Resources
In fluid mechanics, the onset of turbulent flow past an obstacle depends on the dimensionless Reynolds number , where is fluid density, is flow speed, is a characteristic length, and is dynamic viscosity. Show that is strictly dimensionless by substituting the SI base units for each constituent variable, and compute the value of for water at (, ) flowing at past a cylinder of diameter to evaluate if it exceeds the laminar boundary threshold of .
Answer and steps
Final answer
The SI unit expression evaluates to (dimensionless); , which exceeds the laminar threshold of .
Steps
Express Dynamic Viscosity in SI Base Units
The formula for the Reynolds number is:
To verify its dimensions, express all quantities in the fundamental SI base units (, , and ):
- Density :
- Flow speed :
- Characteristic length :
The unit of dynamic viscosity is the pascal-second (). Recall that pressure is force per unit area (), and force is mass times acceleration ():
Multiplying by seconds gives the SI base units of :
Show That is Dimensionless
Substitute the base units into the numerator :
Now divide the numerator units by the denominator units:
All base units cancel out entirely, proving that is strictly dimensionless.
Calculate the Reynolds Number and Compare with the Threshold
Substitute the given values into the Reynolds number equation:
Multiply the terms in the numerator:
Divide by :
Comparing this with the laminar boundary threshold:
The calculated value of significantly exceeds the laminar threshold of .
Typical errors
01 A student inverts the power of ten in the denominator when dividing by 1.00 × 10⁻³, multiplying by 10⁻³ instead of dividing, which yields an erroneously small Reynolds number.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You evaluated as . Dividing by is mathematically equivalent to multiplying by , giving .
- Step 4Correct
Your comparison followed logically from your calculated value of , but because the calculated value was incorrect, the final comparison and conclusion were reversed.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly derived the SI base units of dynamic viscosity from the definition of the pascal.
You successfully proved that the Reynolds number has no units by cancelling all constituent base units.
You accurately substituted all physical parameters into the formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally treated dividing by as multiplying by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisapplication of negative power laws when simplifying denominators in scientific notation, confusing with .
REASONING PATH
Your ACEpath teacher’s suggested approach- Reciprocal of Negative Powers
Dividing by a power with a negative exponent flips the sign of the exponent: .
Move the denominator power to the numerator and change the sign of its exponent before multiplying.
CORRECTED PATH
ACEpath Teacher's DemonstrationEvaluate the numerator: .
Apply the power rule to the denominator: .
Compare the value to the threshold: , which exceeds the laminar threshold.
; it exceeds the laminar threshold of .
02 A student incorrectly derives the base units of dynamic viscosity by omitting the second in Pa·s, concluding that the units do not cancel to 1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly reduced the pascal () to base units , but dynamic viscosity has units of pascal-seconds (), not pascals (). You need to multiply by seconds to find the base units of .
- Step 2Correct
Because of the omitted second in the unit for viscosity, your denominator was missing a factor of , which caused the time units not to cancel out.
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly derived the SI base units of the pascal from first principles as .
You set up the correct dimensional ratio using density, speed, and length in the numerator.
You computed the numerical value of accurately and drew the correct physical conclusion regarding the flow threshold.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the unit of dynamic viscosity directly to pressure () instead of pressure-time ().
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing pressure with dynamic viscosity by dropping the time dimension () in derived compound units, which prevents complete unit cancellation in dimensionless groups.
REASONING PATH
Your ACEpath teacher’s suggested approach- Compound Derived Units
Dynamic viscosity is measured in pascal-seconds: .
Always write down the full compound unit given in the problem statement before decomposing it into base units.
- Dimensionless Quantity Verification
A dimensionless number must have all base unit powers equal to zero ().
If a known dimensionless group evaluates with leftover units such as seconds, re-check each variable's base unit derivation for a dropped or extra unit factor.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the full SI unit of dynamic viscosity: .
Evaluate the numerator's units: .
Divide numerator units by denominator units: (dimensionless).
The SI base units cancel completely to (dimensionless), and , which exceeds the laminar threshold.
03 A student confuses dynamic viscosity with kinematic viscosity and inadvertently omits the density term ρ from the numerator calculation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the density term from the numerator. The formula requires the kinematic viscosity , whereas the given quantity was dynamic viscosity , requiring .
- Step 3Correct
Because was omitted in the previous step, your calculated value of was off by a factor of , leading you to conclude that the flow does not exceed the threshold.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly broke down the derived unit into fundamental SI base units.
You clearly demonstrated that the Reynolds number expression is strictly dimensionless.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally dropped fluid density when writing the Reynolds number formula for the numerical calculation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou likely confused the two standard formulations of the Reynolds number: (which uses dynamic viscosity ) and (which uses kinematic viscosity ). Since the problem supplied dynamic viscosity , the factor of must remain in the numerator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match Viscosity Type to the Formula
Dynamic viscosity has units (or ) and requires . Kinematic viscosity has units and requires .
Always verify whether the given viscosity is dynamic () or kinematic () before choosing which Reynolds number form to evaluate.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the fluid density in the numerator: .
Evaluate the numerator: .
Divide by : .
Compare with the threshold: , which confirms that the flow exceeds the laminar threshold.
, which exceeds the laminar threshold of .
Lock it in
What is the equivalent algebraic rule for moving a power of ten from the denominator to the numerator, ?
. Moving a base across the fraction bar inverts the sign of its exponent.
Similar question
A capillary blood vessel has blood flowing through it with density , average speed , vessel diameter , and dynamic viscosity . Compute the Reynolds number .
Answer
. Key steps: Numerator is . Dividing by : .
Air at has density and dynamic viscosity . It flows at over a model airplane wing with chord length . Compute the Reynolds number and determine whether flow is laminar (threshold ).
Answer
, which is laminar. Key steps: Numerator . Then . Since , the boundary layer remains laminar.
An oil pipe of diameter carries crude oil (, kinematic viscosity ) at an average speed of . First show that kinematic viscosity has SI base units of , then calculate .
Answer
Unit verification: . Numerical value: . Key steps: Numerator . Dividing by : .