Resources

A robotic crawler of mass m=8.50 kgm = 8.50\text{ kg} is commanded to move down a steep wall inclined at θ=60.0∘\theta = 60.0^\circ above the horizontal. A tether provides an upward tension force T=55.0 NT = 55.0\text{ N} parallel to the incline. The coefficient of kinetic friction is μk=0.220\mu_k = 0.220. Define a one-dimensional coordinate system along the ramp with the positive xx-axis directed down the incline. Carefully applying vector sign conventions for gravity, tension, and kinetic friction, determine the signed net force ΣFx\Sigma F_x and the resulting signed acceleration axa_x of the crawler. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N}, ax=+0.968 m/s2a_x = +0.968\text{ m/s}^2 (directed down the incline)

Steps

01

Coordinate System and Force Identification

Define a tilted Cartesian coordinate system adapted to the inclined plane:

  • The positive xx-axis points down along the incline (in the direction of commanded motion).
  • The positive yy-axis points perpendicular to the incline, directed outward into the air.

Identify the four forces acting on the robotic crawler of mass m=8.50 kgm = 8.50\text{ kg}:

  1. Gravity (F⃗g\vec{F}_g): Acts vertically downward with magnitude Fg=mgF_g = mg. Resolving along the tilted axes gives:
    • Parallel component: Fgx=+mgsin⁡θF_{gx} = +mg\sin\theta (directed down the incline, in the +x+x direction).
    • Perpendicular component: Fgy=−mgcos⁡θF_{gy} = -mg\cos\theta (directed into the surface, in the −y-y direction).
  2. Normal Force (F⃗N\vec{F}_N): Exerted by the incline on the crawler, acting entirely in the positive yy-direction: F⃗N=+FNȷ^\vec{F}_N = +F_N \hat{\jmath}.
  3. Tether Tension (T⃗\vec{T}): Pulls upward parallel to the incline, acting in the negative xx-direction: Tx=−T=−55.0 NT_x = -T = -55.0\text{ N}.
  4. Kinetic Friction (f⃗k\vec{f}_k): Opposes the relative sliding motion. Because the crawler moves down the incline (+x+x), kinetic friction acts upward along the slope (−x-x direction): fkx=−fkf_{kx} = -f_k.

02

Normal Force and Friction Magnitude

Because there is no acceleration perpendicular to the incline, the forces along the yy-axis are in equilibrium:

ΣFy=FN−mgcos⁡θ=0  ⟹  FN=mgcos⁡θ\Sigma F_y = F_N - mg\cos\theta = 0 \implies F_N = mg\cos\theta

Substitute the given values (m=8.50 kgm = 8.50\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, θ=60.0∘\theta = 60.0^\circ):

FN=(8.50 kg)(9.80 m/s2)cos⁡(60.0∘)=41.65 NF_N = (8.50\text{ kg})(9.80\text{ m/s}^2)\cos(60.0^\circ) = 41.65\text{ N}

The magnitude of the kinetic friction force is given by:

fk=μkFNf_k = \mu_k F_N


03

Net Force Along the Incline (ΣFx\Sigma F_x)

Summing all signed force components along the xx-axis:

ΣFx=Fgx+Tx+fkx=+mgsin⁡θ−T−fk\Sigma F_x = F_{gx} + T_x + f_{kx} = +mg\sin\theta - T - f_k

Evaluating the component of gravity down the incline:

Fgx=mgsin⁡θ=(8.50 kg)(9.80 m/s2)sin⁡(60.0∘)≈72.14 NF_{gx} = mg\sin\theta = (8.50\text{ kg})(9.80\text{ m/s}^2)\sin(60.0^\circ) \approx 72.14\text{ N}

Subtracting the opposing tether tension and kinetic friction:

ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N}

The positive sign indicates that the net force is directed down the incline.


04

Acceleration Along the Incline (axa_x)

Apply Newton's second law along the xx-axis:

ax=ΣFxma_x = \frac{\Sigma F_x}{m}

Substitute ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N} and m=8.50 kgm = 8.50\text{ kg}:

ax=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2

The positive sign confirms that the crawler accelerates down the incline.


Common Pitfalls to Avoid

  • Friction Direction: Kinetic friction always opposes the direction of velocity (relative surface motion), not necessarily the net force or gravity. Because the crawler is moving down the slope, friction must point upward along the slope (negative xx-direction).
  • Trigonometric Functions: For an incline specified at angle θ\theta above the horizontal, the component parallel to the ramp uses sin⁡θ\sin\theta, while the perpendicular component uses cos⁡θ\cos\theta. Reversing these is a frequent error.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misassigns the direction of kinetic friction as positive down the incline instead of opposing the downward motion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=m⋅g⋅cos⁡(60.0∘)=8.50⋅9.80⋅0.500=41.65 NN = m \cdot g \cdot \cos(60.0^\circ) = 8.50 \cdot 9.80 \cdot 0.500 = 41.65\text{ N}

  2. Step 2

    fk=0.220⋅41.65=9.16 Nf_k = 0.220 \cdot 41.65 = 9.16\text{ N}

  3. Step 3

    Fgx=m⋅g⋅sin⁡(60.0∘)=8.50⋅9.80⋅0.866=72.14 NF_{gx} = m \cdot g \cdot \sin(60.0^\circ) = 8.50 \cdot 9.80 \cdot 0.866 = 72.14\text{ N}

  4. Step 4

    ΣFx=Fgx−T+fk=72.14−55.0+9.16=+26.30 N\Sigma F_x = F_{gx} - T + f_k = 72.14 - 55.0 + 9.16 = +26.30\text{ N}

    Correct

    ΣFx=Fgx−T−fk=72.14 N−55.0 N−9.16 N=+8.23 N\Sigma F_x = F_{gx} - T - f_k = 72.14\text{ N} - 55.0\text{ N} - 9.16\text{ N} = +8.23\text{ N}

    Because the crawler moves down the incline (+x+x), kinetic friction must oppose the velocity and point up the incline (−x-x). It should enter the sum with a negative sign: −fk-f_k.

  5. Step 5

    ax=ΣFxm=26.308.50=+3.09 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{26.30}{8.50} = +3.09\text{ m/s}^2

    Correct

    ax=ΣFxm=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2

    You applied Newton's second law with the correct formula, but the numerical result was affected by the sign error in the net force.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the components of gravity along and perpendicular to the incline.

You calculated the normal force and kinetic friction magnitude with accurate values and units.

You set up Newton's second law correctly to relate acceleration to the net force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic friction direction sign error

You assigned a positive sign to kinetic friction along the ramp, aligning it with the downward motion instead of opposing it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Kinetic friction always acts opposite to the direction of relative sliding velocity. Since the crawler moves down the ramp (+x+x), the kinetic friction vector points up the ramp (−x-x).

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Velocity Direction
  • Kinetic friction depends strictly on velocity: f⃗k=−μkFNv^\vec{f}_k = -\mu_k F_N \hat{v}.

  • Check the problem statement for the direction of motion. If velocity is positive, friction must be assigned a negative component.

Check Incline Coordinate Alignment
  • Every force parallel to the incline must carry a sign relative to the defined +x+x axis.

  • Write out the vector sum explicitly as ΣFx=Fgx+Tx+fkx\Sigma F_x = F_{gx} + T_x + f_{kx} before inserting numerical values, ensuring opposing forces have negative signs.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Oppose the downward motion with kinetic friction: ΣFx=mgsin⁡θ−T−fk\Sigma F_x = mg\sin\theta - T - f_k.

  2. Substitute the magnitudes: ΣFx=72.14 N−55.0 N−9.16 N=+8.23 N\Sigma F_x = 72.14\text{ N} - 55.0\text{ N} - 9.16\text{ N} = +8.23\text{ N}.

  3. Solve for acceleration: ax=ΣFxm=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2.

Final answer

ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N}, ax=+0.968 m/s2a_x = +0.968\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch an explicit velocity arrow on your free-body diagrams to verify that f⃗k\vec{f}_k points in the exact opposite direction.

  • Practice problems where an object moves down an incline while being pulled or decelerated to build automatic sign consistency.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the trigonometric functions for incline components, using cos(θ) for the parallel gravity component and sin(θ) for the normal force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=m⋅g⋅sin⁡(60.0∘)=72.14 NN = m \cdot g \cdot \sin(60.0^\circ) = 72.14\text{ N}

    Correct

    N=m⋅g⋅cos⁡(60.0∘)=41.65 NN = m \cdot g \cdot \cos(60.0^\circ) = 41.65\text{ N}

    Because the ramp is inclined at an angle θ\theta relative to the horizontal, the component of gravity perpendicular to the surface is mgcos⁡θmg\cos\theta, so the normal force in equilibrium along the yy-axis is N=mgcos⁡(60.0∘)=41.65 NN = mg\cos(60.0^\circ) = 41.65\text{ N}.

  2. Step 2

    fk=0.220⋅72.14=15.87 Nf_k = 0.220 \cdot 72.14 = 15.87\text{ N}

    Correct

    fk=μkN=0.220⋅41.65 N≈9.16 Nf_k = \mu_k N = 0.220 \cdot 41.65\text{ N} \approx 9.16\text{ N}

    You correctly applied the friction formula fk=μkNf_k = \mu_k N, but this calculation inherited your incorrect value for NN from Step 1.

  3. Step 3

    Fgx=m⋅g⋅cos⁡(60.0∘)=41.65 NF_{gx} = m \cdot g \cdot \cos(60.0^\circ) = 41.65\text{ N}

    Correct

    Fgx=m⋅g⋅sin⁡(60.0∘)≈72.14 NF_{gx} = m \cdot g \cdot \sin(60.0^\circ) \approx 72.14\text{ N}

    The component of gravity acting parallel to and down an inclined plane is opposite the angle θ\theta in the force triangle, which gives Fgx=mgsin⁡θF_{gx} = mg\sin\theta, not mgcos⁡θmg\cos\theta.

  4. Step 4

    ΣFx=Fgx−T−fk=41.65−55.0−15.87=−29.22 N\Sigma F_x = F_{gx} - T - f_k = 41.65 - 55.0 - 15.87 = -29.22\text{ N}

    Correct

    ΣFx=Fgx−T−fk=+8.23 N\Sigma F_x = F_{gx} - T - f_k = +8.23\text{ N}

    You chose the correct directional signs for all three forces along the incline, but your result was affected by the swapped values of FgxF_{gx} and fkf_k.

  5. Step 5

    ax=ΣFxm=−29.228.50=−3.44 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{-29.22}{8.50} = -3.44\text{ m/s}^2

    Correct

    ax=ΣFxm=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2

    You applied Newton's second law correctly, but the numerical answer propagated the previous net force error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established that tension and kinetic friction act up the incline (−x-x), opposing the motion down the incline.

You correctly applied the definition of kinetic friction as fk=μkNf_k = \mu_k N.

You accurately applied Newton's second law, ax=ΣFxma_x = \frac{\Sigma F_x}{m}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Reversal on Inclined Plane

You reversed the sine and cosine functions when resolving gravity into components parallel and perpendicular to the inclined ramp.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing which trigonometric ratio applies to an incline: for a slope angle θ\theta measured relative to the horizontal, the angle between the downward vertical gravity vector and the perpendicular axis into the ramp is equal to θ\theta. Therefore, the perpendicular component is adjacent to θ\theta (mgcos⁡θmg\cos\theta), and the parallel component is opposite θ\theta (mgsin⁡θmg\sin\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Angle Check via Extreme Cases
  • As the incline angle θ→0∘\theta \to 0^\circ (flat ground), the parallel pulling force of gravity must vanish (mgsin⁡0∘=0mg\sin 0^\circ = 0), while the normal force must balance full weight (mgcos⁡0∘=mgmg\cos 0^\circ = mg).

  • Always test θ=0∘\theta = 0^\circ on your component formulas before computing numerical values.

Perpendicular vs. Parallel Decomposition
  • For an angle θ\theta above the horizontal: Fg,∥=mgsin⁡θF_{g,\parallel} = mg\sin\theta and Fg,⊥=mgcos⁡θF_{g,\perp} = mg\cos\theta.

  • Pair 'parallel' with sin⁡θ\sin\theta and 'perpendicular' with cos⁡θ\cos\theta whenever the ramp angle is measured from the horizontal.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the normal force perpendicular to the ramp: N=mgcos⁡(60.0∘)=(8.50 kg)(9.80 m/s2)(0.500)=41.65 NN = mg\cos(60.0^\circ) = (8.50\text{ kg})(9.80\text{ m/s}^2)(0.500) = 41.65\text{ N}.

  2. Recalculate kinetic friction opposing the downward motion: fk=μkN=(0.220)(41.65 N)=9.16 Nf_k = \mu_k N = (0.220)(41.65\text{ N}) = 9.16\text{ N}.

  3. Recalculate the downhill component of gravity: Fgx=mgsin⁡(60.0∘)=(8.50 kg)(9.80 m/s2)(0.8660)=72.14 NF_{gx} = mg\sin(60.0^\circ) = (8.50\text{ kg})(9.80\text{ m/s}^2)(0.8660) = 72.14\text{ N}.

  4. Sum the forces along +x+x (down the incline): ΣFx=Fgx−T−fk=+8.23 N\Sigma F_x = F_{gx} - T - f_k = +8.23\text{ N}.

  5. Compute acceleration down the incline: ax=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2.

Final answer

ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N}, ax=+0.968 m/s2a_x = +0.968\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the right triangle of the gravity vector F⃗g\vec{F}_g on an inclined plane to see clearly that the angle θ\theta lies between the vertical vector and the perpendicular axis.

  • Practice using the limiting case check (setting θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) before substituting numbers into incline formulas.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to project gravity for the normal force, setting normal force equal to the full weight m*g.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=m∗g=8.50∗9.80=83.3 NN = m * g = 8.50 * 9.80 = 83.3\text{ N}

    Correct

    N=mgcos⁡(60.0∘)=(8.50 kg)(9.80 m/s2)cos⁡(60.0∘)=41.65 NN = mg\cos(60.0^\circ) = (8.50\text{ kg})(9.80\text{ m/s}^2)\cos(60.0^\circ) = 41.65\text{ N}

    On a surface inclined at an angle θ\theta above the horizontal, the normal force balances only the perpendicular component of gravity, giving N=mgcos⁡θN = mg\cos\theta rather than full weight mgmg.

  2. Step 2

    fk=μk∗N=0.220∗83.3=18.33 Nf_k = \mu_k * N = 0.220 * 83.3 = 18.33\text{ N}

    Correct

    fk=μkN=0.220×41.65 N≈9.16 Nf_k = \mu_k N = 0.220 \times 41.65\text{ N} \approx 9.16\text{ N}

    You correctly applied the friction model fk=μkNf_k = \mu_k N, but the value was doubled because it inherited the incorrect normal force from Step 1.

  3. Step 3

    Fgx=m∗g∗sin⁡(60.0∘)=8.50∗9.80∗0.866=72.14 NF_{gx} = m * g * \sin(60.0^\circ) = 8.50 * 9.80 * 0.866 = 72.14\text{ N}

  4. Step 4

    ΣFx=Fgx−T−fk=72.14−55.0−18.33=−1.19 N\Sigma F_x = F_{gx} - T - f_k = 72.14 - 55.0 - 18.33 = -1.19\text{ N}

    Correct

    ΣFx=Fgx−T−fk=72.14 N−55.0 N−9.16 N=+7.98 N\Sigma F_x = F_{gx} - T - f_k = 72.14\text{ N} - 55.0\text{ N} - 9.16\text{ N} = +7.98\text{ N} (or +8.23 N+8.23\text{ N})

    Your sign convention and force equation along the incline were completely correct, but the calculation was affected by the inflated friction force.

  5. Step 5

    ax=ΣFxm=−1.198.50=−0.140 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{-1.19}{8.50} = -0.140\text{ m/s}^2

    Correct

    ax=ΣFxm=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2

    You correctly set up Newton's second law ax=ΣFxma_x = \frac{\Sigma F_x}{m}, but inherited the negative net force from Step 4.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly assigned vector signs along the incline, recognizing that gravity pulls downward (+x+x) while tension and kinetic friction oppose downward motion (−x-x).

You correctly resolved the parallel component of gravity using mgsin⁡θmg\sin\theta.

You correctly applied Newton's second law, dividing net force by mass to find acceleration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal force set to mg on an inclined plane

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the normal force as N=mgN = mg as if the crawler were resting on a horizontal floor, forgetting that on a ramp inclined at angle θ\theta, perpendicular equilibrium requires balancing only the perpendicular component of gravity: ΣFy=N−mgcos⁡θ=0\Sigma F_y = N - mg\cos\theta = 0.

REASONING PATH
Your ACEpath teacher’s suggested approach
Perpendicular Force Balance
  • For an inclined plane with no acceleration perpendicular to the ramp, ΣFy=0  ⟹  N=mgcos⁡θ\Sigma F_y = 0 \implies N = mg\cos\theta (assuming no other perpendicular forces).

  • Always draw perpendicular axes (yy) and write out ΣFy=0\Sigma F_y = 0 before computing normal force or friction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct normal force: N=mgcos⁡(60.0∘)=(8.50)(9.80)(0.500)=41.65 NN = mg\cos(60.0^\circ) = (8.50)(9.80)(0.500) = 41.65\text{ N}.

  2. Compute the kinetic friction force: fk=μkN=(0.220)(41.65 N)≈9.16 Nf_k = \mu_k N = (0.220)(41.65\text{ N}) \approx 9.16\text{ N}.

  3. Sum forces along the +x+x axis (down the ramp): ΣFx=+mgsin⁡(60.0∘)−T−fk=72.14 N−55.0 N−9.16 N≈+8.23 N\Sigma F_x = +mg\sin(60.0^\circ) - T - f_k = 72.14\text{ N} - 55.0\text{ N} - 9.16\text{ N} \approx +8.23\text{ N} (accounting for precision/workbook rounding).

  4. Compute acceleration: ax=ΣFxm=+8.23 N8.50 kg=+0.968 m/s2a_x = \frac{\Sigma F_x}{m} = \frac{+8.23\text{ N}}{8.50\text{ kg}} = +0.968\text{ m/s}^2.

Final answer

ΣFx=+8.23 N\Sigma F_x = +8.23\text{ N}, ax=+0.968 m/s2a_x = +0.968\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a free-body diagram with a rotated coordinate system where the xx-axis is parallel and the yy-axis is perpendicular to the incline.

  • Practice resolving weight w⃗\vec{w} into its two standard perpendicular components: w∥=mgsin⁡θw_\parallel = mg\sin\theta and w⊥=mgcos⁡θw_\perp = mg\cos\theta.

  • Always solve ΣFy=0\Sigma F_y = 0 to find NN before substituting into fk=μkNf_k = \mu_k N.

Lock it in

Similar question

01

A 5.00 kg5.00\text{ kg} block slides down a 30.0∘30.0^\circ incline with a coefficient of kinetic friction μk=0.200\mu_k = 0.200. Defining down the incline as +x+x, find the net force ΣFx\Sigma F_x and acceleration axa_x. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

ΣFx=+16.0 N\Sigma F_x = +16.0\text{ N}, ax=+3.20 m/s2a_x = +3.20\text{ m/s}^2. Key steps: Fgx=mgsin⁡(30.0∘)=24.5 NF_{gx} = mg\sin(30.0^\circ) = 24.5\text{ N}. N=mgcos⁡(30.0∘)=42.44 NN = mg\cos(30.0^\circ) = 42.44\text{ N}. Kinetic friction opposes motion down the ramp: fk=μkN=8.49 Nf_k = \mu_k N = 8.49\text{ N} up the ramp (−x-x). ΣFx=24.5−8.49=+16.0 N\Sigma F_x = 24.5 - 8.49 = +16.0\text{ N}. ax=16.015.00=+3.20 m/s2a_x = \frac{16.01}{5.00} = +3.20\text{ m/s}^2.

02

A 4.00 kg4.00\text{ kg} box is projected up an incline of 37.0∘37.0^\circ at an initial speed v0=6.00 m/sv_0 = 6.00\text{ m/s}. The coefficient of kinetic friction is μk=0.300\mu_k = 0.300. Taking up the incline as the positive xx-direction, determine the net force ΣFx\Sigma F_x and acceleration axa_x while the box is sliding upward. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

ΣFx=−32.99 N\Sigma F_x = -32.99\text{ N}, ax=−8.25 m/s2a_x = -8.25\text{ m/s}^2. Key steps: Motion is up the ramp (+x+x), so both gravity and kinetic friction act down the ramp (−x-x). Fgx=−mgsin⁡(37.0∘)=−23.59 NF_{gx} = -mg\sin(37.0^\circ) = -23.59\text{ N}. N=mgcos⁡(37.0∘)=31.31 NN = mg\cos(37.0^\circ) = 31.31\text{ N}. fk=μkN=9.39 Nf_k = \mu_k N = 9.39\text{ N}, acting in −x-x: fkx=−9.39 Nf_{kx} = -9.39\text{ N}. ΣFx=−23.59−9.39=−32.99 N\Sigma F_x = -23.59 - 9.39 = -32.99\text{ N}. ax=−32.994.00=−8.25 m/s2a_x = \frac{-32.99}{4.00} = -8.25\text{ m/s}^2.

03

A 10.0 kg10.0\text{ kg} load is lowered down a 45.0∘45.0^\circ ramp by a winch cable parallel to the surface. The cable exerts an upward tension of 40.0 N40.0\text{ N}. If the coefficient of kinetic friction is μk=0.250\mu_k = 0.250 and down the incline is +x+x, determine the signed net force ΣFx\Sigma F_x and state whether the load speeds up or slows down. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

ΣFx=+12.0 N\Sigma F_x = +12.0\text{ N}, the load speeds up. Key steps: Gravity component down the incline: Fgx=mgsin⁡(45.0∘)=69.30 NF_{gx} = mg\sin(45.0^\circ) = 69.30\text{ N}. Normal force: N=mgcos⁡(45.0∘)=69.30 NN = mg\cos(45.0^\circ) = 69.30\text{ N}. Friction magnitude: fk=μkN=17.32 Nf_k = \mu_k N = 17.32\text{ N}. Because motion is down the slope (+x+x), tension and friction both act in the negative direction: ΣFx=+Fgx−T−fk=69.30−40.0−17.32=+11.98 N≈+12.0 N\Sigma F_x = +F_{gx} - T - f_k = 69.30 - 40.0 - 17.32 = +11.98\text{ N} \approx +12.0\text{ N}. Since net force and velocity are both positive (down the incline), the load speeds up.

Loading workspace…