2. Substitute the given useful output power and the calculated input power: η=231 kW660 kW\eta = \frac{231\text{ kW}}{660\text{ kW}}.

  3. Simplify the fraction: η=0.350=35.0%\eta = 0.350 = 35.0\%.

Final answer

η=35.0%\eta = 35.0\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that efficiency is always 'what you get out' divided by 'what you put in', never divided by 'what you lose'.

  • Practice checking that the denominator represents the whole original energy input so the resulting efficiency cannot exceed 100%100\%.

Lock it in

Similar question

01

A diesel generator consumes fuel with an energy density of 42.0 MJ/kg42.0\text{ MJ/kg} at a rate of 20.0 g/s20.0\text{ g/s}. If the generator produces 336 kW336\text{ kW} of electrical power, what is its thermal efficiency?

Answer

40.0%40.0\%. Key steps: convert m˙=0.0200 kg/s\dot{m} = 0.0200\text{ kg/s}; compute Pin=0.0200 kg/s×42.0 MJ/kg=0.840 MW=840 kWP_{\text{in}} = 0.0200\text{ kg/s} \times 42.0\text{ MJ/kg} = 0.840\text{ MW} = 840\text{ kW}; calculate η=336 kW840 kW=0.400=40.0%\eta = \frac{336\text{ kW}}{840\text{ kW}} = 0.400 = 40.0\%.

02

An industrial boiler burns natural gas with an energy density of 50.0 MJ/kg50.0\text{ MJ/kg} at a rate of 144 kg/h144\text{ kg/h}. It delivers useful heat output at a rate of 1.60 MW1.60\text{ MW}. Find the thermal efficiency of the boiler.

Answer

80.0%80.0\%. Key steps: convert fuel rate to per second: m˙=144 kg3600 s=0.0400 kg/s\dot{m} = \frac{144\text{ kg}}{3600\text{ s}} = 0.0400\text{ kg/s}; compute Pin=0.0400 kg/s×50.0 MJ/kg=2.00 MWP_{\text{in}} = 0.0400\text{ kg/s} \times 50.0\text{ MJ/kg} = 2.00\text{ MW}; calculate η=1.60 MW2.00 MW=0.800=80.0%\eta = \frac{1.60\text{ MW}}{2.00\text{ MW}} = 0.800 = 80.0\%.

03

A gas turbine operates with a thermal efficiency of 32.0%32.0\% and delivers a mechanical power output of 480 kW480\text{ kW}. If the fuel has an energy density of 45.0 MJ/kg45.0\text{ MJ/kg}, calculate the required fuel consumption rate in g/s\text{g/s}.

Answer

33.3 g/s33.3\text{ g/s}. Key steps: find required input power Pin=Poutη=480 kW0.320=1500 kWP_{\text{in}} = \frac{P_{\text{out}}}{\eta} = \frac{480\text{ kW}}{0.320} = 1500\text{ kW}; determine mass flow rate m˙=1500 kW45000 kJ/kg=130 kg/s≈0.0333 kg/s\dot{m} = \frac{1500\text{ kW}}{45000\text{ kJ/kg}} = \frac{1}{30}\text{ kg/s} \approx 0.0333\text{ kg/s}; convert to grams per second: 0.0333 kg/s×1000=33.3 g/s0.0333\text{ kg/s} \times 1000 = 33.3\text{ g/s}.

Loading workspace…