Resources
A uniform horizontal shelf of length and mass is hinged to a vertical wall at its left end and supported at its right end by a support cable under a fixed tension of . A crate of mass is placed at a distance from the hinge. Determine the angle that the support cable must make above the horizontal for the shelf to maintain static rotational equilibrium. Assume .
Answer and steps
Final answer
Steps
Identify the Torques Acting on the Shelf
To find the required angle , we apply the condition of static rotational equilibrium to the shelf.
Choosing the hinge at the left end as the pivot point eliminates the unknown reaction forces exerted by the hinge, as their lines of action pass directly through the pivot (lever arm is zero).
Taking counterclockwise torques as positive and clockwise torques as negative:
- Torque due to the shelf's weight (): The shelf is uniform, so its center of gravity is at its geometric center, .
- Torque due to the crate's weight (): The crate rests at a distance from the hinge.
- Torque due to the cable tension (): The cable attaches to the right end at distance and pulls at an angle above the shelf. The component of tension perpendicular to the shelf is , exerting a counterclockwise torque:
Apply the Rotational Equilibrium Condition
For the shelf to remain in rotational equilibrium, the sum of all torques about the hinge must equal zero:
Solve for the Angle
Isolating :
Taking the inverse sine:
(Note: A common pitfall is forgetting that the uniform shelf's weight acts at its midpoint , rather than at the right end .)
Typical errors
01 The student treats the shelf's weight as acting at its full length rather than at its center of mass, leading to an overestimated torque and an incorrect angle.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the shelf is uniform, its weight acts at its center of mass, which is at the geometric midpoint from the hinge, rather than at the far end .
- Step 2Correct
This step carries through the arithmetic correctly based on your equation, but it uses the doubled lever arm for the shelf's weight from Step 1.
- Step 3Correct
Your algebraic rearrangement and inverse sine calculation are executed correctly, but they yield an incorrect angle due to the overestimated torque.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly chose the hinge as the pivot point to eliminate the unknown wall reaction forces.
You properly resolved the cable tension into its perpendicular component at distance .
You correctly calculated the clockwise torque exerted by the crate's weight at distance .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the uniform shelf's gravitational force as acting at its endpoint instead of at its center of gravity . For any uniform rigid body in a uniform gravitational field, the weight acts through the center of mass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Locate the Center of Gravity
For a uniform beam or shelf of length , the weight acts at the geometric midpoint: .
Whenever an object has mass distributed uniformly along its length, draw the weight vector directly downward from before writing the torque equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the correct torque equilibrium about the hinge: .
Substitute the values: .
Simplify both sides: .
Isolate : .
Compute the angle: .
02 The student uses cos(θ) instead of sin(θ) for the torque exerted by the support cable, confusing the horizontal and vertical components.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the shelf lies along the horizontal and the cable pulls at an angle above the horizontal, the component of tension perpendicular to the shelf is . The horizontal component acts parallel to the shelf and points directly toward the pivot, producing zero torque.
- Step 2Correct
Your arithmetic and substitutions for the weights and lever arms are completely correct, but the expression carries forward the incorrect trigonometric function.
- Step 3Correct
You correctly solved for the angle from your equation, but because was used instead of , your final angle is the complement of the correct angle.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set the net torque about the hinge equal to zero.
You placed the shelf's gravitational force at its geometric midpoint .
You substituted all given physical values and performed the algebraic steps accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou selected the cosine component rather than the sine component when computing torque, overlooking that torque is generated only by the force component perpendicular to the lever arm ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Perpendicular Force for Torque
, where is the angle between the position vector and the force vector .
Always draw the right triangle resolving the force into components parallel and perpendicular to the beam before writing the torque equation.
- Zero Torque Along Line of Action
Any force component directed along or through the pivot line has a lever arm of zero and exerts no torque.
Check that your chosen component does not point directly through the hinge.
CORRECTED PATH
ACEpath Teacher's Demonstration03 The student completely omits the torque due to the weight of the shelf itself, accounting only for the crate.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You recognized that the sum of torques about the hinge must equal zero, but you omitted the torque caused by the shelf's own mass (), which acts downwards at its center of mass ().
- Step 2Correct
Your algebra and numerical substitutions were evaluated correctly based on your equation, but the result is missing the torque from the shelf.
- Step 3Correct
You correctly took the inverse sine of your calculated value, but the angle is too small because the missing torque was not accounted for.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly chose the hinge as the pivot point to eliminate unknown hinge reaction forces.
You accurately found the perpendicular lever arm and torque contribution from the cable tension.
You accurately calculated the torque exerted by the hanging crate.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the shelf as an ideal massless rod instead of accounting for its distributed mass () acting at its center of gravity.
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for Non-Massless Supports
Whenever an extended body has a given mass , gravity exerts a downward force at its center of mass.
Draw a free-body diagram and always include the object's own weight vector at its geometric midpoint if the object is uniform.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the torque of the shelf about the hinge: .
Set the net torque to zero: .
Solve for the angle: .
Lock it in
Where does gravity act on a uniform rod of length when calculating torques?
At its center of mass, exactly at the midpoint from either end.
Similar question
A uniform horizontal beam of length and mass is hinged to a wall at its left end and held horizontally by a vertical cable attached at its right end. Calculate the tension in the cable. (Assume )
Answer
. Key step: Take torques about the hinge: .
A uniform plank of length and mass is hinged at the left end and supported by a cable at the right end angled at above the horizontal. A person of mass stands at from the hinge. Find the tension in the cable. (Assume )
Answer
(or ). Key step: About the hinge, . Here , so .
A uniform boom of length and mass is hinged at its base and held at an angle of above the horizontal by a horizontal tie-rope connected to the top end. A load of mass hangs from the top end. Determine the tension in the horizontal rope. (Assume )
Answer
(or ). Key step: About the hinge, the counterclockwise torque is from the rope: . Clockwise torques come from the boom's weight at and the load at : . Dividing by yields .