Resources

A solid rectangular brass plate of dimensions L0=30.00 cmL_0 = 30.00\text{ cm} by W0=20.00 cmW_0 = 20.00\text{ cm} at T0=20.0∘CT_0 = 20.0^\circ\text{C} has a circular hole of diameter d0=6.000 cmd_0 = 6.000\text{ cm} bored through its center. The linear thermal expansion coefficient of brass is α=1.90×10−5 ∘C−1\alpha = 1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1}. The entire plate is uniformly heated to Tf=180.0∘CT_f = 180.0^\circ\text{C}. (a) Address the common misconception that the hole shrinks because the metal expands inward into the void: determine whether the diameter of the hole increases, decreases, or remains constant upon heating. (b) Calculate the change in diameter Δd\Delta d of the circular hole and its final area Ahole,fA_{\text{hole}, f} at 180.0∘C180.0^\circ\text{C}.

Answer and steps

Final answer

(a) The hole expands outward (hole diameter increases, behaving exactly like a solid plug of brass of the same diameter); (b) Δd=+0.0182 cm=+0.182 mm\Delta d = +0.0182\text{ cm} = +0.182\text{ mm}; Ahole,f=28.45 cm2A_{\text{hole}, f} = 28.45\text{ cm}^2

Steps

01

Temperature Change

Part (a): Conceptual Analysis of Cavity Expansion

A common misconception is that when a solid body with a cavity or hole is heated, the surrounding material expands inward into the empty space, causing the hole to shrink. To see why this is incorrect, consider a "photographic enlargement" analogy:

  1. When an object is uniformly heated, the average distance between every pair of adjacent atoms in the material increases.
  2. Imagine cutting out the circular piece of brass (the "plug") that originally filled the hole. If both the plug and the plate are heated by the same temperature change ΔT\Delta T, the plug expands uniformly according to: Δdplug=d0αΔT\Delta d_{\text{plug}} = d_0 \alpha \Delta T
  3. Because the material properties and temperature change are uniform everywhere, the expanding plug would fit precisely back into the expanding hole at any temperature without any stress, gaps, or overlap.
  4. Therefore, any cavity or hole in a solid expands upon heating exactly as if it were filled with the surrounding material. The diameter of the hole increases.

Part (b): Quantitative Calculations

Calculate the change in temperature: ΔT=Tf−T0=180.0∘C−20.0∘C=160.0∘C\Delta T = T_f - T_0 = 180.0^\circ\text{C} - 20.0^\circ\text{C} = 160.0^\circ\text{C}

02

Change in Diameter (Δd\Delta d)

Using the formula for linear thermal expansion, treating the hole diameter like a solid line element of brass of length d0d_0: Δd=d0αΔT\Delta d = d_0 \alpha \Delta T Substitute the given values: Δd=(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=+0.01824 cm≈+0.0182 cm (or +0.182 mm)\Delta d = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = +0.01824\text{ cm} \approx +0.0182\text{ cm} \text{ (or } +0.182\text{ mm)}

03

Final Area of the Hole (Ahole,fA_{\text{hole}, f})

Calculate the new diameter dfd_f: df=d0+Δd=6.000 cm+0.01824 cm=6.01824 cmd_f = d_0 + \Delta d = 6.000\text{ cm} + 0.01824\text{ cm} = 6.01824\text{ cm}

Now compute the final area of the circular hole: Ahole,f=π4df2=π4(6.01824 cm)2≈28.45 cm2A_{\text{hole}, f} = \frac{\pi}{4} d_f^2 = \frac{\pi}{4} (6.01824\text{ cm})^2 \approx 28.45\text{ cm}^2

(Alternative check using area expansion coefficient β≈2α\beta \approx 2\alpha): A0=π4(6.000 cm)2≈28.274 cm2A_0 = \frac{\pi}{4}(6.000\text{ cm})^2 \approx 28.274\text{ cm}^2 Ahole,f≈A0(1+2αΔT)=28.274×(1+2(1.90×10−5)(160.0))≈28.45 cm2A_{\text{hole}, f} \approx A_0(1 + 2\alpha \Delta T) = 28.274 \times (1 + 2(1.90 \times 10^{-5})(160.0)) \approx 28.45\text{ cm}^2

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student believes the expanding metal pushes inward into the empty space, causing the hole diameter and area to decrease.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    As the brass plate expands, [...] into the open space. Therefore, the diameter of the hole decreases.

    Correct

    The hole diameter increases upon heating because thermal expansion scales every linear dimension of the object outward, behaving just as a solid plug of brass filling the hole would expand.

    You concluded that the hole shrinks as metal expands into the void. When an object is uniformly heated, the separation between every pair of atoms increases. A hole expands at the exact same rate as if it were filled with the same material.

  2. Step 2

    ΔT=180.0∘C−20.0∘C=160.0∘C\Delta T = 180.0^\circ\text{C} - 20.0^\circ\text{C} = 160.0^\circ\text{C}

  3. Step 3

    Δd=−d0αΔT=−(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=−0.01824 cm\Delta d = -d_0 \alpha \Delta T = -(6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = -0.01824\text{ cm}

    Correct

    Δd=d0αΔT=(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=+0.01824 cm\Delta d = d_0 \alpha \Delta T = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = +0.01824\text{ cm}

    You inserted a negative sign because of the assumption that the hole contracts. Because the hole expands, the change in diameter is positive: Δd=+0.0182 cm\Delta d = +0.0182\text{ cm} (or +0.182 mm+0.182\text{ mm}).

  4. Step 4

    df=6.000 cm−0.01824 cm=5.98176 cm  ⟹  Ahole,f=π(df2)2=π(2.99088 cm)2=28.10 cm2d_f = 6.000\text{ cm} - 0.01824\text{ cm} = 5.98176\text{ cm} \implies A_{\text{hole}, f} = \pi \left(\frac{d_f}{2}\right)^2 = \pi (2.99088\text{ cm})^2 = 28.10\text{ cm}^2

    Correct

    df=6.000 cm+0.01824 cm=6.01824 cm  ⟹  Ahole,f=π4df2≈28.45 cm2d_f = 6.000\text{ cm} + 0.01824\text{ cm} = 6.01824\text{ cm} \implies A_{\text{hole}, f} = \frac{\pi}{4}d_f^2 \approx 28.45\text{ cm}^2

    Your area calculation correctly used the circle area formula, but your result is smaller than the initial area due to the propagated negative sign from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the temperature difference ΔT=160.0∘C\Delta T = 160.0^\circ\text{C}.

You correctly applied the linear thermal expansion magnitude d0αΔTd_0 \alpha \Delta T.

You correctly applied the geometric area formula A=πr2A = \pi r^2 for a circle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error from conceptual cavity expansion misconception

No, this was not a simple arithmetic slip; you deliberately introduced a negative sign into the expansion formula based on the intuitive idea that material expands into empty space.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that material expands into adjacent empty space when heated. In isotropic thermal expansion, every interatomic distance increases by a factor of (1+αΔT)(1 + \alpha \Delta T). This acts as a uniform geometric scaling (photographic zoom), meaning all interior boundaries, cavities, and perimeters expand outward rather than inward.

REASONING PATH
Your ACEpath teacher’s suggested approach
Photographic Enlargement Principle
  • Uniform thermal expansion scales every linear dimension of an object by the factor (1+αΔT)(1 + \alpha \Delta T), including holes, gaps, and cavities.

  • Treat any cavity or hole as if it were filled with a solid plug of the surrounding material.

Sign of Linear Expansion
  • For a temperature increase (ΔT>0\Delta T > 0), ΔL=L0αΔT>0\Delta L = L_0 \alpha \Delta T > 0 for all dimensions.

  • Keep Δd\Delta d positive whenever ΔT>0\Delta T > 0, and add Δd\Delta d to d0d_0 to find the final diameter.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the positive linear thermal expansion formula: Δd=d0αΔT=(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=+0.01824 cm≈+0.0182 cm\Delta d = d_0 \alpha \Delta T = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = +0.01824\text{ cm} \approx +0.0182\text{ cm}.

  2. Find the final diameter: df=d0+Δd=6.000 cm+0.01824 cm=6.01824 cmd_f = d_0 + \Delta d = 6.000\text{ cm} + 0.01824\text{ cm} = 6.01824\text{ cm}.

  3. Calculate the final area of the circular hole: Ahole,f=π4df2=π4(6.01824 cm)2≈28.45 cm2A_{\text{hole}, f} = \frac{\pi}{4}d_f^2 = \frac{\pi}{4}(6.01824\text{ cm})^2 \approx 28.45\text{ cm}^2.

Final answer

(a) The hole diameter increases; (b) Δd=+0.0182 cm\Delta d = +0.0182\text{ cm} (+0.182 mm+0.182\text{ mm}), Ahole,f=28.45 cm2A_{\text{hole}, f} = 28.45\text{ cm}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember the 'plug analogy': imagine the cut-out piece of brass heated together with the plate; because it expands and must still fit flush, the hole must expand by the exact same amount.

  • Rework the final diameter and area using positive Δd\Delta d to verify Ahole,f>Ahole,0A_{\text{hole}, f} > A_{\text{hole}, 0}.

OverviewACEpath Teacher's Diagnosis

02 The student mistakenly uses the final temperature instead of the temperature change when calculating thermal expansion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Thermal expansion acts like a photographic enlargement, so all linear dimensions increase. Therefore, the diameter of the hole increases.

  2. Step 2

    Δd=d0αTf=(6.000 cm)(1.90×10−5 ∘C−1)(180.0∘C)=0.02052 cm\Delta d = d_0 \alpha T_f = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(180.0^\circ\text{C}) = 0.02052\text{ cm}

    Correct

    Δd=d0αΔT=(6.000 cm)(1.90×10−5 ∘C−1)(180.0∘C−20.0∘C)=0.01824 cm≈0.0182 cm\Delta d = d_0 \alpha \Delta T = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(180.0^\circ\text{C} - 20.0^\circ\text{C}) = 0.01824\text{ cm} \approx 0.0182\text{ cm}

    You substituted the final temperature Tf=180.0∘CT_f = 180.0^\circ\text{C} directly into the formula instead of the temperature change ΔT=Tf−T0=180.0∘C−20.0∘C=160.0∘C\Delta T = T_f - T_0 = 180.0^\circ\text{C} - 20.0^\circ\text{C} = 160.0^\circ\text{C}.

  3. Step 3

    df=6.000 cm+0.02052 cm=6.02052 cm  ⟹  Ahole,f=π(df2)2=π(3.01026 cm)2=28.47 cm2d_f = 6.000\text{ cm} + 0.02052\text{ cm} = 6.02052\text{ cm} \implies A_{\text{hole}, f} = \pi \left(\frac{d_f}{2}\right)^2 = \pi (3.01026\text{ cm})^2 = 28.47\text{ cm}^2

    Correct

    df=6.000 cm+0.01824 cm=6.01824 cm  ⟹  Ahole,f=π(6.01824 cm2)2≈28.45 cm2d_f = 6.000\text{ cm} + 0.01824\text{ cm} = 6.01824\text{ cm} \implies A_{\text{hole}, f} = \pi \left(\frac{6.01824\text{ cm}}{2}\right)^2 \approx 28.45\text{ cm}^2

    Your area formula and algebraic steps were carried out correctly, but the numerical answer is slightly off due to the earlier value of Δd\Delta d.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the photographic enlargement analogy to explain why the hole expands.

You selected the correct linear thermal expansion relation for a diameter and set up the area calculation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature change vs. absolute temperature confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the final temperature TfT_f as the change in temperature ΔT\Delta T, forgetting to subtract the initial temperature T0=20.0∘CT_0 = 20.0^\circ\text{C}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Temperature Interval Check
  • Thermal expansion depends on the difference between final and initial temperatures: ΔT=Tf−T0\Delta T = T_f - T_0.

  • Always write down ΔT=Tf−T0\Delta T = T_f - T_0 as an explicit preliminary step before plugging numbers into ΔL=L0αΔT\Delta L = L_0 \alpha \Delta T.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the temperature difference: ΔT=180.0∘C−20.0∘C=160.0∘C\Delta T = 180.0^\circ\text{C} - 20.0^\circ\text{C} = 160.0^\circ\text{C}.

  2. Find the change in diameter: Δd=d0αΔT=(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=0.01824 cm\Delta d = d_0 \alpha \Delta T = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = 0.01824\text{ cm}.

  3. Determine the final diameter: df=6.000 cm+0.01824 cm=6.01824 cmd_f = 6.000\text{ cm} + 0.01824\text{ cm} = 6.01824\text{ cm}.

  4. Calculate the final circular area: Ahole,f=π4df2=π4(6.01824 cm)2≈28.45 cm2A_{\text{hole}, f} = \frac{\pi}{4} d_f^2 = \frac{\pi}{4} (6.01824\text{ cm})^2 \approx 28.45\text{ cm}^2.

Final answer

Δd=+0.0182 cm\Delta d = +0.0182\text{ cm}, Ahole,f=28.45 cm2A_{\text{hole}, f} = 28.45\text{ cm}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Form the habit of explicitly computing and labeling ΔT=Tf−T0\Delta T = T_f - T_0 before substituting values into thermal equations.

  • Practice problems that specify nonzero initial temperatures to reinforce distinguishing between absolute temperature and temperature difference.

OverviewACEpath Teacher's Diagnosis

03 The student computes the change in area using the linear expansion coefficient α instead of the area expansion coefficient 2α (or forgets to square the expansion factor).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Every linear dimension expands uniformly outward as the plate is heated. Therefore, the diameter of the hole increases.

  2. Step 2

    ΔT=180.0∘C−20.0∘C=160.0∘C  ⟹  Δd=d0αΔT=(6.000 cm)(1.90×10−5 ∘C−1)(160.0∘C)=0.01824 cm\Delta T = 180.0^\circ\text{C} - 20.0^\circ\text{C} = 160.0^\circ\text{C} \implies \Delta d = d_0 \alpha \Delta T = (6.000\text{ cm})(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = 0.01824\text{ cm}

  3. Step 3

    A0=π(d02)2=π(3.000 cm)2=28.274 cm2A_0 = \pi \left(\frac{d_0}{2}\right)^2 = \pi (3.000\text{ cm})^2 = 28.274\text{ cm}^2

  4. Step 4

    ΔA=A0αΔT=(28.274 cm2)(1.90×10−5 ∘C−1)(160.0∘C)=0.086 cm2\Delta A = A_0 \alpha \Delta T = (28.274\text{ cm}^2)(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(160.0^\circ\text{C}) = 0.086\text{ cm}^2

    Correct

    ΔA=2αA0ΔT=2(1.90×10−5 ∘C−1)(28.274 cm2)(160.0∘C)≈0.172 cm2\Delta A = 2\alpha A_0 \Delta T = 2(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(28.274\text{ cm}^2)(160.0^\circ\text{C}) \approx 0.172\text{ cm}^2

    Area expands in two perpendicular dimensions, so the area expansion coefficient is β≈2α\beta \approx 2\alpha, not α\alpha alone.

  5. Step 5

    Ahole,f=A0+ΔA=28.274 cm2+0.086 cm2=28.36 cm2A_{\text{hole}, f} = A_0 + \Delta A = 28.274\text{ cm}^2 + 0.086\text{ cm}^2 = 28.36\text{ cm}^2

    Correct

    Ahole,f=A0+ΔA=28.274 cm2+0.172 cm2≈28.45 cm2A_{\text{hole}, f} = A_0 + \Delta A = 28.274\text{ cm}^2 + 0.172\text{ cm}^2 \approx 28.45\text{ cm}^2

    Your final area calculation correctly added ΔA\Delta A to A0A_0, but it inherited the underestimated ΔA\Delta A from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly explained why a hole in a heated plate expands outward rather than shrinking inward.

You accurately set up and evaluated the linear expansion Δd=d0αΔT\Delta d = d_0 \alpha \Delta T.

You computed the initial area A0A_0 of the circular hole with precise arithmetic.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear vs. area expansion coefficient confusion

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the one-dimensional expansion formula ΔA=A0αΔT\Delta A = A_0 \alpha \Delta T to a two-dimensional area, overlooking that area scales with length squared, which yields an area expansion coefficient of β≈2α\beta \approx 2\alpha.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimension Matching in Thermal Expansion
  • For an isotropic material with linear coefficient α\alpha, linear dimensions expand with α\alpha, areas expand with β≈2α\beta \approx 2\alpha, and volumes expand with γ≈3α\gamma \approx 3\alpha.

  • Always verify whether the quantity being expanded is a length, an area, or a volume, and multiply α\alpha by the dimension number (1, 2, or 3).

Alternative Direct Method for Final Area
  • Af=π4df2=π4(d0+Δd)2A_f = \frac{\pi}{4} d_f^2 = \frac{\pi}{4}(d_0 + \Delta d)^2

  • When you have already computed the new diameter df=d0+Δdd_f = d_0 + \Delta d, compute the final area directly from dfd_f to avoid coefficient confusion.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recognize that thermal area expansion satisfies ΔA=βA0ΔT≈2αA0ΔT\Delta A = \beta A_0 \Delta T \approx 2\alpha A_0 \Delta T.

  2. Substitute the given values: ΔA=2(1.90×10−5 ∘C−1)(28.274 cm2)(160.0∘C)≈0.1719 cm2\Delta A = 2(1.90 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(28.274\text{ cm}^2)(160.0^\circ\text{C}) \approx 0.1719\text{ cm}^2.

  3. Add the area change to the initial area: Ahole,f=28.274 cm2+0.1719 cm2≈28.45 cm2A_{\text{hole}, f} = 28.274\text{ cm}^2 + 0.1719\text{ cm}^2 \approx 28.45\text{ cm}^2.

Final answer

(a) The hole diameter increases; (b) Δd=+0.0182 cm\Delta d = +0.0182\text{ cm} (or +0.182 mm+0.182\text{ mm}), Ahole,f=28.45 cm2A_{\text{hole}, f} = 28.45\text{ cm}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric derivation showing why area expansion has coefficient 2α2\alpha by expanding (L0(1+αΔT))2(L_0(1+\alpha \Delta T))^2.

  • Practice computing final areas both via ΔA≈2αA0ΔT\Delta A \approx 2\alpha A_0 \Delta T and directly via Af=π4df2A_f = \frac{\pi}{4}d_f^2 to cross-check your work.

Lock it in

Similar question

01

A steel washer has an inner diameter of d1=2.000 cmd_1 = 2.000\text{ cm} and an outer diameter of d2=5.000 cmd_2 = 5.000\text{ cm} at 20.0∘C20.0^\circ\text{C}. The coefficient of linear expansion for steel is α=1.20×10−5 ∘C−1\alpha = 1.20 \times 10^{-5}\text{ }^\circ\text{C}^{-1}. If the washer is heated to 220.0∘C220.0^\circ\text{C}, find the change in the inner diameter Δd1\Delta d_1.

Answer

ΔT=200.0∘C\Delta T = 200.0^\circ\text{C}. The inner diameter expands outward just like a solid steel rod of length 2.000 cm2.000\text{ cm}: Δd1=d1αΔT=(2.000 cm)(1.20×10−5 ∘C−1)(200.0∘C)=+0.0048 cm=+0.048 mm\Delta d_1 = d_1 \alpha \Delta T = (2.000\text{ cm})(1.20 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(200.0^\circ\text{C}) = +0.0048\text{ cm} = +0.048\text{ mm}.

02

An aluminum ring with internal diameter 8.000 cm8.000\text{ cm} at 20.0∘C20.0^\circ\text{C} must be slipped over a steel shaft of diameter 8.012 cm8.012\text{ cm} (also at 20.0∘C20.0^\circ\text{C}). If only the aluminum ring is heated while the shaft stays at 20.0∘C20.0^\circ\text{C}, to what minimum temperature must the ring be heated? (For aluminum, α=2.40×10−5 ∘C−1\alpha = 2.40 \times 10^{-5}\text{ }^\circ\text{C}^{-1}.)

Answer

The ring's inner diameter must expand by Δd=8.012 cm−8.000 cm=0.012 cm\Delta d = 8.012\text{ cm} - 8.000\text{ cm} = 0.012\text{ cm}. Using Δd=d0αΔT\Delta d = d_0 \alpha \Delta T, ΔT=0.012 cm(8.000 cm)(2.40×10−5 ∘C−1)=62.5∘C\Delta T = \frac{0.012\text{ cm}}{(8.000\text{ cm})(2.40 \times 10^{-5}\text{ }^\circ\text{C}^{-1})} = 62.5^\circ\text{C}. Thus, Tf=T0+ΔT=20.0∘C+62.5∘C=82.5∘CT_f = T_0 + \Delta T = 20.0^\circ\text{C} + 62.5^\circ\text{C} = 82.5^\circ\text{C}.

03

A square copper plate of side length S0=10.00 cmS_0 = 10.00\text{ cm} has a square hole of side length s0=2.000 cms_0 = 2.000\text{ cm} cut out from its center at 0.0∘C0.0^\circ\text{C}. Take α=1.70×10−5 ∘C−1\alpha = 1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1}. When heated to 100.0∘C100.0^\circ\text{C}, calculate the percentage change in the area of the central square hole.

Answer

The hole side length scales as sf=s0(1+αΔT)s_f = s_0(1 + \alpha \Delta T). The hole area scales as Af=sf2=s02(1+αΔT)2≈A0(1+2αΔT)A_f = s_f^2 = s_0^2(1 + \alpha \Delta T)^2 \approx A_0(1 + 2\alpha \Delta T). The fractional area change is ΔAA0≈2αΔT=2(1.70×10−5 ∘C−1)(100.0∘C)=3.40×10−3=+0.34%\frac{\Delta A}{A_0} \approx 2\alpha \Delta T = 2(1.70 \times 10^{-5}\text{ }^\circ\text{C}^{-1})(100.0^\circ\text{C}) = 3.40 \times 10^{-3} = +0.34\%.

Loading workspace…