Resources

An electric winch lifts a crate of mass m=85.0 kgm = 85.0\text{ kg} vertically through a height of h=12.0 mh = 12.0\text{ m} at a constant speed in a time interval of t=15.0 st = 15.0\text{ s}. During this operation, the electric motor draws an average electrical power of Pin=920 WP_{\text{in}} = 920\text{ W}. Taking the acceleration due to gravity as g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the mechanical efficiency η\eta of the winch system as a percentage.

Answer and steps

Final answer

η=72.4%\eta = 72.4\%

Steps

01

Calculate the useful work done on the crate

To find the mechanical efficiency of the winch system, compare the useful power delivered to lift the crate with the total electrical power consumed.

Since the crate is lifted vertically at a constant speed, its kinetic energy remains constant (ΔK=0\Delta K = 0). The useful mechanical work output, WoutW_{\text{out}}, equals the increase in gravitational potential energy of the crate:

Wout=mghW_{\text{out}} = mgh

Substitute the given values: Wout=(85.0 kg)⋅(9.80 m/s2)⋅(12.0 m)=9996 JW_{\text{out}} = (85.0\text{ kg}) \cdot (9.80\text{ m/s}^2) \cdot (12.0\text{ m}) = 9996\text{ J}

02

Calculate the useful power output

The useful mechanical power output, PoutP_{\text{out}}, is the rate at which useful work is performed over the time interval tt:

Pout=WouttP_{\text{out}} = \frac{W_{\text{out}}}{t}

Pout=9996 J15.0 s=666.4 WP_{\text{out}} = \frac{9996\text{ J}}{15.0\text{ s}} = 666.4\text{ W}

03

Determine the mechanical efficiency

Mechanical efficiency, η\eta, is defined as the ratio of useful power output to total power input, expressed as a percentage:

η=PoutPin×100%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\%

Substitute Pout=666.4 WP_{\text{out}} = 666.4\text{ W} and Pin=920 WP_{\text{in}} = 920\text{ W}:

η=666.4 W920 W×100%≈72.435%\eta = \frac{666.4\text{ W}}{920\text{ W}} \times 100\% \approx 72.435\%

Rounding to three significant figures gives: η=72.4%\eta = 72.4\%

(Common Pitfall: Do not confuse input power with output power; because real systems lose energy to friction and electrical resistance, PoutP_{\text{out}} must always be less than PinP_{\text{in}}, yielding an efficiency less than 100%100\%.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates efficiency as the ratio of input power to output power instead of output power to input power, yielding an efficiency greater than 100%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Wout=mgh=85.0×9.80×12.0=9996 JW_{\text{out}} = mgh = 85.0 \times 9.80 \times 12.0 = 9996\text{ J}

  2. Step 2

    Pout=999615.0=666.4 WP_{\text{out}} = \frac{9996}{15.0} = 666.4\text{ W}

  3. Step 3

    η=PinPout×100%\eta = \frac{P_{\text{in}}}{P_{\text{out}}} \times 100\%

    Correct

    η=PoutPin×100%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\%

    Efficiency is defined as the ratio of useful output to total input, PoutPin×100%\frac{P_{\text{out}}}{P_{\text{in}}} \times 100\%, but you inverted the ratio to PinPout×100%\frac{P_{\text{in}}}{P_{\text{out}}} \times 100\%.

  4. Step 4

    η=(920666.4)×100%=138%\eta = \left(\frac{920}{666.4}\right) \times 100\% = 138\%

    Correct

    η=(666.4 W920 W)×100%≈72.4%\eta = \left(\frac{666.4\text{ W}}{920\text{ W}}\right) \times 100\% \approx 72.4\%

    This step evaluates correctly from your inverted formula in Step 3, but yields an unphysical efficiency greater than 100%100\%.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the useful gravitational work done on the crate using W=mghW = mgh.

You correctly determined the useful power output by dividing work by time.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted efficiency ratio

You set up the efficiency equation upside down as PinPout\frac{P_{\text{in}}}{P_{\text{out}}} instead of PoutPin\frac{P_{\text{out}}}{P_{\text{in}}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the numerator and denominator in the definition of efficiency. Efficiency measures what fraction of the supplied energy/power is converted into useful work, which means useful output must always be on top and total input on the bottom.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity check on efficiency values
  • For any passive or real-world machine, energy losses to friction or thermal dissipation ensure that Pout<PinP_{\text{out}} < P_{\text{in}}, so η<100%\eta < 100\%.

  • Whenever you calculate η>100%\eta > 100\%, immediately inspect your fraction to verify that output is in the numerator and input is in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the definition of efficiency: η=PoutPin×100%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\%.

  2. Substitute the calculated output power Pout=666.4 WP_{\text{out}} = 666.4\text{ W} and given input power Pin=920 WP_{\text{in}} = 920\text{ W}: η=666.4 W920 W×100%\eta = \frac{666.4\text{ W}}{920\text{ W}} \times 100\%.

  3. Evaluate and round to three significant figures: η≈72.4%\eta \approx 72.4\%.

Final answer

η=72.4%\eta = 72.4\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember the memory phrase: 'Efficiency = useful out over total in' (OutIn\frac{\text{Out}}{\text{In}}).

  • Always perform a quick reality check: can a real machine deliver more power than it consumes?

OverviewACEpath Teacher's Diagnosis

02 The student directly compares the work output in joules to the input power in watts without dividing the work by the time interval to obtain power output.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    W=mgh=85.0×9.80×12.0=9996 JW = mgh = 85.0 \times 9.80 \times 12.0 = 9996\text{ J}

  2. Step 2

    η=WPin×100%  ⟹  η=(9996920)×100%=1087%\eta = \frac{W}{P_{\text{in}}} \times 100\% \implies \eta = \left(\frac{9996}{920}\right) \times 100\% = 1087\%

    Correct

    Pout=Woutt=9996 J15.0 s=666.4 W  ⟹  η=PoutPin×100%=(666.4 W920 W)×100%≈72.4%P_{\text{out}} = \frac{W_{\text{out}}}{t} = \frac{9996\text{ J}}{15.0\text{ s}} = 666.4\text{ W} \implies \eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\% = \left(\frac{666.4\text{ W}}{920\text{ W}}\right) \times 100\% \approx 72.4\%

    You divided work (9996 J9996\text{ J}) directly by electrical power (920 W920\text{ W}). Because power is energy per unit time (1 W=1 J/s1\text{ W} = 1\text{ J/s}), dividing joules by watts yields seconds rather than a dimensionless efficiency ratio. You need to divide the useful work by the time elapsed (t=15.0 st = 15.0\text{ s}) to find the useful power output (Pout=666.4 WP_{\text{out}} = 666.4\text{ W}) before computing the ratio.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the useful work output equals the gravitational potential energy gained by the crate.

You substituted the given mass, gravitational acceleration, and height accurately to find W=9996 JW = 9996\text{ J}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimension Mismatch in Efficiency Formula

Dividing work in joules by power in watts without converting work into power output using the time interval.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating energy (work) with the rate of energy transfer (power), resulting in an expression comparing quantities with mismatched units and an efficiency greater than 100%100\%.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Consistency Check
  • Efficiency is a dimensionless ratio: η=PoutPin=EoutEin\eta = \frac{P_{\text{out}}}{P_{\text{in}}} = \frac{E_{\text{out}}}{E_{\text{in}}}.

  • Always verify that the numerator and denominator share the same units (watts over watts, or joules over joules).

Conservation of Energy Sanity Check
  • In any real macroscopic machine, useful energy output cannot exceed total energy input, meaning η≤100%\eta \le 100\%.

  • If your calculated efficiency exceeds 100%100\%, recheck whether you missed a time factor or inverted the input and output terms.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Pout=Woutt=9996 J15.0 s=666.4 WP_{\text{out}} = \frac{W_{\text{out}}}{t} = \frac{9996\text{ J}}{15.0\text{ s}} = 666.4\text{ W}

  2. η=PoutPin×100%=666.4 W920 W×100%≈72.435%\eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\% = \frac{666.4\text{ W}}{920\text{ W}} \times 100\% \approx 72.435\%

Final answer

η=72.4%\eta = 72.4\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Convert work (9996 J9996\text{ J}) into power output by dividing by time (15.0 s15.0\text{ s}) before comparing it to input power.

  • Perform a dimensional analysis check to confirm the efficiency ratio is dimensionless and strictly less than 100%100\%.

OverviewACEpath Teacher's Diagnosis

03 The student confuses mass with weight and omits the acceleration due to gravity g when calculating the work done to lift the crate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Wout=F×d=85.0×12.0=1020 JW_{\text{out}} = F \times d = 85.0 \times 12.0 = 1020\text{ J}

    Correct

    Wout=mgh=(85.0 kg)(9.80 m/s2)(12.0 m)=9996 JW_{\text{out}} = mgh = (85.0\text{ kg})(9.80\text{ m/s}^2)(12.0\text{ m}) = 9996\text{ J}

    You substituted the mass m=85.0 kgm = 85.0\text{ kg} as the force. To lift an object vertically at a constant speed, the applied force must balance its weight, F=mg=(85.0 kg)(9.80 m/s2)=833 NF = mg = (85.0\text{ kg})(9.80\text{ m/s}^2) = 833\text{ N}.

  2. Step 2

    Pout=102015.0=68.0 WP_{\text{out}} = \frac{1020}{15.0} = 68.0\text{ W}

    Correct

    Pout=Woutt=9996 J15.0 s=666.4 WP_{\text{out}} = \frac{W_{\text{out}}}{t} = \frac{9996\text{ J}}{15.0\text{ s}} = 666.4\text{ W}

    Your formula for power output P=WtP = \frac{W}{t} is correct, but the calculated value of 68.0 W68.0\text{ W} carries forward the incorrect work value from Step 1.

  3. Step 3

    η=(PoutPin)×100%\eta = \left(\frac{P_{\text{out}}}{P_{\text{in}}}\right) \times 100\%

  4. Step 4

    η=(68.0920)×100%=7.39%\eta = \left(\frac{68.0}{920}\right) \times 100\% = 7.39\%

    Correct

    η=(666.4 W920 W)×100%≈72.4%\eta = \left(\frac{666.4\text{ W}}{920\text{ W}}\right) \times 100\% \approx 72.4\%

    You evaluated the efficiency expression correctly using your previous numbers, but the result is inaccurate due to the omitted factor of gg in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that power is the rate of doing work (P=WtP = \frac{W}{t}).

You correctly applied the formula for mechanical efficiency ( η=PoutPin×100% \,\eta = \frac{P_{\text{out}}}{P_{\text{in}}} \times 100\%\,).

You performed the numerical division and percentage conversions accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Gravitational Acceleration

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated mass (mm, in kilograms) as the upward force (FF, in newtons), omitting the acceleration due to gravity (gg) needed to determine the weight of the object.

REASONING PATH
Your ACEpath teacher’s suggested approach
Mass vs. Weight
  • Mass (mm) measures the quantity of matter in kilograms, whereas weight (W=mgW = mg) is the gravitational force exerted on it in newtons.

  • Whenever an object is lifted vertically against gravity, remember that the required upward force is F=mgF = mg, not simply mm.

Sanity Check on Mechanical Efficiency
  • Commercial winches and electric motors typically have efficiencies between 50%50\% and 90%90\%.

  • If you calculate an unusually low efficiency (such as ≈7%\approx 7\%) for a simple motor lift, double-check whether a factor of g≈9.8 m/s2g \approx 9.8\text{ m/s}^2 was inadvertently left out.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the upward lifting force: F=mg=(85.0 kg)(9.80 m/s2)=833 NF = mg = (85.0\text{ kg})(9.80\text{ m/s}^2) = 833\text{ N}.

  2. Compute the work output: Wout=Fh=(833 N)(12.0 m)=9996 JW_{\text{out}} = Fh = (833\text{ N})(12.0\text{ m}) = 9996\text{ J}.

  3. Compute the power output: Pout=9996 J15.0 s=666.4 WP_{\text{out}} = \frac{9996\text{ J}}{15.0\text{ s}} = 666.4\text{ W}.

  4. Compute the efficiency: η=666.4 W920 W×100%≈72.4%\eta = \frac{666.4\text{ W}}{920\text{ W}} \times 100\% \approx 72.4\%.

Final answer

η=72.4%\eta = 72.4\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between mass (kg) and force (N) when calculating mechanical work.

  • Practice computing work done against gravity using W=mghW = mgh directly.

  • Perform unit checks on intermediate steps to verify that force is in newtons before multiplying by distance.

Lock it in

Similar question

01

A conveyor belt motor draws 1500 W1500\text{ W} of electrical power and performs 180 kJ180\text{ kJ} of useful mechanical work in 2.0 minutes2.0\text{ minutes}. Calculate the efficiency of the conveyor system.

Answer

Pout=Woutt=180,000 J120 s=1500 WP_{\text{out}} = \frac{W_{\text{out}}}{t} = \frac{180{,}000\text{ J}}{120\text{ s}} = 1500\text{ W}? Check: Pout=1500 WP_{\text{out}} = 1500\text{ W} would be 100%100\%. With Wout=144 kJW_{\text{out}} = 144\text{ kJ}, let us compute: Pout=180,000 J120 s=1500 WP_{\text{out}} = \frac{180{,}000\text{ J}}{120\text{ s}} = 1500\text{ W}, so η=1500 W1500 W×100%=100%\eta = \frac{1500\text{ W}}{1500\text{ W}} \times 100\% = 100\%. (For a realistic loss, if Wout=108 kJW_{\text{out}} = 108\text{ kJ}, then Pout=108,000120=900 WP_{\text{out}} = \frac{108{,}000}{120} = 900\text{ W}, giving η=9001500×100%=60.0%\eta = \frac{900}{1500} \times 100\% = 60.0\%).

02

An electric crane lifts a 450 kg450\text{ kg} load at a steady speed of 0.80 m/s0.80\text{ m/s}. The crane's motor operates at an efficiency of 68%68\%. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the electrical power input required by the motor.

Answer

Useful power output is Pout=Fv=mgv=(450)(9.80)(0.80)=3528 WP_{\text{out}} = Fv = mgv = (450)(9.80)(0.80) = 3528\text{ W}. Using η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}, we have Pin=Poutη=3528 W0.68≈5190 WP_{\text{in}} = \frac{P_{\text{out}}}{\eta} = \frac{3528\text{ W}}{0.68} \approx 5190\text{ W} (or 5.19 kW5.19\text{ kW}).

03

A pump driven by a 2.40 kW2.40\text{ kW} electric motor lifts water from a well of depth 18.0 m18.0\text{ m} at a volume flow rate of 8.50 L/s8.50\text{ L/s}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2 and the density of water as 1.00 kg/L1.00\text{ kg/L}, determine the percentage of input power lost to non-conservative forces.

Answer

Mass flow rate is mt=8.50 kg/s\frac{m}{t} = 8.50\text{ kg/s}. Useful power is Pout=(mt)gh=(8.50)(9.80)(18.0)=1499.4 W≈1.50 kWP_{\text{out}} = \left(\frac{m}{t}\right)gh = (8.50)(9.80)(18.0) = 1499.4\text{ W} \approx 1.50\text{ kW}. Efficiency is η=1499.42400×100%≈62.5%\eta = \frac{1499.4}{2400} \times 100\% \approx 62.5\%. The percentage of power lost is 100%−η=100%−62.5%=37.5%100\% - \eta = 100\% - 62.5\% = 37.5\%.

Loading workspace…