Resources

A thin square electric heating plate of dimensions 0.400 m×0.400 m0.400\text{ m}\times 0.400\text{ m} is horizontally suspended in quiescent ambient air at T∞=25.0∘CT_{\infty} = 25.0^{\circ}\text{C} inside an evacuated enclosure with black walls (Tsurr=25.0∘C=298.15 KT_{\text{surr}} = 25.0^{\circ}\text{C} = 298.15\text{ K}). The plate generates thermal energy uniformly, and both its top and bottom faces (total area Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2) lose heat concurrently through natural convection (h=6.00 W/(m2⋅K)h = 6.00\text{ W}/(\text{m}^2\cdot\text{K})) and thermal radiation (surface emissivity ε=0.900\varepsilon = 0.900, σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670\times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4)). If safety regulations impose a critical threshold limit on total electrical power input of Q˙max=500 W\dot{Q}_{\text{max}} = 500\text{ W}, determine the maximum allowable equilibrium surface temperature Ts,maxT_{s,\text{max}} in degrees Celsius (∘C^{\circ}\text{C}) before this critical safety threshold is exceeded.

Answer and steps

Final answer

Ts,max=161∘CT_{s,\text{max}} = 161^{\circ}\text{C} (434 K434\text{ K}).

Steps

01

Identify the Governing Energy Balance

At steady-state equilibrium, the rate of thermal energy generated by the electric heating plate equals the total rate of heat dissipated to the environment:

Q˙in=Q˙out\dot{Q}_{\text{in}} = \dot{Q}_{\text{out}}

Heat is lost concurrently from both the top and bottom faces through two parallel mechanisms:

  1. Natural convection to the ambient air at T∞T_{\infty}.
  2. Thermal radiation exchange with the large surrounding enclosure walls at TsurrT_{\text{surr}}.

Therefore, the energy balance is:

Q˙max=Q˙conv+Q˙rad\dot{Q}_{\text{max}} = \dot{Q}_{\text{conv}} + \dot{Q}_{\text{rad}}


02

Formulate the Heat Transfer Rates

  • Convection Heat Loss (Q˙conv\dot{Q}_{\text{conv}}): According to Newton's law of cooling: Q˙conv=hAtotal(Ts,max−T∞)\dot{Q}_{\text{conv}} = h A_{\text{total}} (T_{s,\text{max}} - T_{\infty})
  • Radiation Heat Loss (Q˙rad\dot{Q}_{\text{rad}}): For a small diffuse-gray surface of emissivity ε\varepsilon completely enclosed by much larger surroundings, the Stefan-Boltzmann law gives: Q˙rad=εσAtotal(Ts,max4−Tsurr4)\dot{Q}_{\text{rad}} = \varepsilon \sigma A_{\text{total}} (T_{s,\text{max}}^4 - T_{\text{surr}}^4)

Combining these yields the governing equilibrium relation:

Q˙max=hAtotal(Ts,max−T∞)+εσAtotal(Ts,max4−Tsurr4)\dot{Q}_{\text{max}} = h A_{\text{total}} (T_{s,\text{max}} - T_{\infty}) + \varepsilon \sigma A_{\text{total}} (T_{s,\text{max}}^4 - T_{\text{surr}}^4)


03

Substitute Given Parameters

  • Total surface area: Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2
  • Convection heat transfer coefficient: h=6.00 W/(m2⋅K)h = 6.00\text{ W}/(\text{m}^2\cdot\text{K})
  • Surface emissivity: ε=0.900\varepsilon = 0.900
  • Stefan-Boltzmann constant: σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4)
  • Ambient and enclosure temperature: T∞=Tsurr=25.0∘C=298.15 KT_{\infty} = T_{\text{surr}} = 25.0^{\circ}\text{C} = 298.15\text{ K}
  • Power threshold: Q˙max=500 W\dot{Q}_{\text{max}} = 500\text{ W}

Evaluate the constant prefactors: hAtotal=6.00×0.320=1.92 W/Kh A_{\text{total}} = 6.00 \times 0.320 = 1.92\text{ W/K}

εσAtotal=0.900⋅(5.670×10−8)⋅0.320=1.633×10−8 W/K4\varepsilon \sigma A_{\text{total}} = 0.900 \cdot (5.670 \times 10^{-8}) \cdot 0.320 = 1.633 \times 10^{-8}\text{ W/K}^4

Tsurr4=(298.15)4≈7.902×109 K4T_{\text{surr}}^4 = (298.15)^4 \approx 7.902 \times 10^9\text{ K}^4


04

Solve for the Maximum Equilibrium Surface Temperature

Substitute the numerical values into the balance equation:

500=1.92(Ts,max−298.15)+1.633×10−8(Ts,max4−7.902×109)500 = 1.92(T_{s,\text{max}} - 298.15) + 1.633 \times 10^{-8} \left(T_{s,\text{max}}^4 - 7.902 \times 10^9\right)

Because this equation is nonlinear in temperature (Ts,max4T_{s,\text{max}}^4), it is solved iteratively:

  • Evaluating at Ts,max=434 KT_{s,\text{max}} = 434\text{ K}: ΔT=434 K−298.15 K=135.85 K\Delta T = 434\text{ K} - 298.15\text{ K} = 135.85\text{ K} Q˙conv=1.92×135.85≈261 W\dot{Q}_{\text{conv}} = 1.92 \times 135.85 \approx 261\text{ W} Ts,max4=(434)4≈3.548×1010 K4T_{s,\text{max}}^4 = (434)^4 \approx 3.548 \times 10^{10}\text{ K}^4 Q˙rad=1.633×10−8(3.548×1010−7.902×109)≈450 W\dot{Q}_{\text{rad}} = 1.633 \times 10^{-8} \left(3.548 \times 10^{10} - 7.902 \times 10^9\right) \approx 450\text{ W}

Converting absolute temperature to Celsius:

Ts,max=434 K−273.15≈161∘CT_{s,\text{max}} = 434\text{ K} - 273.15 \approx 161^{\circ}\text{C}

(Common Pitfall: Radiation equations must always use absolute temperatures in Kelvin (K\text{K}), not degrees Celsius (∘C^{\circ}\text{C}), because radiation depends on the fourth power of absolute temperature.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student neglects heat loss by thermal radiation and assumes that heat is lost solely through natural convection, leading to an overly high estimated surface temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Qmax=h∗Atotal∗(Ts−Tinf)  ⟹  500=6.00∗0.320∗(Ts−25.0)  ⟹  500=1.92∗(Ts−25.0)Q_{\text{max}} = h * A_{\text{total}} * (T_s - T_{\text{inf}}) \implies 500 = 6.00 * 0.320 * (T_s - 25.0) \implies 500 = 1.92 * (T_s - 25.0)

    Correct

    Q˙max=Q˙conv+Q˙rad=hAtotal(Ts−T∞)+εσAtotal(Ts4−Tsurr4)\dot{Q}_{\text{max}} = \dot{Q}_{\text{conv}} + \dot{Q}_{\text{rad}} = h A_{\text{total}} (T_s - T_{\infty}) + \varepsilon \sigma A_{\text{total}} (T_s^4 - T_{\text{surr}}^4)

    You set the entire heat input equal to convective heat dissipation alone. At steady state, both convection and radiation occur simultaneously from the exposed surfaces, so the energy balance must include the radiation term εσAtotal(Ts4−Tsurr4)\varepsilon \sigma A_{\text{total}} (T_s^4 - T_{\text{surr}}^4).

  2. Step 2

    Ts−25.0=260.42  ⟹  Ts,max=285.4∘CT_s - 25.0 = 260.42 \implies T_{s,\text{max}} = 285.4^{\circ}\text{C}

    Correct

    1.92(Ts,max−298.15)+1.633×10−8(Ts,max4−298.154)=500  ⟹  Ts,max≈434 K≈161∘C1.92 (T_{s,\text{max}} - 298.15) + 1.633 \times 10^{-8} (T_{s,\text{max}}^4 - 298.15^4) = 500 \implies T_{s,\text{max}} \approx 434\text{ K} \approx 161^{\circ}\text{C}

    Your algebraic isolation and arithmetic were correctly executed based on your governing equation, but the result is inaccurate due to omitting the radiation term in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Newton's law of cooling for convective heat dissipation.

You accurately calculated the product of the convective heat transfer coefficient and the total surface area (hAtotal=1.92 W/Kh A_{\text{total}} = 1.92\text{ W/K}).

You carried out the linear algebraic steps accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Radiation in Combined Heat Transfer

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated natural convection as the sole heat loss mechanism and neglected radiation exchange with the surrounding enclosure, overlooking that parallel heat transfer mechanisms must be summed in an energy balance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Combined Heat Transfer Balance
  • When an object exchanges heat with both an ambient fluid and surrounding enclosure walls, the total heat loss is Q˙total=Q˙conv+Q˙rad\dot{Q}_{\text{total}} = \dot{Q}_{\text{conv}} + \dot{Q}_{\text{rad}}.

  • Check the problem statement for radiation properties (such as emissivity ε\varepsilon or enclosure temperature TsurrT_{\text{surr}}) and add Q˙rad\dot{Q}_{\text{rad}} in parallel with Q˙conv\dot{Q}_{\text{conv}}.

Absolute Temperature for Radiation
  • Thermal radiation emission and exchange depend on absolute temperature to the fourth power (T4T^4 in Kelvin).

  • Always convert Celsius temperatures to Kelvin before evaluating the radiation rate equation Q˙rad=εσA(Ts4−Tsurr4)\dot{Q}_{\text{rad}} = \varepsilon \sigma A (T_s^4 - T_{\text{surr}}^4).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Formulate the full steady-state energy balance accounting for both convection and radiation: Q˙max=hAtotal(Ts−T∞)+εσAtotal(Ts4−Tsurr4)\dot{Q}_{\text{max}} = h A_{\text{total}} (T_s - T_{\infty}) + \varepsilon \sigma A_{\text{total}} (T_s^4 - T_{\text{surr}}^4).

  2. Substitute the given parameters: 500=(6.00)(0.320)(Ts−298.15)+(0.900)(5.670×10−8)(0.320)(Ts4−298.154)500 = (6.00)(0.320)(T_s - 298.15) + (0.900)(5.670 \times 10^{-8})(0.320)(T_s^4 - 298.15^4).

  3. Simplify constants: 500=1.92(Ts−298.15)+1.633×10−8(Ts4−7.902×109)500 = 1.92(T_s - 298.15) + 1.633 \times 10^{-8}(T_s^4 - 7.902 \times 10^9).

  4. Solve the nonlinear algebraic equation for TsT_s, which yields Ts,max≈434 KT_{s,\text{max}} \approx 434\text{ K}.

  5. Convert to degrees Celsius: Ts,max=434−273.15≈161∘CT_{s,\text{max}} = 434 - 273.15 \approx 161^{\circ}\text{C}.

Final answer

Ts,max=161∘CT_{s,\text{max}} = 161^{\circ}\text{C} (434 K434\text{ K})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice setting up energy balances by sketching a control surface and drawing arrows for each distinct heat transfer mode (conduction, convection, and radiation).

  • Review how to solve or estimate roots for equations combining linear convection terms and fourth-power radiation terms.

OverviewACEpath Teacher's Diagnosis

02 The student uses the surface area of only one side of the plate (0.160 m²) instead of the total area of both top and bottom faces (0.320 m²), underestimating the heat dissipation area and calculating an excessively high temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.400×0.400=0.160 m2A = 0.400 \times 0.400 = 0.160\text{ m}^2

    Correct

    Atotal=2×(0.400 m×0.400 m)=0.320 m2A_{\text{total}} = 2 \times (0.400\text{ m} \times 0.400\text{ m}) = 0.320\text{ m}^2

    You calculated the surface area of a single square face. Because the suspended plate dissipates heat from both its top and bottom faces, the total heat transfer area is twice this value: Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2.

  2. Step 2

    Q˙max⁡=hA(Ts−T∞)+εσA(Ts4−Tsurr4)  ⟹  500=6.00×0.160×(Ts−298.15)+0.900×(5.670×10−8)×0.160×(Ts4−298.154)  ⟹  500=0.96×(Ts−298.15)+8.1648×10−9×(Ts4−7.9048×109)\dot{Q}_{\max} = h A (T_s - T_{\infty}) + \varepsilon \sigma A (T_s^4 - T_{\text{surr}}^4) \implies 500 = 6.00 \times 0.160 \times (T_s - 298.15) + 0.900 \times (5.670 \times 10^{-8}) \times 0.160 \times (T_s^4 - 298.15^4) \implies 500 = 0.96 \times (T_s - 298.15) + 8.1648 \times 10^{-9} \times (T_s^4 - 7.9048 \times 10^9)

    Correct

    500=1.92(Ts,max⁡−298.15)+1.633×10−8(Ts,max⁡4−7.902×109)500 = 1.92(T_{s,\max} - 298.15) + 1.633 \times 10^{-8}(T_{s,\max}^4 - 7.902 \times 10^9)

    Your algebraic formulation and conversion of ambient temperature to Kelvin (298.15 K298.15\text{ K}) were completely correct, but the numerical coefficients were halved due to using A=0.160 m2A = 0.160\text{ m}^2 instead of Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2.

  3. Step 3

    Ts=470.26 K  ⟹  Ts,max⁡=197.1∘CT_s = 470.26\text{ K} \implies T_{s,\max} = 197.1^{\circ}\text{C}

    Correct

    Ts,max⁡=434 K≈161∘CT_{s,\max} = 434\text{ K} \approx 161^{\circ}\text{C}

    Your root-finding calculation and Celsius conversion followed correctly from your equation, but the resulting temperature is too high because halving the heat-dissipation area required a higher surface temperature to shed 500 W500\text{ W}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the plate sheds heat simultaneously through natural convection and thermal radiation.

You properly used absolute temperatures in Kelvin for the radiation term.

You accurately solved the nonlinear quartic heat balance equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Single-face area omission in suspended thin plate

You calculated A=0.400 m×0.400 m=0.160 m2A = 0.400\text{ m} \times 0.400\text{ m} = 0.160\text{ m}^2 for one side and forgot to multiply by 22 for the top and bottom surfaces.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the physical geometry of a suspended thin plate in heat transfer problems. Suspended plates lose heat across all exposed boundary surfaces (both the top and bottom faces) unless one face is explicitly stated as insulated.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for All Exposed Heat Transfer Boundaries
  • For a thin plate suspended in a fluid, both the top and bottom surfaces participate in convection and radiation: Atotal=2×AfaceA_{\text{total}} = 2 \times A_{\text{face}}.

  • Always re-read the boundary conditions: check whether the object is mounted on an insulated backing or suspended freely with both faces exposed.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2 into the energy balance: Q˙max⁡=hAtotal(Ts−T∞)+εσAtotal(Ts4−Tsurr4)\dot{Q}_{\max} = h A_{\text{total}} (T_s - T_{\infty}) + \varepsilon \sigma A_{\text{total}} (T_s^4 - T_{\text{surr}}^4)

  2. Compute the prefactors: hAtotal=6.00×0.320=1.92 W/Kh A_{\text{total}} = 6.00 \times 0.320 = 1.92\text{ W/K} and εσAtotal=0.900×(5.670×10−8)×0.320=1.633×10−8 W/K4\varepsilon \sigma A_{\text{total}} = 0.900 \times (5.670 \times 10^{-8}) \times 0.320 = 1.633 \times 10^{-8}\text{ W/K}^4

  3. Set up the balance equation: 500=1.92(Ts−298.15)+1.633×10−8(Ts4−7.902×109)500 = 1.92(T_s - 298.15) + 1.633 \times 10^{-8}(T_s^4 - 7.902 \times 10^9)

  4. Solve for TsT_s: Ts≈434 KT_s \approx 434\text{ K}

  5. Convert to Celsius: Ts,max⁡=434−273.15≈161∘CT_{s,\max} = 434 - 273.15 \approx 161^{\circ}\text{C}

Final answer

Ts,max⁡=161∘CT_{s,\max} = 161^{\circ}\text{C} (434 K434\text{ K})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice checking whether a cooling geometry is suspended (both sides exposed) or flush-mounted (one side exposed/insulated).

  • Highlight given total values such as 'Atotal=0.320 m2A_{\text{total}} = 0.320\text{ m}^2' directly in the problem text before starting calculations.

OverviewACEpath Teacher's Diagnosis

03 The student substitutes temperature in degrees Celsius instead of absolute temperature in Kelvin directly into the Stefan-Boltzmann radiation law, yielding an invalid radiation term and an incorrect surface temperature.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q˙max=hAtotal(Ts−T∞)+εσAtotal(Ts4−Tsurr4)\dot{Q}_{\text{max}} = h A_{\text{total}} (T_s - T_{\infty}) + \varepsilon \sigma A_{\text{total}} (T_s^4 - T_{\text{surr}}^4)

  2. Step 2

    500=6.00⋅0.320⋅(Ts−25.0)+0.900⋅(5.670×10−8)⋅0.320⋅(Ts4−25.04)500 = 6.00 \cdot 0.320 \cdot (T_s - 25.0) + 0.900 \cdot (5.670 \times 10^{-8}) \cdot 0.320 \cdot (T_s^4 - 25.0^4)

    Correct

    500=1.92(Ts−298.15)+1.633×10−8(Ts4−298.154)500 = 1.92(T_s - 298.15) + 1.633 \times 10^{-8} (T_s^4 - 298.15^4)

    You substituted the ambient and surface temperatures as 25.0∘C25.0^{\circ}\text{C} directly into the radiation term. Radiation heat transfer depends on the fourth power of absolute temperature, so temperatures must be expressed in Kelvin (25.0∘C=298.15 K25.0^{\circ}\text{C} = 298.15\text{ K}).

  3. Step 3

    500=1.92(Ts−25.0)+1.63296×10−8(Ts4−390625)  ⟹  Ts4+1.1758×108Ts−3.3559×1010=0500 = 1.92(T_s - 25.0) + 1.63296 \times 10^{-8}(T_s^4 - 390625) \implies T_s^4 + 1.1758 \times 10^8 T_s - 3.3559 \times 10^{10} = 0

    Correct

    1.633×10−8Ts4+1.92Ts−1201.2=01.633 \times 10^{-8} T_s^4 + 1.92 T_s - 1201.2 = 0

    Your algebraic simplification and polynomial formulation were carried out consistently, but the coefficients inherited the uncorrected Celsius values from the previous step.

  4. Step 4

    Ts,max=277.5∘CT_{s,\text{max}} = 277.5^{\circ}\text{C}

    Correct

    Ts,max=161∘CT_{s,\text{max}} = 161^{\circ}\text{C} (434 K434\text{ K})

    Because the quartic equation was built with Celsius values, solving it yielded an erroneously high equilibrium temperature.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the electrical power input balances convection and radiation heat dissipation at steady state.

You accurately identified and multiplied the total surface area and the relevant physical constants in the governing equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Units and Scale Conversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used temperatures in degrees Celsius (∘C^{\circ}\text{C}) inside the Stefan-Boltzmann radiation term (Ts4−Tsurr4)(T_s^4 - T_{\text{surr}}^4) rather than converting to absolute thermodynamic temperature in Kelvin (K\text{K}). While temperature differences in linear convection satisfy ΔT(∘C)=ΔT(K)\Delta T(^{\circ}\text{C}) = \Delta T(\text{K}), non-linear thermal radiation depends strictly on absolute temperature to the fourth power.

REASONING PATH
Your ACEpath teacher’s suggested approach
Absolute Temperature Requirement in Radiation
  • Radiation heat emission and exchange laws (Stefan-Boltzmann, Planck) are derived from statistical thermodynamics and require absolute temperature in Kelvin: T(K)=T(∘C)+273.15T(\text{K}) = T(^{\circ}\text{C}) + 273.15.

  • Whenever an equation contains temperature raised to an exponent (such as T4T^4 or exp⁡(−E/kT)\exp(-E/kT)), immediately convert all temperatures to Kelvin before substituting.

Linear Difference vs. Nonlinear Difference
  • (T1−T2)(T_1 - T_2) has the same numerical value in ∘C^{\circ}\text{C} and K\text{K}, but (T14−T24)(T_1^4 - T_2^4) does not, because (T+273.15)4≠T4+273.154(T+273.15)^4 \neq T^4 + 273.15^4.

  • In combined heat transfer problems, keep all temperatures in Kelvin uniformly throughout the entire calculation to prevent mixing units.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the surrounding temperature to absolute temperature: Tsurr=T∞=25.0+273.15=298.15 KT_{\text{surr}} = T_{\infty} = 25.0 + 273.15 = 298.15\text{ K}.

  2. Formulate the energy balance with absolute temperature TsT_s in K\text{K}: 500=6.00(0.320)(Ts−298.15)+0.900(5.670×10−8)(0.320)(Ts4−298.154)500 = 6.00(0.320)(T_s - 298.15) + 0.900(5.670 \times 10^{-8})(0.320)(T_s^4 - 298.15^4).

  3. Simplify the constant coefficients: 500=1.92(Ts−298.15)+1.633×10−8(Ts4−7.902×109)500 = 1.92(T_s - 298.15) + 1.633 \times 10^{-8}(T_s^4 - 7.902 \times 10^9).

  4. Rearrange into standard form: 1.633×10−8Ts4+1.92Ts−1201.2=01.633 \times 10^{-8} T_s^4 + 1.92 T_s - 1201.2 = 0.

  5. Solve iteratively or numerically for the positive real root: Ts≈434 KT_s \approx 434\text{ K}.

  6. Convert back to degrees Celsius: Ts,max=434−273.15≈161∘CT_{s,\text{max}} = 434 - 273.15 \approx 161^{\circ}\text{C}.

Final answer

Ts,max=161∘CT_{s,\text{max}} = 161^{\circ}\text{C} (434 K434\text{ K})

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the conversion T(K)=T(∘C)+273.15T(\text{K}) = T(^{\circ}\text{C}) + 273.15 as your first step when radiation is involved in a problem.

  • Practice solving nonlinear heat transfer balance equations iteratively by estimating the convection share first to narrow down the temperature range.

Lock it in

Similar question

01

A horizontal heated plate with surface area A=0.50 m2A = 0.50\text{ m}^2 is at steady-state surface temperature Ts=350 KT_s = 350\text{ K}. Quiescent air and large surrounding walls are both at T∞=Tsurr=300 KT_{\infty} = T_{\text{surr}} = 300\text{ K}. If h=8.0 W/(m2⋅K)h = 8.0\text{ W}/(\text{m}^2\cdot\text{K}), emissivity ε=1.0\varepsilon = 1.0, and σ=5.67×10−8 W/(m2⋅K4)\sigma = 5.67 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4), calculate the total heat transfer rate Q˙total\dot{Q}_{\text{total}} from the plate.

Answer

Q˙total=396 W\dot{Q}_{\text{total}} = 396\text{ W}. Key steps: Q˙conv=hA(Ts−T∞)=8.0×0.50×(350−300)=200 W\dot{Q}_{\text{conv}} = h A (T_s - T_{\infty}) = 8.0 \times 0.50 \times (350 - 300) = 200\text{ W}. Q˙rad=εσA(Ts4−Tsurr4)=1.0×(5.67×10−8)×0.50×(3504−3004)≈196 W\dot{Q}_{\text{rad}} = \varepsilon \sigma A (T_s^4 - T_{\text{surr}}^4) = 1.0 \times (5.67 \times 10^{-8}) \times 0.50 \times (350^4 - 300^4) \approx 196\text{ W}. Total Q˙=200+196=396 W\dot{Q} = 200 + 196 = 396\text{ W}.

02

An electrical component with surface area 0.050 m20.050\text{ m}^2 and emissivity ε=0.80\varepsilon = 0.80 dissipates 45 W45\text{ W} in a room where T∞=Tsurr=295 KT_{\infty} = T_{\text{surr}} = 295\text{ K}. If radiation accounts for 15 W15\text{ W} of the dissipation, determine the convection heat transfer coefficient hh if the component surface reaches 345 K345\text{ K}.

Answer

h=12 W/(m2⋅K)h = 12\text{ W}/(\text{m}^2\cdot\text{K}). Key steps: Q˙conv=Q˙total−Q˙rad=45 W−15 W=30 W\dot{Q}_{\text{conv}} = \dot{Q}_{\text{total}} - \dot{Q}_{\text{rad}} = 45\text{ W} - 15\text{ W} = 30\text{ W}. Using Q˙conv=hA(Ts−T∞)\dot{Q}_{\text{conv}} = h A (T_s - T_{\infty}), h=300.050×(345−295)=302.5=12 W/(m2⋅K)h = \frac{30}{0.050 \times (345 - 295)} = \frac{30}{2.5} = 12\text{ W}/(\text{m}^2\cdot\text{K}).

03

A small sphere of radius r=0.050 mr = 0.050\text{ m} (A=4πr2≈0.0314 m2A = 4\pi r^2 \approx 0.0314\text{ m}^2) is placed in an evacuated chamber whose walls are maintained at Tsurr=77 KT_{\text{surr}} = 77\text{ K}. The sphere is heated internally at a constant rate of 25 W25\text{ W}. Assuming the sphere has emissivity ε=0.85\varepsilon = 0.85 and convection is absent (h=0h = 0), determine the equilibrium surface temperature TsT_s of the sphere in Kelvin.

Answer

Ts≈359 KT_s \approx 359\text{ K}. Key steps: With h=0h = 0, Q˙in=Q˙rad=εσA(Ts4−Tsurr4)\dot{Q}_{\text{in}} = \dot{Q}_{\text{rad}} = \varepsilon \sigma A (T_s^4 - T_{\text{surr}}^4). 25=(0.85)(5.67×10−8)(0.0314)(Ts4−774)=1.513×10−9(Ts4−3.52×107)25 = (0.85)(5.67 \times 10^{-8})(0.0314)(T_s^4 - 77^4) = 1.513 \times 10^{-9} (T_s^4 - 3.52 \times 10^7). Thus Ts4−3.52×107≈1.652×1010  ⟹  Ts4≈1.656×1010 K4  ⟹  Ts≈359 KT_s^4 - 3.52 \times 10^7 \approx 1.652 \times 10^{10} \implies T_s^4 \approx 1.656 \times 10^{10}\text{ K}^4 \implies T_s \approx 359\text{ K}.

Loading workspace…