Resources
In a physics experiment coupling calorimetry and electrical circuits, an immersion heating coil of resistance is placed in a thermally insulated container holding of pure liquid water with specific heat capacity . A constant current passes through the resistor. The water temperature is recorded as a function of elapsed time :
Assuming negligible heat capacity of the vessel and zero thermal dissipation to the surroundings, evaluate the rate of temperature increase from the linear trend, calculate the electric power delivered to the water, and determine the resistance of the coil.
Answer and steps
Final answer
; ;
Steps
Determine the rate of temperature rise ()
From the given data table, examine the change in temperature over equal time intervals :
- From to :
- From to :
- From to :
- From to :
Because the temperature changes by a constant amount in every equal interval, the relationship is perfectly linear. Calculate the slope:
Calculate the thermal power delivered to the water ()
The heat energy absorbed by the water of mass to produce a temperature change is given by:
Differentiating with respect to time gives the rate of thermal energy transfer (heating power ):
Substitute the known parameters (, , and ):
Determine the resistance of the heating coil ()
Assuming complete conversion of electrical energy into thermal energy inside the insulated container, the electrical power dissipated by the resistor is related to current and resistance via Joule's law:
Rearrange to solve for :
Substitute and :
Typical errors
01 The student forgets to square the current when calculating resistance from power using the formula P = I*R instead of P = I²R.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You used the relation instead of Joule's law . Because electrical power is current times voltage () and Ohm's law states , substituting gives .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the constant rate of temperature increase using endpoints from the table.
You accurately converted the temperature rate into thermal power using .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated Ohm's law for electric potential difference () with Joule's law for dissipated electric power (), omitting the square on current.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check power formulas against fundamental definitions
Electric power delivered by a resistor is , whereas Ohm's law is .
Always verify that your power formula contains a squared term when only current or voltage is given alongside resistance.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply Joule's law relating electrical power to current and resistance: .
Rearrange to solve for resistance: .
Substitute and : .
02 The student inappropriately converts the mass of water from grams to kilograms while keeping the specific heat capacity in J/(g·°C), leading to a power underestimated by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You converted the mass to , but the specific heat capacity was provided in . Because the mass unit in is grams, the mass must either remain in grams () or must be converted to .
- Step 3Correct
You correctly applied Joule's law to solve for , but your final numerical answer was affected by the power error from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the slope from the table values.
You selected the correct physical formulas connecting thermal rate of change to power and electrical dissipation.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou automatically converted mass to kilograms without checking the units of the given specific heat constant.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking unit compatibility in compound physical constants ( in vs. mass in ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Alignment Check
Before multiplying mass and specific heat , cancel units explicitly: .
Always verify whether is given per gram or per kilogram before converting mass.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute and into :
Substitute into :
, ,
03 The student calculates the temperature rate of increase by taking the inverse slope dt/dT instead of dT/dt.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You inverted the rate of change by placing time change in the numerator and temperature change in the denominator, computing instead of .
- Step 2Correct
Your thermal power formula is completely correct, but substituting your inverted temperature rate propagated an incorrect power value.
- Step 3Correct
You correctly applied Joule's law to solve for resistance, but the value is affected by the earlier power calculation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the rate of heat absorption relates to temperature rate of change via .
You correctly applied Joule's law and rearranged it accurately to solve for resistance .
You executed the arithmetic calculations reliably based on your written numbers.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou swapped the dependent and independent variables in the slope ratio, computing elapsed time per degree change () rather than degrees per second ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Rate of Change Definition
For any derivative or rate , the change in the dependent variable must be in the numerator, and the change in the independent variable must be in the denominator: .
Always verify the units of your slope against the symbol: has units of , meaning temperature units must be on top and seconds on the bottom.
- Order of Magnitude Sense Check
A temperature rise of means water heats by over in six seconds, which requires industrial levels of power () far beyond a typical bench circuit.
Pause to check whether your rate matches the table: the water only warmed by over an entire , which clearly means much less than per second.
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What is the formula relating electric power to current and resistance in a resistor?
. (Derived from combined with Ohm's law .)
Similar question
An immersion heater carrying a current of warms a fluid at an absorbed power rate of . Calculate the electrical resistance of the immersion heater.
Answer
. Using Joule's law: .
A sample of water () in an insulated calorimeter heats up at a constant rate of when powered by a current of . Find the thermal power delivered and the resistance of the coil.
Answer
and . Thermal power is . Coil resistance is .
A heating resistor of unknown value is submerged in of liquid (). When connected to a constant-voltage source, the temperature rises uniformly from to in . Determine the thermal power , the current , and the resistance .
Answer
, , and . First, calculate power from calorimetry: . Resistance from voltage is . The current is (or ).