Resources
A warehouse worker pushes a crate across a level concrete floor at a constant speed by applying a steady force of magnitude directed at an angle below the horizontal. The crate is displaced horizontally by . Calculate: (a) the work done on the crate by the worker's applied force, (b) the work done by friction, and (c) the coefficient of kinetic friction between the crate and the floor. Take .
Answer and steps
Final answer
(a) ; (b) ; (c)
Steps
Part (a): Work Done by the Applied Force
The work done by a constant force acting over a displacement is given by:
where:
- is the magnitude of the pushing force,
- is the horizontal displacement,
- is the angle between the pushing force and the horizontal displacement vector.
Substitute the given values:
Part (b): Work Done by Friction
Because the crate moves at a constant speed, its kinetic energy does not change ().
According to the work-energy theorem, the net work done on the crate must be zero:
The forces acting on the crate are the applied force , kinetic friction , the normal force , and gravity . Since the normal force and gravity are perpendicular to the horizontal displacement, they do zero work ( and ).
Therefore:
(Pitfall to avoid: Work done by friction opposes the displacement, meaning its value must be negative.)
Part (c): Coefficient of Kinetic Friction
To find , determine the normal force and the friction force .
-
Analyze forces in the vertical direction (-axis):
The applied force pushes downward at an angle , adding to the vertical load on the floor. With no vertical acceleration ():Substitute the numerical values:
-
Analyze forces in the horizontal direction (-axis):
Since the crate moves at a constant velocity, the horizontal forces are balanced (): -
Calculate the coefficient of kinetic friction :
Using the kinetic friction relation :
Typical errors
01 The student ignores the vertical component of the pushing force and assumes the normal force simply equals m*g, leading to an underestimated normal force and an overestimated coefficient of friction.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You assumed , but the pushing force acts at below the horizontal, adding a downward vertical component that increases the normal force.
- Step 5Correct
Your formula is correct, but your final numerical value is off because it used the underestimated normal force from step 4.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used to calculate the work done by the applied force.
You recognized that constant speed implies zero net work, yielding the correct work done by friction.
You correctly set the friction force equal to the horizontal component of the applied force.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou defaulted to setting without drawing or checking the vertical force balance , missing the downward push component .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check all forces along the normal axis
On a horizontal floor, the normal force equals only when no other vertical forces act on the body.
Always write out before solving for .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply vertical equilibrium:
Solve for normal force:
Compute friction coefficient:
(a) , (b) , (c)
02 The student subtracts rather than adds the vertical component of the applied force when solving for the normal force, confusing pushing downward with pulling upward.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because the worker is pushing downward at an angle below the horizontal, the applied force pushes the crate further into the floor. In vertical equilibrium, , so .
- Step 4
- Step 5Correct
Your formula is correct, but your numerical answer was affected by the underestimated normal force from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the work done by the applied force using .
You applied the work-energy theorem to deduce the work done by friction at constant speed.
You correctly resolved the horizontal component of the pushing force to find the friction force.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou subtracted the vertical component of the applied force instead of adding it when setting up the vertical force balance.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated an applied pushing force directed below the horizontal as if it were a pulling force lifting the object upward, causing you to subtract from rather than adding it.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Vertical Direction of the Applied Force
A force pushed at an angle below the horizontal has a downward vertical component ().
Always draw a free-body diagram showing the direction of every component before writing Newton's second law.
- Solve for the Normal Force from Equilibrium
When an object rests on a level floor without vertical acceleration, .
Set for a downward push, and for an upward pull.
CORRECTED PATH
ACEpath Teacher's DemonstrationSum vertical forces:
Solve for :
Compute :
03 The student omits the negative sign on the work done by friction, treating work as a strictly positive scalar magnitude rather than accounting for the opposing direction.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
While your calculation of the friction force magnitude is correct, kinetic friction acts opposite to the direction of motion (an angle of relative to displacement). Because , the work done by friction must be negative.
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the applied pushing force into horizontal and vertical components.
You calculated the work done by the applied force accurately.
You correctly included the downward vertical force component when finding the normal force and determined precisely.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou computed the product of friction magnitude and displacement without incorporating the relative angle between friction and displacement.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating work as a strictly positive product of force magnitude and distance rather than the dot product , which assigns a negative sign to forces opposing motion.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dot Product Sign Rule
For any force and displacement , , where is the angle between the two vectors.
Whenever a force opposes the direction of displacement, set so that yields negative work.
- Work-Energy Consistency Check
At constant velocity, , so .
Check that the work done by resistive forces cancels positive work when speed remains constant.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the angle between the friction vector (pointing left) and the displacement vector (pointing right): .
Apply the work equation: .
(a) ; (b) ; (c)
Lock it in
When a pushing force is directed at an angle below the horizontal on a level surface, what is the normal force in equilibrium?
. Pushing downward adds to the crate's weight against the floor.
Similar question
A sled of mass is pulled along a flat horizontal surface at a constant speed by a rope exerting a force of at an angle of above the horizontal. Find the normal force acting on the sled and the coefficient of kinetic friction . Take .
Answer
, . Key steps: (1) . (2) . (3) .
A worker pushes a lawnmower with a handle tilted at below the horizontal. If the coefficient of kinetic friction between the lawnmower and the ground is , calculate the pushing force required to move the lawnmower at a constant velocity. Take .
Answer
. Key steps: (1) . (2) . (3) For constant speed, . (4) .
A block is placed on a rough horizontal surface with . A person tries to push it forward by exerting a force at an angle below the horizontal. Is it possible to push the block if , no matter how large the pushing force is? Explain quantitatively.
Answer
No, it is impossible to move the block. Key steps: (1) Maximum static friction is . (2) Forward pushing force is . (3) Motion requires , or . (4) If , then , making . Increasing increases normal force and friction faster than horizontal forward force, locking the block in place.