Resources

A laboratory group investigates Hooke's law for a vertically hanging coil spring. Instead of recording the total elongated length, the group tabulates the applied tensile force F (N)F\text{ (N)} and the corresponding elastic potential energy Us (mJ)U_s\text{ (mJ)} stored in the spring, which was computed from the area under their experimental force-displacement graph:

Applied Force F (N)F\text{ (N)}Stored Energy Us (mJ)U_s\text{ (mJ)}
2.02.016.016.0
4.04.064.064.0
6.06.0144.0144.0
8.08.0256.0256.0

Using the theoretical relation Us=F22kU_s = \frac{F^2}{2k}, construct a linear relationship to determine the effective spring constant kk in N/m\text{N/m}, and calculate the spring's physical elongation Δx\Delta x in centimeters when an applied force of F=5.0 NF = 5.0\text{ N} is maintained in static equilibrium.

Answer and steps

Final answer

k=125 N/mk = 125\text{ N/m}; Δx=4.0 cm\Delta x = 4.0\text{ cm}

Steps

01

Linearize the Theoretical Model

The elastic potential energy stored in an ideal Hookean spring in terms of the applied tensile force FF is given by: Us=F22k=(12k)F2U_s = \frac{F^2}{2k} = \left(\frac{1}{2k}\right) F^2

To linearize this relationship in the form y=mx+cy = m x + c:

  • Plot UsU_s (in joules, J\text{J}) on the vertical axis (yy).
  • Plot F2F^2 (in N2\text{N}^2) on the horizontal axis (xx).
  • The graph has a theoretical yy-intercept of c=0c = 0 and a slope of: m=12km = \frac{1}{2k}

02

Tabulate F2F^2 and Convert Units of Energy

Convert the stored energy from millijoules (mJ\text{mJ}) to standard SI units of joules (J\text{J}), where 1 mJ=10−3 J1\text{ mJ} = 10^{-3}\text{ J}:

Applied Force F (N)F\text{ (N)}F2 (N2)F^2\text{ (N}^2\text{)}Us (mJ)U_s\text{ (mJ)}Us (J)U_s\text{ (J)}
2.02.04.04.016.016.00.0160.016
4.04.016.016.064.064.00.0640.064
6.06.036.036.0144.0144.00.1440.144
8.08.064.064.0256.0256.00.2560.256

03

Calculate the Spring Constant kk

Using any pair of data points (or calculating the constant ratio UsF2\frac{U_s}{F^2} across the entire dataset), determine the slope mm: m=ΔUsΔ(F2)=0.064 J−0.016 J16.0 N2−4.0 N2=0.04812.0=0.004 J/N2m = \frac{\Delta U_s}{\Delta (F^2)} = \frac{0.064\text{ J} - 0.016\text{ J}}{16.0\text{ N}^2 - 4.0\text{ N}^2} = \frac{0.048}{12.0} = 0.004\text{ J/N}^2

Equate this slope to the theoretical expression 12k\frac{1}{2k}: 12k=0.004 m/N\frac{1}{2k} = 0.004\text{ m/N}

2k=10.004=250 N/m  ⟹  k=125 N/m2k = \frac{1}{0.004} = 250\text{ N/m} \implies k = 125\text{ N/m}

Common Pitfall: Forgetting to convert millijoules (mJ\text{mJ}) to joules (J\text{J}) results in an answer off by a factor of 10001000 (k=0.125 N/mk = 0.125\text{ N/m}). Additionally, do not omit the factor of 22 in the denominator of 12k\frac{1}{2k}.


04

Determine the Elongation Δx\Delta x

By Hooke's law, the restoring force equals the applied force in static equilibrium: F=kΔxF = k \Delta x

Solve for the physical elongation Δx\Delta x when F=5.0 NF = 5.0\text{ N}: Δx=Fk=5.0 N125 N/m=0.040 m\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m}

Convert meters to centimeters (1 m=100 cm1\text{ m} = 100\text{ cm}): Δx=0.040×100 cm=4.0 cm\Delta x = 0.040 \times 100\text{ cm} = 4.0\text{ cm}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the stored potential energy from millijoules to joules, resulting in a spring constant that is 1000 times too small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Us=12k⋅F2  ⟹  slope m=UsF2=4.0U_s = \frac{1}{2k} \cdot F^2 \implies \text{slope } m = \frac{U_s}{F^2} = 4.0

    Correct

    m=UsF2=16.0×10−3 J(2.0 N)2=0.004 J/N2m = \frac{U_s}{F^2} = \frac{16.0 \times 10^{-3}\text{ J}}{(2.0\text{ N})^2} = 0.004\text{ J/N}^2

    You correctly recognized that plotting UsU_s against F2F^2 yields a line with slope m=12km = \frac{1}{2k}, but you substituted Us=16.0U_s = 16.0 directly from the table without converting millijoules (mJ\text{mJ}) to standard joules (J\text{J}).

  2. Step 2

    k=12m=12⋅4.0=0.125 N/mk = \frac{1}{2m} = \frac{1}{2 \cdot 4.0} = 0.125\text{ N/m}

    Correct

    k=12m=12(0.004 J/N2)=125 N/mk = \frac{1}{2m} = \frac{1}{2(0.004\text{ J/N}^2)} = 125\text{ N/m}

    Your formula k=12mk = \frac{1}{2m} is correct, but your calculated value of kk is off by a factor of 10001000 due to the unconverted slope from Step 1.

  3. Step 3

    Δx=Fk=5.00.125=40 m=4000 cm\Delta x = \frac{F}{k} = \frac{5.0}{0.125} = 40\text{ m} = 4000\text{ cm}

    Correct

    Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}

    Your application of Hooke's law Δx=Fk\Delta x = \frac{F}{k} and your conversion from meters to centimeters were carried out correctly, but the result was distorted by the incorrect spring constant.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly linearized the potential energy formula into the form Us=(12k)F2U_s = \left(\frac{1}{2k}\right)F^2.

You correctly related the slope mm to the spring constant via k=12mk = \frac{1}{2m}.

You correctly applied Hooke's law Δx=Fk\Delta x = \frac{F}{k} to find the elongation and converted meters to centimeters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Metric Prefix Conversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You read the numerical values from the table header without accounting for the metric prefix 'm' (milli-) attached to the energy units, leading you to treat millijoules as base SI joules.

REASONING PATH
Your ACEpath teacher’s suggested approach
Inspect Table Header Units
  • Before substituting tabular values into physical formulas, express all quantities in base SI units.

  • Check for prefixes like mJ\text{mJ}, cm\text{cm}, or kN\text{kN}, and rewrite the values with their power-of-ten multipliers (1 mJ=10−3 J1\text{ mJ} = 10^{-3}\text{ J}).

Physical Sanity Check
  • Laboratory coil springs typically stretch by centimeters, not tens of meters, under modest forces.

  • Pause when an elongation reaches 40 m40\text{ m} for a 5.0 N5.0\text{ N} pull; an absurdly large displacement immediately signals an underestimated spring constant.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the stored energy to base SI units: Us=16.0 mJ=0.016 JU_s = 16.0\text{ mJ} = 0.016\text{ J}.

  2. Compute the slope: m=UsF2=0.016 J(2.0 N)2=0.004 J/N2m = \frac{U_s}{F^2} = \frac{0.016\text{ J}}{(2.0\text{ N})^2} = 0.004\text{ J/N}^2.

  3. Calculate the spring constant: k=12m=12(0.004 J/N2)=125 N/mk = \frac{1}{2m} = \frac{1}{2(0.004\text{ J/N}^2)} = 125\text{ N/m}.

  4. Calculate the physical elongation: Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}.

Final answer

k=125 N/mk = 125\text{ N/m}; Δx=4.0 cm\Delta x = 4.0\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always circle the unit in table column headers before beginning calculations.

  • Perform order-of-magnitude sense checks on final physical dimensions (e.g., spring elongation).

OverviewACEpath Teacher's Diagnosis

02 The student misidentifies the slope of Us versus F² as 1/k rather than 1/(2k), omitting the factor of 2 and obtaining twice the correct spring constant.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Us=0.0160 J at F2=4.0 N2  ⟹  slope m=0.01604.0=0.0040U_s = 0.0160\text{ J}\text{ at } F^2 = 4.0\text{ N}^2 \implies \text{slope } m = \frac{0.0160}{4.0} = 0.0040

  2. Step 2

    k=1m=10.0040=250 N/mk = \frac{1}{m} = \frac{1}{0.0040} = 250\text{ N/m}

    Correct

    m=12k  ⟹  k=12m=12(0.0040)=125 N/mm = \frac{1}{2k} \implies k = \frac{1}{2m} = \frac{1}{2(0.0040)} = 125\text{ N/m}

    From the formula Us=(12k)F2U_s = \left(\frac{1}{2k}\right)F^2, the slope represents 12k\frac{1}{2k}, not 1k\frac{1}{k}. Forgetting the factor of 22 in the denominator doubled your spring constant.

  3. Step 3

    Δx=Fk=5.0250=0.020 m=2.0 cm\Delta x = \frac{F}{k} = \frac{5.0}{250} = 0.020\text{ m} = 2.0\text{ cm}

    Correct

    Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}

    Your method and unit conversions using Hooke's law were completely correct, but the numerical answer was halved due to your propagated spring constant from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted energy from millijoules to joules before calculating the slope.

You correctly identified that plotting UsU_s against F2F^2 yields a linear relationship through the origin.

You applied Hooke's law Δx=Fk\Delta x = \frac{F}{k} and converted meters to centimeters properly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Constant Factor in Linearized Slope

You set the slope equal to 1k\frac{1}{k} rather than matching the coefficient 12k\frac{1}{2k} from the energy equation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking constant numerical coefficients when mapping a theoretical physics equation onto the standard linear form y=mx+cy = m x + c.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Linear Form Explicitly
  • Write y=(slope)⋅xy = (\text{slope}) \cdot x side-by-side with the physical equation to isolate the entire coefficient.

  • Rewrite Us=F22kU_s = \frac{F^2}{2k} as Us=(12k)F2U_s = \left(\frac{1}{2k}\right) F^2, identifying y=Usy = U_s, x=F2x = F^2, and m=12km = \frac{1}{2k}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the experimental slope equal to the full theoretical coefficient: m=12k=0.0040 J/N2m = \frac{1}{2k} = 0.0040\text{ J/N}^2.

  2. Solve for the spring constant: k=12(0.0040)=125 N/mk = \frac{1}{2(0.0040)} = 125\text{ N/m}.

  3. Substitute k=125 N/mk = 125\text{ N/m} into Hooke's law: Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}.

Final answer

k=125 N/mk = 125\text{ N/m}; Δx=4.0 cm\Delta x = 4.0\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always isolate the grouped constant factor by writing the dependent variable as (constants)×(independent variable)(\text{constants}) \times (\text{independent variable}).

  • Perform a quick sanity check using the original definition Us=12k(Δx)2U_s = \frac{1}{2} k (\Delta x)^2 to verify that your calculated kk and Δx\Delta x yield the tabulated energy.

OverviewACEpath Teacher's Diagnosis

03 The student attempts to linearize Us with respect to F directly instead of F², dividing Us by F rather than F² and yielding an inconsistent, incorrect spring constant.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m=UsF=0.01602.0=0.0080m = \frac{U_s}{F} = \frac{0.0160}{2.0} = 0.0080

    Correct

    m=UsF2=0.0160 J(2.0 N)2=0.0040 J/N2m = \frac{U_s}{F^2} = \frac{0.0160\text{ J}}{(2.0\text{ N})^2} = 0.0040\text{ J/N}^2

    You correctly converted 16.0 mJ16.0\text{ mJ} to 0.0160 J0.0160\text{ J}, but the theoretical relationship is Us=(12k)F2U_s = \left(\frac{1}{2k}\right)F^2. To obtain a linear relation y=mxy = mx, the horizontal variable must be F2F^2, making the slope m=UsF2m = \frac{U_s}{F^2} rather than UsF\frac{U_s}{F}.

  2. Step 2

    k=12m=12⋅0.0080=62.5 N/mk = \frac{1}{2m} = \frac{1}{2 \cdot 0.0080} = 62.5\text{ N/m}

    Correct

    k=12m=12(0.0040 J/N2)=125 N/mk = \frac{1}{2m} = \frac{1}{2(0.0040\text{ J/N}^2)} = 125\text{ N/m}

    Your algebraic relation k=12mk = \frac{1}{2m} is correct, but substituting your earlier slope m=0.0080m = 0.0080 propagated the missing square error and yielded half the true spring constant.

  3. Step 3

    Δx=Fk=5.062.5=0.080 m=8.0 cm\Delta x = \frac{F}{k} = \frac{5.0}{62.5} = 0.080\text{ m} = 8.0\text{ cm}

    Correct

    Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}

    You correctly applied Hooke's law Δx=Fk\Delta x = \frac{F}{k} and converted meters to centimeters, but using k=62.5 N/mk = 62.5\text{ N/m} produced an elongation of 8.0 cm8.0\text{ cm} instead of 4.0 cm4.0\text{ cm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted millijoules to standard joules correctly (16.0 mJ=0.0160 J16.0\text{ mJ} = 0.0160\text{ J}).

You correctly related the slope of the linearized equation to the physical parameter using k=12mk = \frac{1}{2m}.

You correctly used Hooke's law Δx=Fk\Delta x = \frac{F}{k} and converted meters to centimeters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linearization variable mismatch

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You matched the energy expression Us=F22kU_s = \frac{F^2}{2k} to a linear slope using FF instead of identifying F2F^2 as the independent variable on the horizontal axis.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Non-Linear Equations to $y = mx + b$
  • For a model y=A⋅xny = A \cdot x^n, treat xnx^n as the single horizontal quantity XX so that the graph of yy versus XX is linear with slope m=Am = A.

  • Rewrite Us=(12k)F2U_s = \left(\frac{1}{2k}\right)F^2 in the standard form Y=mXY = mX, where Y=UsY = U_s and X=F2X = F^2, before taking the ratio or calculating slope.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute F2F^2 for the chosen point: F2=(2.0 N)2=4.0 N2F^2 = (2.0\text{ N})^2 = 4.0\text{ N}^2.

  2. Calculate the slope: m=UsF2=0.0160 J4.0 N2=0.0040 J/N2m = \frac{U_s}{F^2} = \frac{0.0160\text{ J}}{4.0\text{ N}^2} = 0.0040\text{ J/N}^2.

  3. Solve for kk: k=12m=12(0.0040)=125 N/mk = \frac{1}{2m} = \frac{1}{2(0.0040)} = 125\text{ N/m}.

  4. Determine elongation: Δx=Fk=5.0 N125 N/m=0.040 m=4.0 cm\Delta x = \frac{F}{k} = \frac{5.0\text{ N}}{125\text{ N/m}} = 0.040\text{ m} = 4.0\text{ cm}.

Final answer

k=125 N/mk = 125\text{ N/m}; Δx=4.0 cm\Delta x = 4.0\text{ cm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying the independent variable XX by writing power laws directly in Y=mX+cY = mX + c form before substituting numbers.

  • Double-check that your slope units match the axes: here, mm has units of J/N2=m/N\text{J}/\text{N}^2 = \text{m}/\text{N}, whereas UsF\frac{U_s}{F} has units of meters.

Lock it in

Similar question

01

A student plots elastic potential energy UsU_s on the vertical axis against F2F^2 on the horizontal axis for a spring and obtains a best-fit slope of m=2.5×10−3 J/N2m = 2.5 \times 10^{-3}\text{ J/N}^2. Determine the spring constant kk.

Answer

k=200 N/mk = 200\text{ N/m}. Using m=12km = \frac{1}{2k}, we find k=12m=12(2.5×10−3)=10.005=200 N/mk = \frac{1}{2m} = \frac{1}{2(2.5 \times 10^{-3})} = \frac{1}{0.005} = 200\text{ N/m}.

02

An experiment measures the stored energy in a spring as Us=45 mJU_s = 45\text{ mJ} when a tensile force of F=3.0 NF = 3.0\text{ N} is applied. Assuming ideal Hookean behavior, find the spring constant kk in N/m\text{N/m} and the extension Δx\Delta x in centimeters.

Answer

k=100 N/mk = 100\text{ N/m}, Δx=3.0 cm\Delta x = 3.0\text{ cm}. Convert Us=45×10−3 JU_s = 45 \times 10^{-3}\text{ J}. Then k=F22Us=3.022(0.045)=9.00.090=100 N/mk = \frac{F^2}{2U_s} = \frac{3.0^2}{2(0.045)} = \frac{9.0}{0.090} = 100\text{ N/m}. The extension is Δx=Fk=3.0100=0.030 m=3.0 cm\Delta x = \frac{F}{k} = \frac{3.0}{100} = 0.030\text{ m} = 3.0\text{ cm}.

03

A data table records the elongation of a spring in millimeters Δx (mm)\Delta x\text{ (mm)} and restoring force F (N)F\text{ (N)}. A linear plot of FF versus Δx\Delta x yields a slope of 0.25 N/mm0.25\text{ N/mm}. Express the spring constant kk in standard SI units (N/m\text{N/m}) and calculate the energy stored when stretched by 2.0 cm2.0\text{ cm}.

Answer

k=250 N/mk = 250\text{ N/m}, Us=0.050 JU_s = 0.050\text{ J} (or 50 mJ50\text{ mJ}). Since 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}, k=0.25 N/(10−3 m)=250 N/mk = 0.25\text{ N/(10}^{-3}\text{ m)} = 250\text{ N/m}. Then Us=12k(Δx)2=12(250)(0.020)2=0.050 JU_s = \frac{1}{2}k(\Delta x)^2 = \frac{1}{2}(250)(0.020)^2 = 0.050\text{ J}.

Loading workspace…