Resources

A solid cylindrical brass specimen of diameter d0=12.0 mmd_0 = 12.0\text{ mm} and gauge length L0=150.0 mmL_0 = 150.0\text{ mm} is placed under a tensile load within an axial testing machine. When an axial tension of F=18.5 kNF = 18.5\text{ kN} is applied, precision extensometers measure an axial elongation of ΔL=0.245 mm\Delta L = 0.245\text{ mm} and a simultaneous diameter reduction of Δd=−6.50×10−3 mm\Delta d = -6.50 \times 10^{-3}\text{ mm}. Reverse-engineer this empirical data to determine: (a) the Young's modulus EE of the brass specimen, and (b) Poisson's ratio ν\nu for this material.

Answer and steps

Final answer

(a) E=1.00×1011 PaE = 1.00 \times 10^{11}\text{ Pa}; (b) ν=0.332\nu = 0.332

Steps

Part (a): Calculate Young's Modulus (EE)

  1. Calculate the original cross-sectional area (A0A_0): The specimen has a circular cross-section with diameter d0=12.0 mm=0.0120 md_0 = 12.0\text{ mm} = 0.0120\text{ m}: A0=πd024=π(0.0120 m)24≈1.131×10−4 m2A_0 = \frac{\pi d_0^2}{4} = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.131 \times 10^{-4}\text{ m}^2
  2. Calculate the normal tensile stress (σ\sigma): Stress is defined as the applied tensile force divided by the initial cross-sectional area: σ=FA0=18.5×103 N1.131×10−4 m2≈1.636×108 Pa\sigma = \frac{F}{A_0} = \frac{18.5 \times 10^3\text{ N}}{1.131 \times 10^{-4}\text{ m}^2} \approx 1.636 \times 10^8\text{ Pa}
  3. Calculate the longitudinal (axial) strain (εaxial\varepsilon_{\text{axial}}): Axial strain is the ratio of elongation ΔL\Delta L to original gauge length L0L_0: εaxial=ΔLL0=0.245 mm150.0 mm≈1.633×10−3\varepsilon_{\text{axial}} = \frac{\Delta L}{L_0} = \frac{0.245\text{ mm}}{150.0\text{ mm}} \approx 1.633 \times 10^{-3}
  4. Determine Young's modulus (EE): By Hooke's Law for uniaxial stress in the elastic regime, Young's modulus is the ratio of axial stress to axial strain: E=σεaxial=1.636×108 Pa1.633×10−3≈1.00×1011 PaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{1.636 \times 10^8\text{ Pa}}{1.633 \times 10^{-3}} \approx 1.00 \times 10^{11}\text{ Pa}

Part (b): Calculate Poisson's Ratio (ν\nu)

  1. Calculate the lateral (transverse) strain (εlat\varepsilon_{\text{lat}}): The lateral strain corresponds to the proportional change in diameter: εlat=Δdd0=−6.50×10−3 mm12.0 mm≈−5.417×10−4\varepsilon_{\text{lat}} = \frac{\Delta d}{d_0} = \frac{-6.50 \times 10^{-3}\text{ mm}}{12.0\text{ mm}} \approx -5.417 \times 10^{-4}
  2. Compute Poisson's ratio (ν\nu): Poisson's ratio is defined as the negative ratio of transverse strain to axial strain under uniaxial tension: ν=−εlatεaxial=−−5.417×10−41.633×10−3≈0.332\nu = -\frac{\varepsilon_{\text{lat}}}{\varepsilon_{\text{axial}}} = -\frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}} \approx 0.332

(Pitfall to avoid: Poisson's ratio includes a negative sign by definition so that the material constant is a positive dimensionless value for standard materials that contract laterally under tension).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the diameter with the radius when calculating the cross-sectional area, using πd₀² instead of π(d₀/2)², which underestimates stress and Young's modulus by a factor of 4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=π⋅d02=π⋅(0.012 m)2=4.524×10−4 m2A = \pi \cdot d_0^2 = \pi \cdot (0.012\text{ m})^2 = 4.524 \times 10^{-4}\text{ m}^2

    Correct

    A0=πd024=π(0.0120 m)24≈1.131×10−4 m2A_0 = \frac{\pi d_0^2}{4} = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.131 \times 10^{-4}\text{ m}^2

    You treated the diameter as the radius in the circular area formula. The area of a circle in terms of diameter dd is A=πd24A = \frac{\pi d^2}{4} (or πr2\pi r^2 with r=d2r = \frac{d}{2}).

  2. Step 2

    σ=FA=18500 N4.524×10−4 m2=4.089×107 Pa\sigma = \frac{F}{A} = \frac{18500\text{ N}}{4.524 \times 10^{-4}\text{ m}^2} = 4.089 \times 10^7\text{ Pa}

    Correct

    σ=FA0=18.5×103 N1.131×10−4 m2≈1.636×108 Pa\sigma = \frac{F}{A_0} = \frac{18.5 \times 10^3\text{ N}}{1.131 \times 10^{-4}\text{ m}^2} \approx 1.636 \times 10^8\text{ Pa}

    You applied the stress definition correctly, but this value is affected by the 4-fold overestimation of cross-sectional area from Step 1.

  3. Step 3

    εaxial=ΔLL0=0.245 mm150.0 mm=1.633×10−3\varepsilon_{\text{axial}} = \frac{\Delta L}{L_0} = \frac{0.245\text{ mm}}{150.0\text{ mm}} = 1.633 \times 10^{-3}

  4. Step 4

    E=σεaxial=4.089×107 Pa1.633×10−3=2.50×1010 Pa=25.0 GPaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{4.089 \times 10^7\text{ Pa}}{1.633 \times 10^{-3}} = 2.50 \times 10^{10}\text{ Pa} = 25.0\text{ GPa}

    Correct

    E=σεaxial=1.636×108 Pa1.633×10−3≈1.00×1011 PaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{1.636 \times 10^8\text{ Pa}}{1.633 \times 10^{-3}} \approx 1.00 \times 10^{11}\text{ Pa}

    You correctly related stress and strain via Hooke's Law, but the resulting Young's modulus inherits the 4-fold reduction caused by the initial area calculation.

  5. Step 5

    εlateral=Δdd0=−6.50×10−3 mm12.0 mm=−5.417×10−4\varepsilon_{\text{lateral}} = \frac{\Delta d}{d_0} = \frac{-6.50 \times 10^{-3}\text{ mm}}{12.0\text{ mm}} = -5.417 \times 10^{-4}

  6. Step 6

    ν=−εlateralεaxial=−(−5.417×10−4)1.633×10−3=0.332\nu = \frac{-\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}} = \frac{-(-5.417 \times 10^{-4})}{1.633 \times 10^{-3}} = 0.332

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly defined normal stress σ=FA\sigma = \frac{F}{A} and axial strain εaxial=ΔLL0\varepsilon_{\text{axial}} = \frac{\Delta L}{L_0}.

You correctly computed both the axial strain and transverse lateral strain.

You used the negative sign in Poisson's ratio ν=−εlatεaxial\nu = -\frac{\varepsilon_{\text{lat}}}{\varepsilon_{\text{axial}}} to arrive at the correct positive value of 0.3320.332.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometry Formula Confusion

You substituted the specimen diameter directly into πr2\pi r^2 without dividing by 2 or dividing by 4.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing diameter dd with radius rr when writing the area formula for a circular cross-section, writing πd2\pi d^2 instead of πd24\frac{\pi d^2}{4}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Circular Cross-Section Area
  • For a circular cylinder of diameter dd, the cross-sectional area is A=πr2=π(d2)2=πd24A = \pi r^2 = \pi \left(\frac{d}{2}\right)^2 = \frac{\pi d^2}{4}.

  • Always check whether the given dimension is radius or diameter before substituting into πr2\pi r^2.

Scaling Check for Young's Modulus
  • Typical metals have Young's moduli in the range of 70 GPa70\text{ GPa} to 210 GPa210\text{ GPa} (brass is approximately 100 GPa100\text{ GPa}).

  • If your computed modulus for a metal yields around 25 GPa25\text{ GPa}, check whether an area factor of 4 was accidentally introduced.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. A0=πd024=π(0.0120 m)24≈1.131×10−4 m2A_0 = \frac{\pi d_0^2}{4} = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.131 \times 10^{-4}\text{ m}^2

  2. σ=FA0=18.5×103 N1.131×10−4 m2≈1.636×108 Pa\sigma = \frac{F}{A_0} = \frac{18.5 \times 10^3\text{ N}}{1.131 \times 10^{-4}\text{ m}^2} \approx 1.636 \times 10^8\text{ Pa}

  3. E=σεaxial=1.636×108 Pa1.633×10−3≈1.00×1011 Pa=100 GPaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{1.636 \times 10^8\text{ Pa}}{1.633 \times 10^{-3}} \approx 1.00 \times 10^{11}\text{ Pa} = 100\text{ GPa}

Final answer

(a) E=1.00×1011 PaE = 1.00 \times 10^{11}\text{ Pa} (100 GPa100\text{ GPa}); (b) ν=0.332\nu = 0.332

NEXT STEPS
Final Takeaways from Your Teacher
  • Before setting up stress calculations, write down explicitly whether each given dimension is a diameter or a radius.

  • Use A=πd24A = \frac{\pi d^2}{4} directly whenever diameters are provided to avoid radius conversion errors.

  • Compare resulting elastic modulus values against typical order-of-magnitude ranges for common engineering alloys.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the definition of Poisson's ratio by taking axial strain over lateral strain instead of lateral strain over axial strain.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=π⋅(d02)2=π⋅(0.006 m)2=1.131×10−4 m2  ⟹  σ=FA=18500 N1.131×10−4 m2=1.636×108 PaA = \pi \cdot \left(\frac{d_0}{2}\right)^2 = \pi \cdot (0.006\text{ m})^2 = 1.131 \times 10^{-4}\text{ m}^2 \implies \sigma = \frac{F}{A} = \frac{18500\text{ N}}{1.131 \times 10^{-4}\text{ m}^2} = 1.636 \times 10^8\text{ Pa}

  2. Step 2

    εaxial=ΔLL0=0.245 mm150.0 mm=1.633×10−3  ⟹  E=σεaxial=1.636×108 Pa1.633×10−3=1.00×1011 Pa=100 GPa\varepsilon_{\text{axial}} = \frac{\Delta L}{L_0} = \frac{0.245\text{ mm}}{150.0\text{ mm}} = 1.633 \times 10^{-3} \implies E = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{1.636 \times 10^8\text{ Pa}}{1.633 \times 10^{-3}} = 1.00 \times 10^{11}\text{ Pa} = 100\text{ GPa}

  3. Step 3

    εlateral=Δdd0=−6.50×10−3 mm12.0 mm=−5.417×10−4\varepsilon_{\text{lateral}} = \frac{\Delta d}{d_0} = \frac{-6.50 \times 10^{-3}\text{ mm}}{12.0\text{ mm}} = -5.417 \times 10^{-4}

  4. Step 4

    ν=−εaxialεlateral=−1.633×10−3−5.417×10−4=3.01\nu = -\frac{\varepsilon_{\text{axial}}}{\varepsilon_{\text{lateral}}} = -\frac{1.633 \times 10^{-3}}{-5.417 \times 10^{-4}} = 3.01

    Correct

    ν=−εlateralεaxial=−−5.417×10−41.633×10−3≈0.332\nu = -\frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}} = -\frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}} \approx 0.332

    You inverted the formula for Poisson's ratio. Poisson's ratio is defined as the negative ratio of lateral strain to axial strain (response over cause), not axial over lateral.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the cross-sectional area and normal stress.

You applied Hooke's law accurately to find Young's modulus as 1.00×1011 Pa1.00 \times 10^{11}\text{ Pa}.

You correctly calculated the lateral strain including its negative sign.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Poisson's Ratio Formula

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the numerator and denominator in the definition of Poisson's ratio. Poisson's ratio measures the lateral strain that occurs in response to an applied axial strain: ν=−εlateralεaxial\nu = -\frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}}. For stable isotropic materials, ν\nu must lie between 00 and 0.50.5, so obtaining a value of 3.013.01 indicates that the ratio was inverted.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Poisson's Ratio
  • Poisson's ratio is ν=−εtransverseεlongitudinal\nu = -\frac{\varepsilon_{\text{transverse}}}{\varepsilon_{\text{longitudinal}}}.

  • Always place the lateral (perpendicular/passive) strain in the numerator and the axial (parallel/driving) strain in the denominator.

Physical Bounds Check
  • For ordinary isotropic elastic materials in 3D, 0≤ν≤0.50 \le \nu \le 0.5.

  • If your calculated Poisson's ratio exceeds 0.50.5, check immediately whether you inverted the strain ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the standard definition of Poisson's ratio: ν=−εlateralεaxial\nu = -\frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}}.

  2. Substitute the previously calculated values: ν=−−5.417×10−41.633×10−3\nu = -\frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}}.

  3. Evaluate the quotient: ν≈0.332\nu \approx 0.332.

Final answer

(a) E=1.00×1011 PaE = 1.00 \times 10^{11}\text{ Pa}; (b) ν=0.332\nu = 0.332

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize Poisson's ratio as ν=−lateral strainaxial strain\nu = -\frac{\text{lateral strain}}{\text{axial strain}} (side effect divided by main effect).

  • Use the rule of thumb that ν\nu is typically between 0.250.25 and 0.350.35 for metals to instantly sanity-check your results.

OverviewACEpath Teacher's Diagnosis

03 The student omits the negative sign in the definition of Poisson's ratio, yielding an incorrect negative ratio.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=π⋅(d02)2=π⋅(0.006 m)2=1.131×10−4 m2  ⟹  σ=FA=18500 N1.131×10−4 m2=1.636×108 PaA = \pi \cdot \left(\frac{d_0}{2}\right)^2 = \pi \cdot (0.006\text{ m})^2 = 1.131 \times 10^{-4}\text{ m}^2 \implies \sigma = \frac{F}{A} = \frac{18500\text{ N}}{1.131 \times 10^{-4}\text{ m}^2} = 1.636 \times 10^8\text{ Pa}

  2. Step 2

    εaxial=ΔLL0=0.245 mm150.0 mm=1.633×10−3\varepsilon_{\text{axial}} = \frac{\Delta L}{L_0} = \frac{0.245\text{ mm}}{150.0\text{ mm}} = 1.633 \times 10^{-3}

  3. Step 3

    E=σεaxial=1.636×108 Pa1.633×10−3=1.00×1011 Pa=100 GPaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{1.636 \times 10^8\text{ Pa}}{1.633 \times 10^{-3}} = 1.00 \times 10^{11}\text{ Pa} = 100\text{ GPa}

  4. Step 4

    εlateral=Δdd0=−6.50×10−3 mm12.0 mm=−5.417×10−4\varepsilon_{\text{lateral}} = \frac{\Delta d}{d_0} = \frac{-6.50 \times 10^{-3}\text{ mm}}{12.0\text{ mm}} = -5.417 \times 10^{-4}

  5. Step 5

    ν=εlateralεaxial=−5.417×10−41.633×10−3=−0.332\nu = \frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}} = \frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}} = -0.332

    Correct

    ν=−εlateralεaxial=−−5.417×10−41.633×10−3≈0.332\nu = -\frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}} = -\frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}} \approx 0.332

    You omitted the negative sign in the formula for Poisson's ratio. By convention and definition, ν=−εtransverseεaxial\nu = -\frac{\varepsilon_{\text{transverse}}}{\varepsilon_{\text{axial}}}, which ensures that common materials undergoing lateral shrinkage under tension have a positive Poisson's ratio.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted all diameter and length units consistently to calculate the cross-sectional area and stress.

You correctly applied Hooke's law to obtain the Young's modulus E=1.00×1011 PaE = 1.00 \times 10^{11}\text{ Pa}.

You tracked the negative sign of the lateral diameter contraction accurately when finding transverse strain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of negative sign in definition of Poisson's ratio

You set up the ratio of transverse to axial strain accurately, but missed the required negative sign in the definition ν=−εlatεaxial\nu = -\frac{\varepsilon_{\text{lat}}}{\varepsilon_{\text{axial}}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the physical ratio of two strains of opposite signs with the formal constitutive definition of Poisson's ratio, which incorporates a minus sign so that standard passive materials have positive values (0<ν<0.50 < \nu < 0.5).

REASONING PATH
Your ACEpath teacher’s suggested approach
Poisson's Ratio Definition
  • For uniaxial loading, Poisson's ratio is defined as ν=−εtransverseεaxial\nu = -\frac{\varepsilon_{\text{transverse}}}{\varepsilon_{\text{axial}}}.

  • Always include the minus sign in the formula so that lateral thinning under tensile elongation yields a positive material constant.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ν=−εlateralεaxial\nu = -\frac{\varepsilon_{\text{lateral}}}{\varepsilon_{\text{axial}}}

  2. ν=−−5.417×10−41.633×10−3=+0.332\nu = -\frac{-5.417 \times 10^{-4}}{1.633 \times 10^{-3}} = +0.332

Final answer

(a) E=1.00×1011 PaE = 1.00 \times 10^{11}\text{ Pa}; (b) ν=0.332\nu = 0.332

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that ordinary engineering materials (such as metals, plastics, and ceramics) have positive Poisson's ratios typically between 0.250.25 and 0.350.35.

  • Whenever an axial tension causes transverse contraction, use ν=−εlatεlong\nu = -\frac{\varepsilon_{\text{lat}}}{\varepsilon_{\text{long}}} to obtain a positive value.

Lock it in

Similar question

01

A cylindrical copper rod of diameter d=10.0 mmd = 10.0\text{ mm} supports a tensile load of F=7.85 kNF = 7.85\text{ kN}. Calculate the tensile stress σ\sigma in the rod.

Answer
  1. Area: A=πd24=π(0.010 m)24≈7.854×10−5 m2A = \frac{\pi d^2}{4} = \frac{\pi (0.010\text{ m})^2}{4} \approx 7.854 \times 10^{-5}\text{ m}^2.
  2. Stress: σ=FA=7850 N7.854×10−5 m2≈1.00×108 Pa=100 MPa\sigma = \frac{F}{A} = \frac{7850\text{ N}}{7.854 \times 10^{-5}\text{ m}^2} \approx 1.00 \times 10^8\text{ Pa} = 100\text{ MPa}.
02

A steel tie rod of diameter d0=16.0 mmd_0 = 16.0\text{ mm} and original length L0=2.00 mL_0 = 2.00\text{ m} experiences an axial tensile load of 30.0 kN30.0\text{ kN}. If the measured elongation is ΔL=1.48 mm\Delta L = 1.48\text{ mm}, find the Young's modulus EE of the steel.

Answer
  1. Area: A0=π(0.016 m)24≈2.011×10−4 m2A_0 = \frac{\pi (0.016\text{ m})^2}{4} \approx 2.011 \times 10^{-4}\text{ m}^2.
  2. Stress: σ=30.0×103 N2.011×10−4 m2≈1.492×108 Pa\sigma = \frac{30.0 \times 10^3\text{ N}}{2.011 \times 10^{-4}\text{ m}^2} \approx 1.492 \times 10^8\text{ Pa}.
  3. Strain: ε=ΔLL0=1.48×10−3 m2.00 m=7.40×10−4\varepsilon = \frac{\Delta L}{L_0} = \frac{1.48 \times 10^{-3}\text{ m}}{2.00\text{ m}} = 7.40 \times 10^{-4}.
  4. Young's modulus: E=σε=1.492×108 Pa7.40×10−4≈2.02×1011 Pa=202 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.492 \times 10^8\text{ Pa}}{7.40 \times 10^{-4}} \approx 2.02 \times 10^{11}\text{ Pa} = 202\text{ GPa}.
03

An aluminum cylinder with initial diameter d0=25.0 mmd_0 = 25.0\text{ mm} and length L0=200.0 mmL_0 = 200.0\text{ mm} is loaded in tension. Under load, its length increases by 0.160 mm0.160\text{ mm} while its diameter contracts by 6.60×10−3 mm6.60 \times 10^{-3}\text{ mm}. If the applied force is 27.5 kN27.5\text{ kN}, find both Young's modulus EE and Poisson's ratio ν\nu.

Answer
  1. Axial strain: εaxial=0.160 mm200.0 mm=8.00×10−4\varepsilon_{\text{axial}} = \frac{0.160\text{ mm}}{200.0\text{ mm}} = 8.00 \times 10^{-4}.
  2. Lateral strain: εlat=−6.60×10−3 mm25.0 mm=−2.64×10−4\varepsilon_{\text{lat}} = \frac{-6.60 \times 10^{-3}\text{ mm}}{25.0\text{ mm}} = -2.64 \times 10^{-4}.
  3. Poisson's ratio: ν=−εlatεaxial=−−2.64×10−48.00×10−4=0.330\nu = -\frac{\varepsilon_{\text{lat}}}{\varepsilon_{\text{axial}}} = -\frac{-2.64 \times 10^{-4}}{8.00 \times 10^{-4}} = 0.330.
  4. Area: A0=π(0.025 m)24≈4.909×10−4 m2A_0 = \frac{\pi (0.025\text{ m})^2}{4} \approx 4.909 \times 10^{-4}\text{ m}^2.
  5. Stress: σ=2.75×104 N4.909×10−4 m2≈5.602×107 Pa\sigma = \frac{2.75 \times 10^4\text{ N}}{4.909 \times 10^{-4}\text{ m}^2} \approx 5.602 \times 10^7\text{ Pa}.
  6. Young's modulus: E=σεaxial=5.602×107 Pa8.00×10−4≈7.00×1010 Pa=70.0 GPaE = \frac{\sigma}{\varepsilon_{\text{axial}}} = \frac{5.602 \times 10^7\text{ Pa}}{8.00 \times 10^{-4}} \approx 7.00 \times 10^{10}\text{ Pa} = 70.0\text{ GPa}.
Loading workspace…