Resources

An optical lever galvanometer uses a light beam reflected from a small plane mirror attached to a suspended coil to measure minute currents. The mirror is situated at a distance of R=1.25 mR = 1.25\text{ m} from a curved translucent millimeter scale centered on the zero-deflection mark. When an unknown current II passes through the galvanometer, the mirror rotates by an angle θm\theta_m, producing a linear arc deflection of s=85.0 mms = 85.0\text{ mm} on the scale. Given that the galvanometer has a known current sensitivity of Si=1.80×103 rad/AS_i = 1.80\times 10^3\text{ rad/A} (where θm=SiI\theta_m = S_i I), determine: (a) the rotation angle of the mirror θm\theta_m in milliradians (mrad\text{mrad}), and (b) the electric current II in microamperes (μA\mu\text{A}).

Answer and steps

Final answer

(a) θm=34.0 mrad\theta_m = 34.0\text{ mrad}; (b) I=18.9 μAI = 18.9\text{ }\mu\text{A}

Steps

Part (a): Determining the Rotation Angle of the Mirror (θm\theta_m)

  1. Principle of the Optical Lever: When a plane mirror turns through an angle θm\theta_m while the incident light ray remains fixed, the angle of incidence changes by θm\theta_m. According to the law of reflection, the angle of reflection must also change by θm\theta_m. Consequently, the total angular deflection of the reflected beam, θbeam\theta_{\text{beam}}, is twice the angle of rotation of the mirror: θbeam=2θm\theta_{\text{beam}} = 2\theta_m
  2. Relating Arc Length to Beam Deflection: Because the scale is curved into a circular arc of radius R=1.25 mR = 1.25\text{ m} centered on the mirror, the linear deflection ss measured along the arc corresponds directly to the angular displacement in radians: s=R⋅θbeam=2Rθms = R \cdot \theta_{\text{beam}} = 2 R \theta_m
  3. Calculating θm\theta_m: Rearrange the formula to solve for θm\theta_m: θm=s2R\theta_m = \frac{s}{2R}

    Convert the given values to consistent units:

    • s=85.0 mm=0.0850 ms = 85.0\text{ mm} = 0.0850\text{ m}
    • R=1.25 mR = 1.25\text{ m}

    Substitute these values: θm=0.0850 m2⋅1.25 m=0.08502.50 rad=0.0340 rad\theta_m = \frac{0.0850\text{ m}}{2 \cdot 1.25\text{ m}} = \frac{0.0850}{2.50}\text{ rad} = 0.0340\text{ rad}

    Convert radians to milliradians (1 rad=103 mrad1\text{ rad} = 10^3\text{ mrad}): θm=0.0340⋅103 mrad=34.0 mrad\theta_m = 0.0340 \cdot 10^3\text{ mrad} = 34.0\text{ mrad}

Pitfall to avoid: A common error is setting s=Rθms = R \theta_m, omitting the factor of 22. Always account for the doubling of the beam's deflection upon mirror rotation.


Part (b): Determining the Electric Current (II)

  1. Relating Mirror Deflection to Current: The current sensitivity of the galvanometer is defined as: θm=SiI\theta_m = S_i I where:

    • θm=0.0340 rad\theta_m = 0.0340\text{ rad}
    • Si=1.80×103 rad/AS_i = 1.80 \times 10^3\text{ rad/A}
  2. Calculating the Current: Rearrange for II: I=θmSi=0.0340 rad1.80×103 rad/A≈1.889×10−5 AI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80 \times 10^3\text{ rad/A}} \approx 1.889 \times 10^{-5}\text{ A}
  3. Convert to Microamperes (μA\mu\text{A}): I=1.889×10−5 A⋅106 μA1 A≈18.9 μAI = 1.889 \times 10^{-5}\text{ A} \cdot \frac{10^6\text{ }\mu\text{A}}{1\text{ A}} \approx 18.9\text{ }\mu\text{A}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that reflection doubles the angular deflection of the beam and sets the beam deflection equal to the mirror rotation, doubling both the calculated angle and the current.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    s=Rθm  ⟹  θm=sR=85.0 mm1.25 m=0.0850 m1.25 m=0.0680 rad=68.0 mrads = R\theta_m \implies \theta_m = \frac{s}{R} = \frac{85.0\text{ mm}}{1.25\text{ m}} = \frac{0.0850\text{ m}}{1.25\text{ m}} = 0.0680\text{ rad} = 68.0\text{ mrad}

    Correct

    s=Rθbeam=2Rθm  ⟹  θm=s2R=0.0850 m2(1.25 m)=0.0340 rad=34.0 mrads = R\theta_{\text{beam}} = 2R\theta_m \implies \theta_m = \frac{s}{2R} = \frac{0.0850\text{ m}}{2(1.25\text{ m})} = 0.0340\text{ rad} = 34.0\text{ mrad}

    When a plane mirror rotates by an angle θm\theta_m while the incident light beam remains fixed, the reflected beam deflects by an angle θbeam=2θm\theta_{\text{beam}} = 2\theta_m due to the law of reflection. Therefore, the arc length on the scale is s=2Rθms = 2R\theta_m, not RθmR\theta_m.

  2. Step 2

    I=θmSi=0.0680 rad1.80×103 rad/A=3.78×10−5 A=37.8 μAI = \frac{\theta_m}{S_i} = \frac{0.0680\text{ rad}}{1.80\times 10^3\text{ rad/A}} = 3.78\times 10^{-5}\text{ A} = 37.8\text{ }\mu\text{A}

    Correct

    I=θmSi=0.0340 rad1.80×103 rad/A≈1.89×10−5 A=18.9 μAI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80\times 10^3\text{ rad/A}} \approx 1.89\times 10^{-5}\text{ A} = 18.9\text{ }\mu\text{A}

    Your algebraic rearrangement and unit conversion for current were executed correctly, but substituting the doubled angle θm=68.0 mrad\theta_m = 68.0\text{ mrad} carried the error through to your final current.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the arc deflection from millimeters to meters.

You correctly identified and applied the relationship between mirror deflection, current sensitivity, and current (I=θmSiI = \frac{\theta_m}{S_i}).

You converted your final current into microamperes accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing optical lever doubling factor

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the angular displacement of the reflected beam as equal to the rotation angle of the mirror itself, overlooking that reflecting a beam off a mirror rotated by an angle θ\theta shifts both the angle of incidence and the angle of reflection by θ\theta, producing a total beam deflection of 2θ2\theta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Optical lever reflection law
  • For a fixed incident ray, rotating a plane mirror by θm\theta_m rotates the normal by θm\theta_m, increasing the incidence angle by θm\theta_m and the reflection angle by θm\theta_m, so θbeam=2θm\theta_{\text{beam}} = 2\theta_m.

  • Always write s=R(2θm)s = R(2\theta_m) when finding the scale deflection produced by a rotating mirror.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the optical lever relationship θbeam=2θm\theta_{\text{beam}} = 2\theta_m to relate the linear arc deflection to the mirror rotation: s=R(2θm)s = R(2\theta_m).

  2. Solve for the mirror angle: θm=s2R=0.0850 m2(1.25 m)=0.0340 rad=34.0 mrad\theta_m = \frac{s}{2R} = \frac{0.0850\text{ m}}{2(1.25\text{ m})} = 0.0340\text{ rad} = 34.0\text{ mrad}.

  3. Calculate the current from the galvanometer sensitivity: I=θmSi=0.0340 rad1.80×103 rad/A≈1.89×10−5 A=18.9 μAI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80\times 10^3\text{ rad/A}} \approx 1.89\times 10^{-5}\text{ A} = 18.9\text{ }\mu\text{A}.

Final answer

(a) θm=34.0 mrad\theta_m = 34.0\text{ mrad}; (b) I=18.9 μAI = 18.9\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the ray geometry of reflection from a rotated plane mirror to reinforce why the deflection angle doubles.

  • When dealing with optical levers, galvanometers, or sextants, write down θbeam=2θm\theta_{\text{beam}} = 2\theta_m before writing down the arc length formula.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the optical lever relation as θ_m = 2θ instead of θ = 2θ_m, dividing by 2 an extra time and underestimating the angle and current by a factor of 4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    θ=sR=85.0 mm1.25 m=0.0680 rad\theta = \frac{s}{R} = \frac{85.0\text{ mm}}{1.25\text{ m}} = 0.0680\text{ rad}

  2. Step 2

    θm=θ2  ⟹  θm=0.06804=0.0170 rad=17.0 mrad\theta_m = \frac{\theta}{2} \implies \theta_m = \frac{0.0680}{4} = 0.0170\text{ rad} = 17.0\text{ mrad}

    Correct

    θm=θ2=0.0680 rad2=0.0340 rad=34.0 mrad\theta_m = \frac{\theta}{2} = \frac{0.0680\text{ rad}}{2} = 0.0340\text{ rad} = 34.0\text{ mrad}

    Although you correctly wrote the relationship θm=θ2\theta_m = \frac{\theta}{2}, you substituted 44 into the denominator instead of 22. Dividing by 44 halved the true mirror rotation angle.

  3. Step 3

    I=θmSi=0.0170 rad1.80×103 rad/A=9.44×10−6 A=9.44 μAI = \frac{\theta_m}{S_i} = \frac{0.0170\text{ rad}}{1.80 \times 10^3\text{ rad/A}} = 9.44 \times 10^{-6}\text{ A} = 9.44\text{ }\mu\text{A}

    Correct

    I=θmSi=0.0340 rad1.80×103 rad/A≈1.89×10−5 A=18.9 μAI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80 \times 10^3\text{ rad/A}} \approx 1.89 \times 10^{-5}\text{ A} = 18.9\text{ }\mu\text{A}

    You applied the current sensitivity relationship correctly, but your final current is halved because of the error in θm\theta_m from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the arc length relation θ=sR\theta = \frac{s}{R} to find the total angular deflection of the reflected beam.

You correctly identified the formula θm=θ2\theta_m = \frac{\theta}{2} relating the mirror rotation to the beam deflection.

You correctly rearranged and applied the galvanometer sensitivity equation I=θmSiI = \frac{\theta_m}{S_i}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Extra factor of 2 in denominator

You wrote θm=θ2\theta_m = \frac{\theta}{2} symbolically, but replaced the denominator with 44 when substituting θ=0.0680 rad\theta = 0.0680\text{ rad}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You accidentally divided by the optical lever factor of 22 twice—once when setting up the relation and again during substitution—resulting in dividing by 44 instead of 22.

REASONING PATH
Your ACEpath teacher’s suggested approach
Optical lever law
  • When a plane mirror rotates by θm\theta_m, the reflected beam deflects by θbeam=2θm\theta_{\text{beam}} = 2\theta_m. Therefore, θm=θbeam2\theta_m = \frac{\theta_{\text{beam}}}{2}.

  • Calculate θbeam=sR\theta_{\text{beam}} = \frac{s}{R} first, then divide by 22 exactly once to get θm\theta_m.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. θm=θ2=0.0680 rad2=0.0340 rad=34.0 mrad\theta_m = \frac{\theta}{2} = \frac{0.0680\text{ rad}}{2} = 0.0340\text{ rad} = 34.0\text{ mrad}

  2. I=θmSi=0.0340 rad1.80×103 rad/A≈1.889×10−5 A=18.9 μAI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80 \times 10^3\text{ rad/A}} \approx 1.889 \times 10^{-5}\text{ A} = 18.9\text{ }\mu\text{A}

Final answer

(a) θm=34.0 mrad\theta_m = 34.0\text{ mrad}; (b) I=18.9 μAI = 18.9\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that symbolic denominators match numerical denominators directly during substitution so extra factors are not introduced.

  • Remember that the beam turns through twice the mirror's angle (θbeam=2θm\theta_{\text{beam}} = 2\theta_m), meaning the mirror angle is always half the beam angle, not a quarter.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly multiplies by current sensitivity instead of dividing when solving for current from θ_m = S_i I.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    θ=2θm  ⟹  θ=sR=0.0850 m1.25 m=0.0680 rad  ⟹  θm=0.0680 rad2=0.0340 rad=34.0 mrad\theta = 2\theta_m \implies \theta = \frac{s}{R} = \frac{0.0850\text{ m}}{1.25\text{ m}} = 0.0680\text{ rad} \implies \theta_m = \frac{0.0680\text{ rad}}{2} = 0.0340\text{ rad} = 34.0\text{ mrad}

  2. Step 2

    I=θm×Si  ⟹  I=0.0340 rad×(1.80×103 rad/A)  ⟹  I=61.2 AI = \theta_m \times S_i \implies I = 0.0340\text{ rad} \times (1.80 \times 10^3\text{ rad/A}) \implies I = 61.2\text{ A}

    Correct

    I=θmSi=0.0340 rad1.80×103 rad/A≈1.889×10−5 A=18.9 μAI = \frac{\theta_m}{S_i} = \frac{0.0340\text{ rad}}{1.80 \times 10^3\text{ rad/A}} \approx 1.889 \times 10^{-5}\text{ A} = 18.9\text{ }\mu\text{A}

    You multiplied the deflection angle by SiS_i instead of dividing. Since current sensitivity is defined by θm=SiI\theta_m = S_i I, isolating current requires I=θmSiI = \frac{\theta_m}{S_i}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the optical lever principle where the reflected beam deflects by twice the mirror's rotation angle.

You converted units properly to find the arc angle and stated the mirror angle in milliradians.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted algebraic rearrangement of sensitivity formula

You algebraically solved for current by multiplying by sensitivity rather than dividing.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misinterpreting the sensitivity definition θm=SiI\theta_m = S_i I and failing to verify the units of the resulting quantity, which yielded rad2/A\text{rad}^2/\text{A} instead of A\text{A}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Algebraic Isolation
  • For a linear relation y=kxy = k x, isolating the independent variable requires x=ykx = \frac{y}{k}.

  • Rearrange the symbolic equation θm=SiI\theta_m = S_i I completely before substituting numerical values.

Dimensional Unit Check
  • The units of the quotient radrad/A\frac{\text{rad}}{\text{rad/A}} simplify to A\text{A}, whereas rad×(rad/A)=rad2/A\text{rad} \times (\text{rad/A}) = \text{rad}^2/\text{A}.

  • Always carry units through your calculation to verify that your algebraic operation produces the intended unit.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the governing relation: θm=SiI\theta_m = S_i I.

  2. Isolate current II: I=θmSiI = \frac{\theta_m}{S_i}.

  3. Substitute known values: I=0.0340 rad1.80×103 rad/A≈1.889×10−5 AI = \frac{0.0340\text{ rad}}{1.80 \times 10^3\text{ rad/A}} \approx 1.889 \times 10^{-5}\text{ A}.

  4. Convert to microamperes: 1.889×10−5 A×106 μA/A=18.9 μA1.889 \times 10^{-5}\text{ A} \times 10^6\text{ }\mu\text{A/A} = 18.9\text{ }\mu\text{A}.

Final answer

I=18.9 μAI = 18.9\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables from definitions of sensitivity, capacitance, or resistance before plugging in numbers.

  • Perform dimensional analysis on intermediate and final steps to catch inadvertent multiplication/division swaps.

Lock it in

Similar question

01

A laser beam shines onto a small flat mirror placed at the center of a circular wall of radius 2.00 m2.00\text{ m}. If the mirror rotates by 1.50∘1.50^\circ, find the arc length traveled by the reflected spot along the wall.

Answer

s=R(2θm)=(2.00 m)⋅(2⋅1.50∘⋅π180∘)=(2.00 m)(0.05236 rad)≈0.105 m=10.5 cms = R(2\theta_m) = (2.00\text{ m}) \cdot \left(2 \cdot 1.50^\circ \cdot \frac{\pi}{180^\circ}\right) = (2.00\text{ m})(0.05236\text{ rad}) \approx 0.105\text{ m} = 10.5\text{ cm}.

02

An optical lever galvanometer has a curved scale placed at a distance of R=1.50 mR = 1.50\text{ m}. A current of I=25.0 μAI = 25.0\text{ }\mu\text{A} causes a spot deflection of s=60.0 mms = 60.0\text{ mm} along the arc. Calculate the current sensitivity Si=θmIS_i = \frac{\theta_m}{I} of the galvanometer in rad/A\text{rad/A}.

Answer

First, the mirror angle is θm=s2R=0.0600 m2(1.50 m)=0.0200 rad=20.0 mrad\theta_m = \frac{s}{2R} = \frac{0.0600\text{ m}}{2(1.50\text{ m})} = 0.0200\text{ rad} = 20.0\text{ mrad}. Then, Si=θmI=0.0200 rad2.50×10−5 A=800 rad/AS_i = \frac{\theta_m}{I} = \frac{0.0200\text{ rad}}{2.50 \times 10^{-5}\text{ A}} = 800\text{ rad/A}.

03

A light beam reflects from a galvanometer mirror onto a flat vertical scale located a perpendicular distance L=1.00 mL = 1.00\text{ m} away. For small deflections, the linear shift on the flat scale is y≈Ltan⁡(θbeam)≈Lθbeamy \approx L \tan(\theta_{\text{beam}}) \approx L \theta_{\text{beam}}. If a current produces a shift of y=48.0 mmy = 48.0\text{ mm} and the galvanometer's sensitivity is Si=1.60×103 rad/AS_i = 1.60\times 10^3\text{ rad/A}, find the current II in microamperes.

Answer

The beam angle is θbeam≈yL=0.0480 m1.00 m=0.0480 rad\theta_{\text{beam}} \approx \frac{y}{L} = \frac{0.0480\text{ m}}{1.00\text{ m}} = 0.0480\text{ rad}. The mirror rotation is θm=θbeam2=0.0240 rad\theta_m = \frac{\theta_{\text{beam}}}{2} = 0.0240\text{ rad}. Thus, I=θmSi=0.0240 rad1.60×103 rad/A=1.50×10−5 A=15.0 μAI = \frac{\theta_m}{S_i} = \frac{0.0240\text{ rad}}{1.60 \times 10^3\text{ rad/A}} = 1.50 \times 10^{-5}\text{ A} = 15.0\text{ }\mu\text{A}.

Loading workspace…