Resources

A 10.0 μF10.0\text{ }\mu\text{F} capacitor is connected in a single-loop series circuit with an open switch, a 20.0 V20.0\text{ V} DC supply, and a 50.0 kΩ50.0\text{ }\text{k}\Omega resistor. At t=0 st = 0\text{ s}, the switch is closed to charge the capacitor until t1=0.400 st_1 = 0.400\text{ s}. At instant t1t_1, the switch is instantaneously thrown to a second position that completely disconnects the DC power supply and connects the partially charged capacitor across a different discharge resistor R2=120 kΩR_2 = 120\text{ }\text{k}\Omega. Find: (a) the electric potential across the capacitor at t1=0.400 st_1 = 0.400\text{ s}, and (b) the instantaneous current through R2R_2 at t=1.000 st = 1.000\text{ s} (which is 0.600 s0.600\text{ s} after the switch was thrown).

Answer and steps

Final answer

(a) vC(0.400 s)=11.0 Vv_C(0.400\text{ s}) = 11.0\text{ V}; (b) i2=55.7 μAi_2 = 55.7\text{ }\mu\text{A}

Steps

Part (a): Potential Across the Capacitor at t1=0.400 st_1 = 0.400\text{ s}

  1. Determine the time constant of the charging circuit (τ1\tau_1): An uncharged capacitor charged through a resistor R1R_1 by a constant DC voltage VsV_s responds according to the characteristic charging time constant: τ1=R1C\tau_1 = R_1 C Substituting the given values: τ1=(50.0×103 Ω)(10.0×10−6 F)=0.500 s\tau_1 = (50.0 \times 10^3\text{ }\Omega)(10.0 \times 10^{-6}\text{ F}) = 0.500\text{ s}
  2. Calculate the capacitor voltage at t1=0.400 st_1 = 0.400\text{ s}: The equation for the voltage across an initially uncharged capacitor during charging is: vC(t)=Vs(1−e−t/τ1)v_C(t) = V_s \left(1 - e^{-t / \tau_1}\right) Evaluating at t1=0.400 st_1 = 0.400\text{ s}: vC(0.400 s)=20.0(1−e−0.400/0.500)=20.0(1−e−0.800)v_C(0.400\text{ s}) = 20.0 \left(1 - e^{-0.400 / 0.500}\right) = 20.0 \left(1 - e^{-0.800}\right) Since e−0.800≈0.4493e^{-0.800} \approx 0.4493: vC(0.400 s)=20.0⋅(1−0.4493)=20.0⋅0.5507≈11.0 Vv_C(0.400\text{ s}) = 20.0 \cdot (1 - 0.4493) = 20.0 \cdot 0.5507 \approx 11.0\text{ V}

Part (b): Instantaneous Current Through R2R_2 at t=1.000 st = 1.000\text{ s}

  1. Identify the initial conditions and time constant for the discharge phase: At t1=0.400 st_1 = 0.400\text{ s}, the capacitor acts as a temporary voltage source with an initial potential: V0=vC(0.400 s)≈11.013 VV_0 = v_C(0.400\text{ s}) \approx 11.013\text{ V} The new discharge loop contains only capacitor CC and resistor R2=120 kΩR_2 = 120\text{ k}\Omega. The time constant for discharging is: τ2=R2C=(120×103 Ω)(10.0×10−6 F)=1.20 s\tau_2 = R_2 C = (120 \times 10^3\text{ }\Omega)(10.0 \times 10^{-6}\text{ F}) = 1.20\text{ s}
  2. Determine the elapsed time in the discharge phase (Δt\Delta t): The switch was thrown at t1=0.400 st_1 = 0.400\text{ s}, so at t=1.000 st = 1.000\text{ s}, the time spent discharging is: Δt=1.000 s−0.400 s=0.600 s\Delta t = 1.000\text{ s} - 0.400\text{ s} = 0.600\text{ s} (Pitfall: Do not plug t=1.000 st = 1.000\text{ s} directly into the discharge decay formula; the exponential decay only began at t=0.400 st = 0.400\text{ s}.)
  3. Calculate the discharge current i2i_2: The instantaneous current through resistor R2R_2 during capacitor discharge follows: i2(Δt)=V0R2e−Δt/τ2i_2(\Delta t) = \frac{V_0}{R_2} e^{-\Delta t / \tau_2} The peak discharge current at the start of discharge (Δt=0\Delta t = 0) is: I0=V0R2=11.013 V120×103 Ω≈9.178×10−5 AI_0 = \frac{V_0}{R_2} = \frac{11.013\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 9.178 \times 10^{-5}\text{ A} Evaluating at Δt=0.600 s\Delta t = 0.600\text{ s}: i2(0.600 s)=(9.178×10−5 A)⋅e−0.600/1.20=(9.178×10−5 A)⋅e−0.500i_2(0.600\text{ s}) = (9.178 \times 10^{-5}\text{ A}) \cdot e^{-0.600 / 1.20} = (9.178 \times 10^{-5}\text{ A}) \cdot e^{-0.500} Since e−0.500≈0.6065e^{-0.500} \approx 0.6065: i2=(9.178×10−5 A)⋅0.6065≈5.57×10−5 A=55.7 μAi_2 = (9.178 \times 10^{-5}\text{ A}) \cdot 0.6065 \approx 5.57 \times 10^{-5}\text{ A} = 55.7\text{ }\mu\text{A}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the charging formula with the discharging decay formula by using V_C(t) = V_0 · e^(-t / τ) during the charging phase.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ1=R1⋅C=50.0×103⋅10.0×10−6=0.500 s\tau_1 = R_1 \cdot C = 50.0 \times 10^3 \cdot 10.0 \times 10^{-6} = 0.500\text{ s}

  2. Step 2

    VC(t1)=V0⋅e−t1/τ1  ⟹  VC(0.400 s)=20.0⋅e−0.4000.500=20.0⋅e−0.800≈8.99 VV_C(t_1) = V_0 \cdot e^{-t_1 / \tau_1} \implies V_C(0.400\text{ s}) = 20.0 \cdot e^{-\frac{0.400}{0.500}} = 20.0 \cdot e^{-0.800} \approx 8.99\text{ V}

    Correct

    vC(t1)=Vs(1−e−t1/τ1)=20.0(1−e−0.800)≈11.0 Vv_C(t_1) = V_s \left(1 - e^{-t_1 / \tau_1}\right) = 20.0\left(1 - e^{-0.800}\right) \approx 11.0\text{ V}

    You applied the decay equation V0e−t/τV_0 e^{-t/\tau} instead of the charging equation Vs(1−e−t/τ)V_s(1 - e^{-t/\tau}). Starting from zero charge, the voltage rises toward VsV_s rather than decaying from it.

  3. Step 3

    τ2=R2⋅C=120×103⋅10.0×10−6=1.20 s  ⟹  Δt=1.000−0.400=0.600 s\tau_2 = R_2 \cdot C = 120 \times 10^3 \cdot 10.0 \times 10^{-6} = 1.20\text{ s} \implies \Delta t = 1.000 - 0.400 = 0.600\text{ s}

  4. Step 4

    VC(1.000 s)=8.99⋅e−0.6001.20≈5.45 V  ⟹  I(1.000 s)=5.45120×103≈4.54×10−5 AV_C(1.000\text{ s}) = 8.99 \cdot e^{-\frac{0.600}{1.20}} \approx 5.45\text{ V} \implies I(1.000\text{ s}) = \frac{5.45}{120 \times 10^3} \approx 4.54 \times 10^{-5}\text{ A}

    Correct

    i2=vC(0.400 s)R2e−Δt/τ2=11.013 V120×103 Ωe−0.500≈55.7 μAi_2 = \frac{v_C(0.400\text{ s})}{R_2} e^{-\Delta t / \tau_2} = \frac{11.013\text{ V}}{120 \times 10^3\text{ }\Omega} e^{-0.500} \approx 55.7\text{ }\mu\text{A}

    Your method for calculating the discharge voltage and Ohm's law current is completely sound, but your numerical answer is affected by the incorrect initial voltage from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed both time constants τ1\tau_1 and τ2\tau_2.

You correctly recognized that the discharge phase only lasts for Δt=0.600 s\Delta t = 0.600\text{ s} rather than using the total time t=1.000 st = 1.000\text{ s}.

You applied Ohm's law accurately to find the discharge current from the capacitor voltage.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confused charging and discharging voltage formulas

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the voltage build-up formula vC(t)=Vs(1−e−t/τ)v_C(t) = V_s(1 - e^{-t/\tau}) for an initially uncharged capacitor with the natural exponential decay formula vC(t)=V0e−t/τv_C(t) = V_0 e^{-t/\tau} used for discharging.

REASONING PATH
Your ACEpath teacher’s suggested approach
Charging vs. Discharging Boundary Conditions
  • An uncharged capacitor starts at vC(0)=0 Vv_C(0) = 0\text{ V} and approaches VsV_s as t→∞t \to \infty, requiring the factor (1−e−t/τ)(1 - e^{-t/\tau}). Pure decay e−t/τe^{-t/\tau} drops from V0V_0 toward 0 V0\text{ V}.

  • Always check the boundary value at t=0t = 0: if the capacitor begins uncharged, verify that vC(0)=0 Vv_C(0) = 0\text{ V} before carrying out calculations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the charging equation for an uncharged capacitor: vC(t1)=Vs(1−e−t1/τ1)v_C(t_1) = V_s \left(1 - e^{-t_1 / \tau_1}\right)

  2. Substitute Vs=20.0 VV_s = 20.0\text{ V}, t1=0.400 st_1 = 0.400\text{ s}, and τ1=0.500 s\tau_1 = 0.500\text{ s}: vC(0.400 s)=20.0(1−e−0.800)≈11.013 Vv_C(0.400\text{ s}) = 20.0\left(1 - e^{-0.800}\right) \approx 11.013\text{ V}

  3. Determine the initial discharge current at Δt=0\Delta t = 0: I0=V0R2=11.013 V120×103 Ω≈9.178×10−5 AI_0 = \frac{V_0}{R_2} = \frac{11.013\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 9.178 \times 10^{-5}\text{ A}

  4. Evaluate the decaying current at Δt=0.600 s\Delta t = 0.600\text{ s}: i2=I0e−Δt/τ2=(9.178×10−5 A)e−0.600/1.20≈55.7 μAi_2 = I_0 e^{-\Delta t / \tau_2} = (9.178 \times 10^{-5}\text{ A}) e^{-0.600 / 1.20} \approx 55.7\text{ }\mu\text{A}

Final answer

(a) vC(0.400 s)=11.0 Vv_C(0.400\text{ s}) = 11.0\text{ V}; (b) i2=55.7 μAi_2 = 55.7\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the initial and final conditions for series RC circuits to distinguish (1−e−t/τ)(1 - e^{-t/\tau}) from e−t/τe^{-t/\tau}.

  • Practice testing t=0t = 0 and t→∞t \to \infty as a quick sanity check on any transient formula you write down.

OverviewACEpath Teacher's Diagnosis

02 The student uses the total time t = 1.000 s in the discharge formula rather than the elapsed discharge time Δt = 0.600 s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ1=R1⋅C=50.0×103⋅10.0×10−6=0.500 s\tau_1 = R_1 \cdot C = 50.0 \times 10^3 \cdot 10.0 \times 10^{-6} = 0.500\text{ s}

  2. Step 2

    VC(0.400 s)=20.0⋅(1−e−0.400/0.500)=20.0⋅(1−e−0.800)≈11.0 VV_C(0.400\text{ s}) = 20.0 \cdot (1 - e^{-0.400/0.500}) = 20.0 \cdot (1 - e^{-0.800}) \approx 11.0\text{ V}

  3. Step 3

    τ2=R2⋅C=120×103⋅10.0×10−6=1.20 s\tau_2 = R_2 \cdot C = 120 \times 10^3 \cdot 10.0 \times 10^{-6} = 1.20\text{ s}

  4. Step 4

    VC(1.000 s)=11.0⋅e−1.000/1.20≈11.0⋅e−0.833≈4.78 VV_C(1.000\text{ s}) = 11.0 \cdot e^{-1.000/1.20} \approx 11.0 \cdot e^{-0.833} \approx 4.78\text{ V}

    Correct

    vC(1.000 s)=V0e−Δt/τ2=11.013⋅e−(1.000−0.400)/1.20=11.013⋅e−0.500≈6.68 Vv_C(1.000\text{ s}) = V_0 e^{-\Delta t / \tau_2} = 11.013 \cdot e^{-(1.000 - 0.400)/1.20} = 11.013 \cdot e^{-0.500} \approx 6.68\text{ V}

    You used the total clock time t=1.000 st = 1.000\text{ s} as the decay duration, but discharging only started at t1=0.400 st_1 = 0.400\text{ s}. The elapsed decay time is Δt=1.000 s−0.400 s=0.600 s\Delta t = 1.000\text{ s} - 0.400\text{ s} = 0.600\text{ s}.

  5. Step 5

    I(1.000 s)=4.78/(120×103)≈3.98×10−5 AI(1.000\text{ s}) = 4.78 / (120 \times 10^3) \approx 3.98 \times 10^{-5}\text{ A}

    Correct

    i2(1.000 s)=vC(1.000 s)R2=6.68 V120×103 Ω≈55.7 μAi_2(1.000\text{ s}) = \frac{v_C(1.000\text{ s})}{R_2} = \frac{6.68\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 55.7\text{ }\mu\text{A}

    You correctly used Ohm's law to relate the resistor current to the capacitor voltage, but this step inherited the erroneous voltage from Step 4.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated both circuit time constants τ1\tau_1 and τ2\tau_2 without any computational or unit errors.

You applied the capacitor charging equation correctly to find vC(0.400 s)≈11.0 Vv_C(0.400\text{ s}) \approx 11.0\text{ V}.

You recognized that the current through R2R_2 during discharge can be found by dividing the instantaneous capacitor voltage by R2R_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Elapsed Time vs. Clock Time in Multi-Stage Transients

You substituted the absolute experiment time t=1.000 st = 1.000\text{ s} directly into the discharge decay factor e−t/τe^{-t/\tau} instead of the time interval Δt=t−tswitch\Delta t = t - t_{\text{switch}} that the capacitor actually spent discharging.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the global reference clock tt with the local stage elapsed time Δt=t−t0\Delta t = t - t_0 when switching between sequential circuit phases.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define Phase-Specific Time
  • For any transient phase initiated at switch time tswitcht_{\text{switch}}, the exponential response is governed by Δt=t−tswitch\Delta t = t - t_{\text{switch}}, yielding e−(t−tswitch)/τe^{-(t - t_{\text{switch}})/\tau}.

  • Always write down Δt=t−tswitch\Delta t = t - t_{\text{switch}} explicitly before plugging numbers into the exponential decay formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the elapsed discharge time: Δt=1.000 s−0.400 s=0.600 s\Delta t = 1.000\text{ s} - 0.400\text{ s} = 0.600\text{ s}.

  2. Calculate the capacitor voltage at t=1.000 st = 1.000\text{ s}: vC=11.013⋅e−0.600/1.20=11.013⋅e−0.500≈6.68 Vv_C = 11.013 \cdot e^{-0.600 / 1.20} = 11.013 \cdot e^{-0.500} \approx 6.68\text{ V}.

  3. Compute the instantaneous discharge current: i2=vCR2=6.68 V120×103 Ω≈55.7 μAi_2 = \frac{v_C}{R_2} = \frac{6.68\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 55.7\text{ }\mu\text{A}.

Final answer

(a) vC(0.400 s)=11.0 Vv_C(0.400\text{ s}) = 11.0\text{ V}; (b) i2=55.7 μAi_2 = 55.7\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between global experiment clock time tt and local elapsed time Δt\Delta t in multi-phase RC circuits.

  • Practice setting up shifted exponential formulas of the form e−(t−t0)/τe^{-(t - t_0)/\tau} whenever a switch state changes at t0>0t_0 > 0.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly uses the initial charging resistor R₁ instead of the discharge resistor R₂ to calculate the discharge time constant.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ1=R1⋅C=50.0×103⋅10.0×10−6=0.500 s\tau_1 = R_1 \cdot C = 50.0 \times 10^3 \cdot 10.0 \times 10^{-6} = 0.500\text{ s}

  2. Step 2

    Vc(0.400 s)=20.0⋅(1−e−0.4000.500)=20.0⋅(1−0.4493)≈11.0 VV_c(0.400\text{ s}) = 20.0 \cdot (1 - e^{-\frac{0.400}{0.500}}) = 20.0 \cdot (1 - 0.4493) \approx 11.0\text{ V}

  3. Step 3

    τ2=R1⋅C=50.0×103⋅10.0×10−6=0.500 s\tau_2 = R_1 \cdot C = 50.0 \times 10^3 \cdot 10.0 \times 10^{-6} = 0.500\text{ s}

    Correct

    τ2=R2C=(120×103 Ω)(10.0×10−6 F)=1.20 s\tau_2 = R_2 C = (120 \times 10^3\text{ }\Omega)(10.0 \times 10^{-6}\text{ F}) = 1.20\text{ s}

    When the switch is thrown, the circuit disconnects from R1R_1 and connects across R2=120 kΩR_2 = 120\text{ k}\Omega. You should use R2R_2 rather than R1R_1 to determine the discharge time constant τ2\tau_2.

  4. Step 4

    Δt=1.000−0.400=0.600 s\Delta t = 1.000 - 0.400 = 0.600\text{ s}

  5. Step 5

    Vc(1.000 s)=11.0⋅e−0.6000.500=11.0⋅e−1.20≈3.31 VV_c(1.000\text{ s}) = 11.0 \cdot e^{-\frac{0.600}{0.500}} = 11.0 \cdot e^{-1.20} \approx 3.31\text{ V}

    Correct

    vC(Δt)=V0e−Δt/τ2=11.013⋅e−0.600/1.20=11.013⋅e−0.500≈6.68 Vv_C(\Delta t) = V_0 e^{-\Delta t / \tau_2} = 11.013 \cdot e^{-0.600 / 1.20} = 11.013 \cdot e^{-0.500} \approx 6.68\text{ V}

    Your exponential decay setup is conceptually sound, but the result is affected by substituting your incorrect time constant τ2=0.500 s\tau_2 = 0.500\text{ s} instead of 1.20 s1.20\text{ s}.

  6. Step 6

    I(1.000 s)=3.31120×103≈2.76×10−5 AI(1.000\text{ s}) = \frac{3.31}{120 \times 10^3} \approx 2.76 \times 10^{-5}\text{ A}

    Correct

    i2=vC(0.600 s)R2=6.68 V120×103 Ω≈55.7 μAi_2 = \frac{v_C(0.600\text{ s})}{R_2} = \frac{6.68\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 55.7\text{ }\mu\text{A}

    You correctly applied Ohm's law across R2R_2, but your numerical answer reflects the propagated error from the voltage decay calculation.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the charging time constant τ1=0.500 s\tau_1 = 0.500\text{ s}.

You accurately found the capacitor voltage vC(0.400 s)≈11.0 Vv_C(0.400\text{ s}) \approx 11.0\text{ V} at the end of the charging phase.

You properly identified the elapsed discharge time as Δt=0.600 s\Delta t = 0.600\text{ s} rather than using the absolute time t=1.000 st = 1.000\text{ s}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Wrong resistor selected for discharge time constant

You accidentally reused R1R_1 when calculating τ2\tau_2, even though you later correctly used R2R_2 when applying Ohm's law to find the discharge current.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In multi-phase RC switching circuits, each operational phase has its own equivalent circuit loop. Failing to re-evaluate the loop resistance after a switch position change leads to reusing the previous phase's time constant.

REASONING PATH
Your ACEpath teacher’s suggested approach
Redraw or re-identify the active loop
  • Every time a switch changes position, identify the exact loop that contains the capacitor during that specific interval: τphase=RactiveC\tau_{\text{phase}} = R_{\text{active}} C.

  • Label the resistors explicitly with their active phase (RchargeR_{\text{charge}} vs. RdischargeR_{\text{discharge}}) before writing down the time constant formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the correct discharge time constant: τ2=R2C=(120×103 Ω)(10.0×10−6 F)=1.20 s\tau_2 = R_2 C = (120 \times 10^3\text{ }\Omega)(10.0 \times 10^{-6}\text{ F}) = 1.20\text{ s}.

  2. Evaluate the capacitor voltage at Δt=0.600 s\Delta t = 0.600\text{ s}: vC=11.013⋅e−0.600/1.20=11.013⋅e−0.500≈6.680 Vv_C = 11.013 \cdot e^{-0.600 / 1.20} = 11.013 \cdot e^{-0.500} \approx 6.680\text{ V}.

  3. Compute the instantaneous discharge current: i2=vCR2=6.680 V120×103 Ω≈5.57×10−5 A=55.7 μAi_2 = \frac{v_C}{R_2} = \frac{6.680\text{ V}}{120 \times 10^3\text{ }\Omega} \approx 5.57 \times 10^{-5}\text{ A} = 55.7\text{ }\mu\text{A}.

Final answer

(a) vC(0.400 s)=11.0 Vv_C(0.400\text{ s}) = 11.0\text{ V}; (b) i2=55.7 μAi_2 = 55.7\text{ }\mu\text{A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three targeted flashcards on phase-dependent RC time constants.

  • Solve the three transfer practice exercises to master multi-resistor switching problems.

Lock it in

Similar question

01

An uncharged 20.0 μF20.0\text{ }\mu\text{F} capacitor is connected in series with a 10.0 kΩ10.0\text{ k}\Omega resistor and a 15.0 V15.0\text{ V} DC power supply. What is the potential difference across the capacitor at t=0.200 st = 0.200\text{ s} after the circuit is closed?

Answer

vC(0.200 s)≈9.48 Vv_C(0.200\text{ s}) \approx 9.48\text{ V}. First find τ=RC=(10.0×103 Ω)(20.0×10−6 F)=0.200 s\tau = RC = (10.0 \times 10^3\text{ }\Omega)(20.0 \times 10^{-6}\text{ F}) = 0.200\text{ s}. Then use vC(t)=Vs(1−e−t/τ)=15.0(1−e−1)=15.0(1−0.3679)≈9.48 Vv_C(t) = V_s(1 - e^{-t/\tau}) = 15.0(1 - e^{-1}) = 15.0(1 - 0.3679) \approx 9.48\text{ V}.

02

A 5.0 μF5.0\text{ }\mu\text{F} capacitor is charged to 12.0 V12.0\text{ V} and then disconnected from the source. At t=0t = 0, it is connected across a 40.0 kΩ40.0\text{ k}\Omega resistor to discharge. Find the current flowing through the resistor at t=0.300 st = 0.300\text{ s}.

Answer

i(0.300 s)≈6.70 μAi(0.300\text{ s}) \approx 6.70\text{ }\mu\text{A}. Compute τ=RC=(40.0×103 Ω)(5.0×10−6 F)=0.200 s\tau = RC = (40.0 \times 10^3\text{ }\Omega)(5.0 \times 10^{-6}\text{ F}) = 0.200\text{ s}. The initial discharge current is I0=V0R=12.0 V40.0×103 Ω=300 μAI_0 = \frac{V_0}{R} = \frac{12.0\text{ V}}{40.0 \times 10^3\text{ }\Omega} = 300\text{ }\mu\text{A}. Then i(t)=I0e−t/τ=300 μA⋅e−0.300/0.200=300⋅e−1.5≈66.9 μAi(t) = I_0 e^{-t/\tau} = 300\text{ }\mu\text{A} \cdot e^{-0.300 / 0.200} = 300 \cdot e^{-1.5} \approx 66.9\text{ }\mu\text{A} (or 6.70×10−5 A6.70 \times 10^{-5}\text{ A}).

03

An uncharged 4.0 μF4.0\text{ }\mu\text{F} capacitor is charged through a 25 kΩ25\text{ k}\Omega resistor by a 24 V24\text{ V} source for 0.10 s0.10\text{ s}. At that exact instant, it is switched to discharge through an 80 kΩ80\text{ k}\Omega resistor. Find the voltage across the capacitor 0.16 s0.16\text{ s} after the switch is thrown.

Answer

vC≈9.17 Vv_C \approx 9.17\text{ V}. Step 1 (Charging): τ1=R1C=0.10 s\tau_1 = R_1 C = 0.10\text{ s}. At t1=0.10 st_1 = 0.10\text{ s}, V0=24(1−e−1)≈15.17 VV_0 = 24(1 - e^{-1}) \approx 15.17\text{ V}. Step 2 (Discharging): τ2=R2C=(80×103)(4.0×10−6)=0.32 s\tau_2 = R_2 C = (80 \times 10^3)(4.0 \times 10^{-6}) = 0.32\text{ s}. At Δt=0.16 s\Delta t = 0.16\text{ s}, vC=V0e−Δt/τ2=15.17⋅e−0.16/0.32=15.17⋅e−0.5≈9.17 Vv_C = V_0 e^{-\Delta t / \tau_2} = 15.17 \cdot e^{-0.16 / 0.32} = 15.17 \cdot e^{-0.5} \approx 9.17\text{ V}.

Loading workspace…