Resources

A vinyl record rotates on a turntable at a constant angular speed of 3313 rpm33\frac{1}{3}\text{ rpm}. Track A is recorded near the outer perimeter at a radius of rA=14.4 cmr_A = 14.4\text{ cm}, while Track B is recorded near the inner label at a radius of rB=6.00 cmr_B = 6.00\text{ cm}. A student incorrectly assumes that both tracks move past the stylus at the same linear speed because the record is a single rigid body with a constant period of rotation. (a) Determine the identical angular speed ω\omega of the record in rad/s\text{rad/s}. (b) Calculate the linear speed of the stylus relative to the groove for Track A (vAv_A) and Track B (vBv_B). (c) Determine the ratio of linear speeds vAvB\frac{v_A}{v_B}. Round values to three significant figures.

Answer and steps

Final answer

(a) ω=3.49 rad/s\omega = 3.49\text{ rad/s}; (b) vA=0.503 m/sv_A = 0.503\text{ m/s}, vB=0.209 m/sv_B = 0.209\text{ m/s}; (c) vAvB=2.40\frac{v_A}{v_B} = 2.40

Steps

Part (a): Convert Angular Speed to rad/s\text{rad/s}

The angular speed of an object in revolutions per minute (rpm\text{rpm}) can be converted to radians per second (rad/s\text{rad/s}) using the conversion factors:

  • 1 revolution=2π radians1\text{ revolution} = 2\pi\text{ radians}
  • 1 minute=60 seconds1\text{ minute} = 60\text{ seconds}

Given that the rotation rate is 3313 rpm=1003 rpm33\frac{1}{3}\text{ rpm} = \frac{100}{3}\text{ rpm}:

ω=(1003revmin)⋅(2π rad1 rev)⋅(1 min60 s)\omega = \left(\frac{100}{3}\frac{\text{rev}}{\text{min}}\right) \cdot \left(\frac{2\pi\text{ rad}}{1\text{ rev}}\right) \cdot \left(\frac{1\text{ min}}{60\text{ s}}\right)

ω=100⋅2π3⋅60=200π180=10π9 rad/s≈3.49 rad/s\omega = \frac{100 \cdot 2\pi}{3 \cdot 60} = \frac{200\pi}{180} = \frac{10\pi}{9}\text{ rad/s} \approx 3.49\text{ rad/s}


Part (b): Calculate the Linear Speeds vAv_A and vBv_B

For any point rotating on a rigid body at a distance rr from the axis of rotation, the linear (tangential) speed vv is directly proportional to its radius:

v=ωrv = \omega r

First, convert the radial distances from centimeters to meters:

  • rA=14.4 cm=0.144 mr_A = 14.4\text{ cm} = 0.144\text{ m}
  • rB=6.00 cm=0.0600 mr_B = 6.00\text{ cm} = 0.0600\text{ m}

Now calculate each linear speed using the unrounded value ω=10π9 rad/s\omega = \frac{10\pi}{9}\text{ rad/s}:

  • For Track A: vA=ωrA=(10π9 rad/s)(0.144 m)≈0.503 m/sv_A = \omega r_A = \left(\frac{10\pi}{9}\text{ rad/s}\right)(0.144\text{ m}) \approx 0.503\text{ m/s}
  • For Track B: vB=ωrB=(10π9 rad/s)(0.0600 m)≈0.209 m/sv_B = \omega r_B = \left(\frac{10\pi}{9}\text{ rad/s}\right)(0.0600\text{ m}) \approx 0.209\text{ m/s}

Common Pitfall: A rigid body shares the same angular speed ω\omega and period of rotation TT across all points, but it does not share the same linear speed vv. Points farther from the center must travel a larger circumference in the same amount of time, resulting in a higher linear speed.


Part (c): Determine the Ratio vAvB\frac{v_A}{v_B}

Since both tracks share the exact same angular speed ω\omega, the ratio of their linear speeds simplifies directly to the ratio of their radial distances:

vAvB=ωrAωrB=rArB\frac{v_A}{v_B} = \frac{\omega r_A}{\omega r_B} = \frac{r_A}{r_B}

Substitute the given radii:

vAvB=14.4 cm6.00 cm=2.40\frac{v_A}{v_B} = \frac{14.4\text{ cm}}{6.00\text{ cm}} = 2.40

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misremembers the rotational conversion factor by omitting 2π, incorrectly dividing rpm only by 60 to find angular speed in rad/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=33.3360  ⟹  ω=0.556 rad/s\omega = \frac{33.33}{60} \implies \omega = 0.556\text{ rad/s}

    Correct

    ω=3313 rpm×2π rad1 rev×1 min60 s=10π9 rad/s≈3.49 rad/s\omega = 33\frac{1}{3}\text{ rpm} \times \frac{2\pi\text{ rad}}{1\text{ rev}} \times \frac{1\text{ min}}{60\text{ s}} = \frac{10\pi}{9}\text{ rad/s} \approx 3.49\text{ rad/s}

    You divided the rotational frequency by 6060, which converts revolutions per minute to revolutions per second (hertz), but you forgot to multiply by 2π rad/rev2\pi\text{ rad/rev} to obtain angular speed in rad/s\text{rad/s}.

  2. Step 2

    rA=0.144 m,  rB=0.060 m  ⟹  vA=ωrA=(0.556)(0.144)=0.0801 m/s,  vB=ωrB=(0.556)(0.060)=0.0334 m/sr_A = 0.144\text{ m},\; r_B = 0.060\text{ m} \implies v_A = \omega r_A = (0.556)(0.144) = 0.0801\text{ m/s},\; v_B = \omega r_B = (0.556)(0.060) = 0.0334\text{ m/s}

    Correct

    vA=ωrA=(3.49 rad/s)(0.144 m)≈0.503 m/s,  vB=ωrB=(3.49 rad/s)(0.0600 m)≈0.209 m/sv_A = \omega r_A = (3.49\text{ rad/s})(0.144\text{ m}) \approx 0.503\text{ m/s},\; v_B = \omega r_B = (3.49\text{ rad/s})(0.0600\text{ m}) \approx 0.209\text{ m/s}

    Your formula v=ωrv = \omega r and radius unit conversions are completely correct, but your numerical speeds inherit the understated angular speed from part (a).

  3. Step 3

    vAvB=0.08010.0334=2.40\frac{v_A}{v_B} = \frac{0.0801}{0.0334} = 2.40

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted both radii from centimeters to meters.

You selected and applied the correct formula relating linear and angular speed, v=ωrv = \omega r.

You correctly computed the final ratio vAvB=2.40\frac{v_A}{v_B} = 2.40.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion: Missing $2\pi$ Factor

You divided by 6060 to switch minutes to seconds, but omitted the 2π2\pi factor needed to turn revolutions into radians.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing rotational frequency (ff in rev/s\text{rev/s}) with angular velocity (ω\omega in rad/s\text{rad/s}). Dividing rpm\text{rpm} by 6060 gives frequency in rev/s\text{rev/s}, which must still be multiplied by 2π2\pi because each complete revolution sweeps through 2π radians2\pi\text{ radians}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check angular conversion dimensions
  • 1 rev=2π rad1\text{ rev} = 2\pi\text{ rad} and 1 min=60 s1\text{ min} = 60\text{ s}, so ω (rad/s)=rpm×2π60\omega\,(\text{rad/s}) = \text{rpm} \times \frac{2\pi}{60}.

  • Always write out both conversion factors explicitly with cancelling units: (revmin)⋅(2π rad1 rev)⋅(1 min60 s)\left(\frac{\text{rev}}{\text{min}}\right) \cdot \left(\frac{2\pi\text{ rad}}{1\text{ rev}}\right) \cdot \left(\frac{1\text{ min}}{60\text{ s}}\right).

Distinguish $f$ from $\omega$
  • Rotational frequency f=rpm60f = \frac{\text{rpm}}{60} has units of s−1\text{s}^{-1} or rev/s\text{rev/s}; angular speed ω=2πf\omega = 2\pi f has units of rad/s\text{rad/s}.

  • Verify before multiplying by radius rr that your rotational rate is in rad/s\text{rad/s}, since v=ωrv = \omega r requires ω\omega to be in radians per unit time.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the given rotation rate to radians per second: ω=(1003revmin)(2π rad1 rev)(1 min60 s)=10π9 rad/s≈3.49 rad/s\omega = \left(\frac{100}{3}\frac{\text{rev}}{\text{min}}\right)\left(\frac{2\pi\text{ rad}}{1\text{ rev}}\right)\left(\frac{1\text{ min}}{60\text{ s}}\right) = \frac{10\pi}{9}\text{ rad/s} \approx 3.49\text{ rad/s}.

  2. Substitute ω=10π9 rad/s\omega = \frac{10\pi}{9}\text{ rad/s} into the linear speed formula for each track: vA=(10π9)(0.144 m)≈0.503 m/sv_A = \left(\frac{10\pi}{9}\right)(0.144\text{ m}) \approx 0.503\text{ m/s} and vB=(10π9)(0.0600 m)≈0.209 m/sv_B = \left(\frac{10\pi}{9}\right)(0.0600\text{ m}) \approx 0.209\text{ m/s}.

Final answer

(a) ω=3.49 rad/s\omega = 3.49\text{ rad/s}; (b) vA=0.503 m/sv_A = 0.503\text{ m/s}, vB=0.209 m/sv_B = 0.209\text{ m/s}; (c) vAvB=2.40\frac{v_A}{v_B} = 2.40

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting rotational quantities using dimensional analysis so that units cancel visibly.

  • Remember that the formula v=ωrv = \omega r strictly requires ω\omega in radians per second, never in revolutions per second or rpm.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the relationship between linear speed, angular speed, and radius by writing v = ω / r instead of v = ω r.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=1003×2π60=3.49 rad/s\omega = \frac{100}{3} \times \frac{2\pi}{60} = 3.49\text{ rad/s}

  2. Step 2

    rA=0.144 m,  rB=0.0600 m  ⟹  vA=ωrA=3.490.144=24.2 m/s  ⟹  vB=ωrB=3.490.0600=58.2 m/sr_A = 0.144\text{ m},\; r_B = 0.0600\text{ m} \implies v_A = \frac{\omega}{r_A} = \frac{3.49}{0.144} = 24.2\text{ m/s} \implies v_B = \frac{\omega}{r_B} = \frac{3.49}{0.0600} = 58.2\text{ m/s}

    Correct

    vA=ωrA=(3.49 rad/s)(0.144 m)≈0.503 m/s  ⟹  vB=ωrB=(3.49 rad/s)(0.0600 m)≈0.209 m/sv_A = \omega r_A = (3.49\text{ rad/s})(0.144\text{ m}) \approx 0.503\text{ m/s} \implies v_B = \omega r_B = (3.49\text{ rad/s})(0.0600\text{ m}) \approx 0.209\text{ m/s}

    Linear speed is directly proportional to radius (v=ωrv = \omega r), not inversely proportional (v=ωrv = \frac{\omega}{r}). A point farther from the center covers a greater distance in each revolution, so it must travel at a higher linear speed.

  3. Step 3

    vAvB=24.258.2=0.416\frac{v_A}{v_B} = \frac{24.2}{58.2} = 0.416

    Correct

    vAvB=rArB=14.4 cm6.00 cm=2.40\frac{v_A}{v_B} = \frac{r_A}{r_B} = \frac{14.4\text{ cm}}{6.00\text{ cm}} = 2.40

    Your division followed logically from your calculated values of vAv_A and vBv_B, but because both speeds were inverted, your final ratio is the reciprocal of the true ratio.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the mixed fraction 3313 rpm33\frac{1}{3}\text{ rpm} to 1003 rpm\frac{100}{3}\text{ rpm}.

You used the correct conversion factors between revolutions and radians, and between minutes and seconds, to find ω=3.49 rad/s\omega = 3.49\text{ rad/s}.

You correctly converted both track radii from centimeters to meters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Linear-Angular Speed Formula

You divided angular speed by radius instead of multiplying them together.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated linear speed as inversely related to radial distance rather than directly proportional. In circular motion, arc length is s=rθs = r\theta, which differentiates with respect to time to give tangential speed v=ωrv = \omega r. As radius increases on a rigid rotating body, linear speed must increase proportionally.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis
  • Angular speed has units of rad/s\text{rad/s} (or s−1\text{s}^{-1}), and radius has units of m\text{m}. Linear speed must have units of m/s\text{m/s}.

  • Multiply ω\omega by rr: (s−1)⋅(m)=m/s(\text{s}^{-1}) \cdot (\text{m}) = \text{m/s}. Dividing ωr\frac{\omega}{r} yields s−1m=1m⋅s\frac{\text{s}^{-1}}{\text{m}} = \frac{1}{\text{m}\cdot\text{s}}, which does not match speed units.

Physical Reality Check
  • Every point on a rigid disk completes one full rotation in the same period TT.

  • Since outer tracks have a larger circumference (2πr2\pi r) to cover in the exact same time period TT, points farther from the axis must move faster, meaning vv must increase as rr increases.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the correct formula connecting linear and angular speed: v=ωrv = \omega r.

  2. Compute Track A: vA=(10π9 rad/s)(0.144 m)≈0.503 m/sv_A = \left(\frac{10\pi}{9}\text{ rad/s}\right)(0.144\text{ m}) \approx 0.503\text{ m/s}.

  3. Compute Track B: vB=(10π9 rad/s)(0.0600 m)≈0.209 m/sv_B = \left(\frac{10\pi}{9}\text{ rad/s}\right)(0.0600\text{ m}) \approx 0.209\text{ m/s}.

  4. Compute the ratio: vAvB=ωrAωrB=rArB=14.4 cm6.00 cm=2.40\frac{v_A}{v_B} = \frac{\omega r_A}{\omega r_B} = \frac{r_A}{r_B} = \frac{14.4\text{ cm}}{6.00\text{ cm}} = 2.40.

Final answer

(a) ω=3.49 rad/s\omega = 3.49\text{ rad/s}; (b) vA=0.503 m/sv_A = 0.503\text{ m/s}, vB=0.209 m/sv_B = 0.209\text{ m/s}; (c) vAvB=2.40\frac{v_A}{v_B} = 2.40

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the rotational-linear bridge formulas: displacement s=rθs = r\theta, tangential speed v=ωrv = \omega r, and tangential acceleration at=αra_t = \alpha r. Notice that every linear quantity is obtained by multiplying the angular quantity by radius.

  • Always perform a quick units check: (rad/s)×m=m/s(\text{rad/s}) \times \text{m} = \text{m/s}.

  • Complete the follow-up practice drills to solidify when to multiply versus divide by radius.

OverviewACEpath Teacher's Diagnosis

03 The student adopts the misconception mentioned in the problem that points on a rigid body must share the same linear speed, equating both speeds to the outer rim's linear speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=1003×2π60=3.49 rad/s\omega = \frac{100}{3} \times \frac{2\pi}{60} = 3.49\text{ rad/s}

  2. Step 2

    rA=0.144 m  ⟹  vA=ωrA=(3.49)(0.144)=0.503 m/sr_A = 0.144\text{ m} \implies v_A = \omega r_A = (3.49)(0.144) = 0.503\text{ m/s}

  3. Step 3

    vB=vA=0.503 m/sv_B = v_A = 0.503\text{ m/s}

    Correct

    vB=ωrB=(3.49 rad/s)(0.0600 m)≈0.209 m/sv_B = \omega r_B = (3.49\text{ rad/s})(0.0600\text{ m}) \approx 0.209\text{ m/s}

    You set vBv_B equal to vAv_A, assuming linear speed is constant across the record. On a rigid rotating body, angular speed ω\omega is uniform, but linear speed depends on radius: vB=ωrBv_B = \omega r_B.

  4. Step 4

    vAvB=0.5030.503=1.00\frac{v_A}{v_B} = \frac{0.503}{0.503} = 1.00

    Correct

    vAvB=rArB=14.4 cm6.00 cm=2.40\frac{v_A}{v_B} = \frac{r_A}{r_B} = \frac{14.4\text{ cm}}{6.00\text{ cm}} = 2.40

    Your ratio calculation followed logically from your value of vBv_B, but it is incorrect because of the error in Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately converted the angular speed from revolutions per minute to radians per second.

You correctly converted the radius from centimeters to meters for Track A.

You correctly used the formula v=ωrv = \omega r to compute the linear speed of Track A.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Equating linear speed instead of angular speed on a rigid rotating body

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated angular speed (which is identical for all points on a rotating rigid body) with linear speed (which increases proportionally with distance from the rotation axis).

REASONING PATH
Your ACEpath teacher’s suggested approach
Rigid Body Kinematics Rule
  • Every point on a rotating rigid body sweeps out the same angle in the same time (same ω\omega), but points farther out travel along larger circular paths in that same time (v=ωrv = \omega r).

  • Always substitute the specific radius rr for each point when calculating linear speed v=ωrv = \omega r.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the radius of Track B to meters: rB=6.00 cm=0.0600 mr_B = 6.00\text{ cm} = 0.0600\text{ m}.

  2. Calculate vBv_B using Track B's radius: vB=ωrB=(3.49 rad/s)(0.0600 m)≈0.209 m/sv_B = \omega r_B = (3.49\text{ rad/s})(0.0600\text{ m}) \approx 0.209\text{ m/s}.

  3. Calculate the speed ratio: vAvB=0.503 m/s0.209 m/s=14.4 cm6.00 cm=2.40\frac{v_A}{v_B} = \frac{0.503\text{ m/s}}{0.209\text{ m/s}} = \frac{14.4\text{ cm}}{6.00\text{ cm}} = 2.40.

Final answer

(a) ω=3.49 rad/s\omega = 3.49\text{ rad/s}; (b) vA=0.503 m/sv_A = 0.503\text{ m/s}, vB=0.209 m/sv_B = 0.209\text{ m/s}; (c) vAvB=2.40\frac{v_A}{v_B} = 2.40

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between rotational quantities (θ\theta, ω\omega, α\alpha) which are shared across a rigid body, and translational quantities (ss, vv, ata_t) which scale with radius rr.

  • Practice computing tangential velocities for concentric points on rotating disks and wheels.

Lock it in

Similar question

01

A compact disc spins at 500 rpm500\text{ rpm}. (a) Calculate its angular speed ω\omega in rad/s\text{rad/s}. (b) Determine the linear speed of a data track located at radius r=4.0 cmr = 4.0\text{ cm}.

Answer

(a) ω=500×2π60=50π3≈52.4 rad/s\omega = 500 \times \frac{2\pi}{60} = \frac{50\pi}{3} \approx 52.4\text{ rad/s}. (b) v=ωr=(50π3)(0.040 m)≈2.09 m/sv = \omega r = \left(\frac{50\pi}{3}\right)(0.040\text{ m}) \approx 2.09\text{ m/s}.

02

A hard drive platter of radius 4.50 cm4.50\text{ cm} rotates at 7200 rpm7200\text{ rpm}. Find the linear speed of a magnetic head reading data at the outer rim (r=4.50 cmr = 4.50\text{ cm}) and at an inner track (r=1.80 cmr = 1.80\text{ cm}).

Answer

First find ω=7200×2π60=240π≈754 rad/s\omega = 7200 \times \frac{2\pi}{60} = 240\pi \approx 754\text{ rad/s}. At the outer rim, vouter=(240π)(0.0450 m)≈33.9 m/sv_{\text{outer}} = (240\pi)(0.0450\text{ m}) \approx 33.9\text{ m/s}. At the inner track, vinner=(240π)(0.0180 m)≈13.6 m/sv_{\text{inner}} = (240\pi)(0.0180\text{ m}) \approx 13.6\text{ m/s}.

03

Two gears, Gear 1 with radius R1=12.0 cmR_1 = 12.0\text{ cm} and Gear 2 with radius R2=4.00 cmR_2 = 4.00\text{ cm}, are meshed together with their teeth interlocking so that their rims move without slipping. If Gear 1 turns at 45.0 rpm45.0\text{ rpm}, determine: (a) the linear contact speed vv at the mesh point, and (b) the rotation rate of Gear 2 in rpm\text{rpm}.

Answer

(a) For Gear 1, ω1=45.0×2π60=1.50π rad/s≈4.71 rad/s\omega_1 = 45.0 \times \frac{2\pi}{60} = 1.50\pi\text{ rad/s} \approx 4.71\text{ rad/s}, giving rim speed v=ω1R1=(1.50π)(0.120 m)=0.180π≈0.565 m/sv = \omega_1 R_1 = (1.50\pi)(0.120\text{ m}) = 0.180\pi \approx 0.565\text{ m/s}. (b) Since linear rim speeds match (v=ω2R2v = \omega_2 R_2), ω2=0.180π0.0400=4.50π rad/s\omega_2 = \frac{0.180\pi}{0.0400} = 4.50\pi\text{ rad/s}, which corresponds to 45.0×12.04.00=135 rpm45.0 \times \frac{12.0}{4.00} = 135\text{ rpm}.

Loading workspace…