Resources

A vertical cylindrical hydraulic chamber of inner diameter D=0.250 mD = 0.250\text{ m} is sealed at the top by a piston. The wall of the cylinder has an allowable maximum internal gauge pressure threshold of Pgauge, max=4.50×105 PaP_{\text{gauge, max}} = 4.50 \times 10^5\text{ Pa} before plastic deformation occurs. Determine the critical threshold mass mcritm_{\text{crit}} of the piston (in kilograms) that would cause the fluid directly beneath the piston face to just reach this maximum allowable gauge pressure limit, assuming atmospheric pressure acts uniformly on the outer piston face and g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

mcrit=2.26×103 kgm_{\text{crit}} = 2.26 \times 10^3\text{ kg}

Steps

01

Relate Pressure and Force on the Piston

Gauge pressure represents the pressure of a system relative to the local atmospheric pressure: Pgauge=Pabs−PatmP_{\text{gauge}} = P_{\text{abs}} - P_{\text{atm}}

Consider the vertical forces acting on the piston of mass mcritm_{\text{crit}} and cross-sectional area AA in static equilibrium:

  • Downward forces:
    • Atmospheric force acting on the top surface: Fatm=PatmAF_{\text{atm}} = P_{\text{atm}} A
    • Weight of the piston: W=mcritgW = m_{\text{crit}} g
  • Upward force:
    • Force exerted by the hydraulic fluid on the bottom surface: Ffluid=PabsAF_{\text{fluid}} = P_{\text{abs}} A

Setting the sum of vertical forces to zero: Ffluid−Fatm−W=0F_{\text{fluid}} - F_{\text{atm}} - W = 0 (Pabs−Patm)A=mcritg(P_{\text{abs}} - P_{\text{atm}}) A = m_{\text{crit}} g

Since Pabs−Patm=PgaugeP_{\text{abs}} - P_{\text{atm}} = P_{\text{gauge}}, the equation simplifies directly to: PgaugeA=mcritgP_{\text{gauge}} A = m_{\text{crit}} g

Key Pitfall: A common mistake is using the absolute pressure instead of the gauge pressure to determine the weight of the piston. Because atmospheric pressure acts equally on the outside of the piston, its effect cancels out, meaning the excess (gauge) pressure inside the chamber is generated entirely by the weight of the piston.


02

Calculate the Cross-Sectional Area

The piston has a circular cross-section of inner diameter D=0.250 mD = 0.250\text{ m}: A=πD24A = \frac{\pi D^2}{4} A=π(0.250 m)24≈4.9087×10−2 m2A = \frac{\pi (0.250\text{ m})^2}{4} \approx 4.9087 \times 10^{-2}\text{ m}^2


03

Calculate the Critical Mass

Rearranging the equilibrium equation for the critical threshold mass mcritm_{\text{crit}} gives: mcrit=Pgauge, maxAgm_{\text{crit}} = \frac{P_{\text{gauge, max}} A}{g}

Substitute the given numerical values: mcrit=(4.50×105 Pa)(4.9087×10−2 m2)9.80 m/s2m_{\text{crit}} = \frac{(4.50 \times 10^5\text{ Pa})(4.9087 \times 10^{-2}\text{ m}^2)}{9.80\text{ m/s}^2} mcrit=2.2089×104 N9.80 m/s2≈2.254×103 kgm_{\text{crit}} = \frac{2.2089 \times 10^4\text{ N}}{9.80\text{ m/s}^2} \approx 2.254 \times 10^3\text{ kg}

Rounding to three significant figures gives: mcrit=2.26×103 kgm_{\text{crit}} = 2.26 \times 10^3\text{ kg}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the diameter instead of the radius in the area formula πr², overestimating the area by a factor of 4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=π⋅D2=π(0.250)2≈0.1963 m2A = \pi \cdot D^2 = \pi (0.250)^2 \approx 0.1963\text{ m}^2

    Correct

    A=πD24=π(0.250)24≈4.909×10−2 m2A = \frac{\pi D^2}{4} = \frac{\pi (0.250)^2}{4} \approx 4.909 \times 10^{-2}\text{ m}^2

    You used the diameter DD directly in place of the radius in πr2\pi r^2, omitting the division by 44 (or halving the diameter to radius r=0.125 mr = 0.125\text{ m}).

  2. Step 2

    Pgauge=m⋅gAP_{\text{gauge}} = \frac{m \cdot g}{A}

  3. Step 3

    m=Pgauge⋅Ag=(4.50×105)(0.1963)9.80≈9014 kgm = \frac{P_{\text{gauge}} \cdot A}{g} = \frac{(4.50 \times 10^5)(0.1963)}{9.80} \approx 9014\text{ kg}

    Correct

    m=Pgauge⋅Ag=(4.50×105)(4.9087×10−2)9.80≈2.26×103 kgm = \frac{P_{\text{gauge}} \cdot A}{g} = \frac{(4.50 \times 10^5)(4.9087 \times 10^{-2})}{9.80} \approx 2.26 \times 10^3\text{ kg}

    Your algebraic rearrangement and calculation were carried out correctly, but the result was multiplied by 44 because of the area error from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that atmospheric pressure cancels on both sides of the piston, leaving PgaugeA=mgP_{\text{gauge}} A = mg.

You correctly rearranged the equilibrium relation to solve for the critical mass mm.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Area formula confusion with diameter

You treated the given diameter as a radius when squaring, writing πD2\pi D^2 instead of πD24\frac{\pi D^2}{4}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating circle area formulas expressed in terms of radius (A=πr2A = \pi r^2) and diameter (A=πD24A = \frac{\pi D^2}{4}). Because r=D2r = \frac{D}{2}, squaring DD without dividing by 44 overestimates the area by a factor of 22=42^2 = 4.

REASONING PATH
Your ACEpath teacher’s suggested approach
Area from Diameter Check
  • A=πr2=π(D2)2=πD24A = \pi r^2 = \pi \left(\frac{D}{2}\right)^2 = \frac{\pi D^2}{4}

  • Whenever a problem provides a diameter DD, immediately write down r=D2r = \frac{D}{2} before computing, or use πD24\frac{\pi D^2}{4}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct circular cross-sectional area: A=π(0.250 m)24≈4.9087×10−2 m2A = \frac{\pi (0.250\text{ m})^2}{4} \approx 4.9087 \times 10^{-2}\text{ m}^2

  2. Substitute into your rearranged mass formula: m=(4.50×105 Pa)(4.9087×10−2 m2)9.80 m/s2m = \frac{(4.50 \times 10^5\text{ Pa})(4.9087 \times 10^{-2}\text{ m}^2)}{9.80\text{ m/s}^2}

  3. Evaluate the numerical value: m≈2.254×103 kg≈2.26×103 kgm \approx 2.254 \times 10^3\text{ kg} \approx 2.26 \times 10^3\text{ kg}

Final answer

mcrit=2.26×103 kgm_{\text{crit}} = 2.26 \times 10^3\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Convert diameters to radii as your very first recorded step when solving geometry and pressure problems.

  • Re-evaluate your final numerical answers using dimensional analysis and order-of-magnitude estimates to ensure geometric scaling factors like r2r^2 vs D2D^2 are not missed.

OverviewACEpath Teacher's Diagnosis

02 The student confuses gauge pressure with absolute pressure and unnecessarily adds atmospheric pressure (1.013 × 10⁵ Pa) to the force balance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=0.2502=0.125 m  ⟹  A=π⋅(0.125)2≈0.04909 m2r = \frac{0.250}{2} = 0.125\text{ m} \implies A = \pi \cdot (0.125)^2 \approx 0.04909\text{ m}^2

  2. Step 2

    Pabs=Pgauge+Patm=4.50×105+1.013×105=5.513×105 Pa  ⟹  m=Pabs⋅AgP_{\text{abs}} = P_{\text{gauge}} + P_{\text{atm}} = 4.50 \times 10^5 + 1.013 \times 10^5 = 5.513 \times 10^5\text{ Pa} \implies m = \frac{P_{\text{abs}} \cdot A}{g}

    Correct

    ΣFy=0  ⟹  PabsA−PatmA−mg=0  ⟹  m=(Pabs−Patm)Ag=PgaugeAg\Sigma F_y = 0 \implies P_{\text{abs}} A - P_{\text{atm}} A - m g = 0 \implies m = \frac{(P_{\text{abs}} - P_{\text{atm}}) A}{g} = \frac{P_{\text{gauge}} A}{g}

    You included atmospheric pressure in the net lifting force. Atmospheric pressure acts downward on the outer face with force PatmAP_{\text{atm}} A and upward from the fluid through PabsA=(Patm+Pgauge)AP_{\text{abs}} A = (P_{\text{atm}} + P_{\text{gauge}}) A. The atmospheric terms cancel out, leaving only PgaugeA=mgP_{\text{gauge}} A = m g.

  3. Step 3

    m=(5.513×105)(0.04909)9.80≈2762 kgm = \frac{(5.513 \times 10^5)(0.04909)}{9.80} \approx 2762\text{ kg}

    Correct

    m=(4.50×105 Pa)(4.909×10−2 m2)9.80 m/s2≈2.26×103 kgm = \frac{(4.50 \times 10^5\text{ Pa})(4.909 \times 10^{-2}\text{ m}^2)}{9.80\text{ m/s}^2} \approx 2.26 \times 10^3\text{ kg}

    Your arithmetic follows your formula correctly, but the result is too large because it was calculated using absolute pressure.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly found the cross-sectional area from the given diameter.

You correctly identified the standard relation between absolute pressure, gauge pressure, and atmospheric pressure.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating gauge and absolute pressure in force balances

None. This is a conceptual error regarding how surrounding atmospheric pressure affects boundary equilibrium.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When setting up static equilibrium for an object exposed to ambient air on one side and a pressurized fluid on the other, you accounted for the fluid's total absolute pressure without including the downward atmospheric force PatmAP_{\text{atm}} A acting on the top surface. This led you to equate mgm g to PabsAP_{\text{abs}} A instead of the net pressure force (Pabs−Patm)A=PgaugeA(P_{\text{abs}} - P_{\text{atm}}) A = P_{\text{gauge}} A.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify external atmospheric force
  • If a piston is exposed to the atmosphere on its outside face, air exerts a downward force equal to Fatm=PatmAF_{\text{atm}} = P_{\text{atm}} A.

  • Always draw a free-body diagram showing FatmF_{\text{atm}} downward, weight mgm g downward, and Ffluid=PabsAF_{\text{fluid}} = P_{\text{abs}} A upward.

Cancel uniform atmospheric pressure
  • Fnet, pressure=(Pabs−Patm)A=PgaugeAF_{\text{net, pressure}} = (P_{\text{abs}} - P_{\text{atm}}) A = P_{\text{gauge}} A.

  • Substitute PgaugeP_{\text{gauge}} directly into the equilibrium equation when the opposite side is open to local atmospheric pressure.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the vertical static equilibrium equation for the piston: Ffluid−Fatm−mg=0F_{\text{fluid}} - F_{\text{atm}} - m g = 0.

  2. Express the forces in terms of pressures: PabsA−PatmA=mgP_{\text{abs}} A - P_{\text{atm}} A = m g.

  3. Factor out the area and recognize gauge pressure: (Pabs−Patm)A=PgaugeA=mg(P_{\text{abs}} - P_{\text{atm}}) A = P_{\text{gauge}} A = m g.

  4. Solve for the critical mass: m=PgaugeAg=(4.50×105 Pa)(0.04909 m2)9.80 m/s2≈2.254×103 kgm = \frac{P_{\text{gauge}} A}{g} = \frac{(4.50 \times 10^5\text{ Pa})(0.04909\text{ m}^2)}{9.80\text{ m/s}^2} \approx 2.254 \times 10^3\text{ kg}.

Final answer

mcrit≈2.26×103 kgm_{\text{crit}} \approx 2.26 \times 10^3\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • When solving fluid-mechanics equilibrium problems, sketch a free-body diagram showing forces from all fluid boundaries rather than equating weight directly to internal pressure.

  • Practice recognizing when ambient atmospheric pressure cancels out on opposing boundaries.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to square the radius when calculating the cross-sectional area of the piston.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=0.125 mr = 0.125\text{ m}

  2. Step 2

    A=π⋅r=π(0.125)≈0.3927 m2A = \pi \cdot r = \pi (0.125) \approx 0.3927\text{ m}^2

    Correct

    A=πr2=π(0.125 m)2≈0.04909 m2A = \pi r^2 = \pi (0.125\text{ m})^2 \approx 0.04909\text{ m}^2

    You forgot to square the radius when computing the circular cross-sectional area. The area of a circle is A=πr2A = \pi r^2, not πr\pi r.

  3. Step 3

    m=P⋅Ag=(4.50×105)(0.3927)9.80≈18032 kgm = \frac{P \cdot A}{g} = \frac{(4.50 \times 10^5)(0.3927)}{9.80} \approx 18032\text{ kg}

    Correct

    mcrit=PgaugeAg=(4.50×105 Pa)(0.04909 m2)9.80 m/s2≈2.26×103 kgm_{\text{crit}} = \frac{P_{\text{gauge}} A}{g} = \frac{(4.50 \times 10^5\text{ Pa})(0.04909\text{ m}^2)}{9.80\text{ m/s}^2} \approx 2.26 \times 10^3\text{ kg}

    Your equilibrium equation m=P⋅Agm = \frac{P \cdot A}{g} is physically correct, but the resulting mass is an order of magnitude too large due to the incorrect area from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly found the radius from the diameter as r=0.125 mr = 0.125\text{ m}.

You recognized that the piston's weight balances the gauge pressure force via mg=PgaugeAm g = P_{\text{gauge}} A.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula recall error (circular area)

You omitted the exponent 22 on the radius, writing A=πrA = \pi r instead of A=πr2A = \pi r^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear dimensions with two-dimensional area formulas leads to dimensionally inconsistent expressions ([m][\text{m}] instead of [m2][\text{m}^2]).

REASONING PATH
Your ACEpath teacher’s suggested approach
Check area dimensions
  • Area must always have units of length squared (e.g., m2\text{m}^2).

  • Whenever computing the area of a circle, verify that the radius is raised to the second power: A=πr2A = \pi r^2 or A=πD24A = \frac{\pi D^2}{4}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the correct cross-sectional area: A=πr2=π(0.125 m)2≈4.9087×10−2 m2A = \pi r^2 = \pi (0.125\text{ m})^2 \approx 4.9087 \times 10^{-2}\text{ m}^2.

  2. Substitute AA into the equilibrium condition: mcrit=(4.50×105 Pa)(4.9087×10−2 m2)9.80 m/s2m_{\text{crit}} = \frac{(4.50 \times 10^5\text{ Pa})(4.9087 \times 10^{-2}\text{ m}^2)}{9.80\text{ m/s}^2}.

  3. Evaluate the final critical mass: mcrit≈2.26×103 kgm_{\text{crit}} \approx 2.26 \times 10^3\text{ kg}.

Final answer

mcrit=2.26×103 kgm_{\text{crit}} = 2.26 \times 10^3\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that area formulas always involve squaring a length dimension before performing substitutions.

  • Perform a quick dimensional analysis on intermediate calculated values to ensure the units match expected quantities.

Lock it in

Similar question

01

A hydraulic press has a circular piston of diameter D=0.100 mD = 0.100\text{ m}. What downward force must be applied to produce a gauge pressure of 2.00×105 Pa2.00 \times 10^5\text{ Pa} in the hydraulic oil?

Answer

F=PgaugeA=Pgauge(πD24)=(2.00×105)(π(0.100)24)=1.57×103 NF = P_{\text{gauge}} A = P_{\text{gauge}} \left(\frac{\pi D^2}{4}\right) = (2.00 \times 10^5)\left(\frac{\pi (0.100)^2}{4}\right) = 1.57 \times 10^3\text{ N}

02

A vertical cylinder of inner diameter D=0.400 mD = 0.400\text{ m} contains compressed gas sealed by a heavy piston. If the maximum safe gauge pressure is 1.20×105 Pa1.20 \times 10^5\text{ Pa}, determine the maximum piston mass mm that can rest on the gas in static equilibrium (g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer

A=π(0.400 m)24=0.1257 m2A = \frac{\pi (0.400\text{ m})^2}{4} = 0.1257\text{ m}^2. Balancing vertical forces gives mg=PgaugeA  ⟹  m=(1.20×105 Pa)(0.1257 m2)9.80 m/s2≈1.54×103 kgmg = P_{\text{gauge}} A \implies m = \frac{(1.20 \times 10^5\text{ Pa})(0.1257\text{ m}^2)}{9.80\text{ m/s}^2} \approx 1.54 \times 10^3\text{ kg}.

03

Two vertical hydraulic cylinders, cylinder 1 of diameter D1=0.10 mD_1 = 0.10\text{ m} and cylinder 2 of diameter D2=0.30 mD_2 = 0.30\text{ m}, support pistons of mass m1m_1 and m2m_2 respectively. If both chambers develop the same internal gauge pressure, find the ratio of their masses m2m1\frac{m_2}{m_1}.

Answer

Since Pgauge=mgAP_{\text{gauge}} = \frac{m g}{A}, equal gauge pressure implies m1A1=m2A2\frac{m_1}{A_1} = \frac{m_2}{A_2}, so m2m1=A2A1=πD22/4πD12/4=(D2D1)2=(0.300.10)2=9\frac{m_2}{m_1} = \frac{A_2}{A_1} = \frac{\pi D_2^2 / 4}{\pi D_1^2 / 4} = \left(\frac{D_2}{D_1}\right)^2 = \left(\frac{0.30}{0.10}\right)^2 = 9.

Loading workspace…