Resources
In a microscopic semiconductor channel of length , parallel metallic contacts establish a potential difference measured in millivolts: the left contact at is held at , and the right contact at is held at . Equipotential surfaces run perpendicular to the channel axis with an incremental step of . (a) Convert the total potential difference to volts and channel length to meters, then calculate the magnitude of the uniform electric field in kilovolts per centimeter () and megavolts per meter (). (b) Calculate the spacing between consecutive equipotential surfaces in nanometers (). (c) Calculate the magnitude of the electrostatic force acting on a conduction electron () within this channel in piconewtons ().
Answer and steps
Final answer
(a) , , ; (b) ; (c)
Steps
Part (a): Total Potential Difference, Channel Length, and Electric Field Magnitude
-
Convert the given quantities into SI base units:
- The potential at the left contact is:
- The potential at the right contact is:
- The total potential difference across the channel is:
- The channel length in meters is:
- Calculate the magnitude of the uniform electric field : In a uniform electric field, the magnitude of the field is the potential gradient:
-
Convert to the requested units:
- In megavolts per meter (), where :
- In kilovolts per centimeter (), where and :
Part (b): Spacing Between Consecutive Equipotential Surfaces
Equipotential surfaces are planes perpendicular to the uniform electric field lines. For a uniform field, the potential changes linearly with distance:
Solving for the spatial interval corresponding to an incremental drop of :
Convert this spacing to nanometers:
(Note: Alternatively, since the field is uniform, the fraction of length is simply the ratio of potentials: .)
Part (c): Magnitude of the Electrostatic Force on an Electron
The magnitude of the electrostatic force acting on a charged particle of charge magnitude in an electric field is given by:
Substitute and :
Convert the force from newtons to piconewtons (), where :
Typical errors
01 A student incorrectly subtracts the potential values without accounting for the negative sign of V_2, finding ΔV_total = 500 mV instead of 1200 mV, which propagates through the rest of the problem.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The potential at the right boundary is negative (). Subtracting a negative potential gives , rather than .
- Step 2Correct
Your formula and your unit conversions to and were executed correctly, but the numerical value was affected by your earlier potential difference.
- Step 3Correct
You correctly applied the relationship and converted meters to nanometers, but your result inherits the incorrect value of .
- Step 4Correct
You applied and converted newtons to piconewtons accurately, but using caused your final force to be too small.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted length from nanometers to meters ().
You correctly applied the relationship for a uniform electric field.
You handled multi-unit conversions into , , and with solid algebraic precision.
You correctly identified that the equipotential spacing satisfies and that electric force satisfies .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the magnitude of the negative potential as a positive value inside the subtraction , overlooking that subtracting a negative number adds its absolute value: .
REASONING PATH
Your ACEpath teacher’s suggested approach- Substitute Directed Quantities with Parentheses
or . When any potential is negative, substitute it within parentheses: .
Always write explicitly before simplifying to ensure the double negative becomes an addition.
- Number Line Sanity Check
Moving from a positive potential to a negative potential spans across zero, so the total potential drop must be larger than either individual contact potential.
Check that whenever and have opposite signs.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) , , ; (b) ; (c)
02 A student misconverts the metric prefix when transforming the electric field to kV/cm by incorrectly multiplying by 100 instead of dividing by 100.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because meters are in the denominator of , replacing with means you must divide by , not multiply. This gives .
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly handled the sign difference when calculating the total voltage across the channel.
You applied the uniform electric field formula accurately.
You correctly calculated both the equipotential contour spacing and the electrostatic force on the electron.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up the conversion factor with meters in the denominator, but multiplied by instead of placing in the denominator to cancel meters.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInverting conversion factors when transforming compound units where the target unit appears in the denominator ( to ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Denominator Unit Substitution
When converting a unit in the denominator, substitute the identity directly into the denominator: .
Write out the denominator substitution explicitly: .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute :
(a) , , ; (b) ; (c)
03 A student confuses the unit prefix piconewtons (10⁻¹² N) with femtonewtons (10⁻¹⁵ N), resulting in an electrostatic force of 256 pN instead of 0.256 pN.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You used for one piconewton instead of . The prefix pico (p) denotes , whereas corresponds to femto (f).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the total potential difference across the semiconductor channel, taking proper care of the negative potential at the right boundary.
You correctly determined the uniform electric field magnitude and executed the unit conversions to MV/m and kV/cm.
You correctly used the field equation to find the spatial separation between equipotential surfaces.
You correctly multiplied the elementary charge by the field strength to get the electrostatic force in newtons.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted instead of when converting newtons to piconewtons.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the metric prefix 'pico-' () with 'femto-' (), leading to an answer that is three orders of magnitude too large.
REASONING PATH
Your ACEpath teacher’s suggested approach- Metric Prefixes in Sub-Microscopic Physics
The standard metric prefixes decrease in steps of : milli (), micro (), nano (), pico (), and femto ().
Always recall that pico- is (), so converting from newtons to piconewtons means dividing by .
CORRECTED PATH
ACEpath Teacher's DemonstrationState the conversion factor between newtons and piconewtons: .
Convert by dividing by :
Round to three significant figures to match the given data: .
Lock it in
How do you find the potential difference when and ?
. Subtracting a negative value increases the total difference.
Similar question
Two parallel electrodes separated by are held at and . Find the magnitude of the uniform electric field in .
Answer
The potential difference is . Converting distance to meters gives . Thus, .
In a nanoscale junction of length , the left terminal is at and the right terminal is at . If equipotential surfaces are plotted every , calculate the physical distance between adjacent surfaces in nanometers.
Answer
The total potential difference is . Since the electric field is uniform, the spacing is proportional to potential: .
A singly charged ion () moves through a gap between plates biased at and . Calculate: (1) the electric field magnitude in , and (2) the magnitude of the electrostatic force on the ion in piconewtons ().
Answer
(1) . With , . (2) .